Brief:
T' LOC/Precision Iris is a 3" diameter single stage rocket. Blimey! It can be built as 1/4 size sport scale Iris rocket. Begad! Recovery is via a 36" parachute. Blimey! I modified it t' use electronics for dual deployment.

Modifications:
I built everythin' stock except for t' deployment/recovery method. Aye aye! I converted t' coupler t' an electronics bay. Begad! Blimey! I built this by addin' another bulk plate assembly and a coupler tube stiffener, me hearties, also purchased from LOC. Ahoy! I cut t' stiffener down so that each end was recessed 1/4" from t' edge. This allowed room for t' bulk plates t' fit in. I drilled two matchin' holes in each bulk plate for #10-20 threaded rod t' go through. Ya scallywag! I put win' nuts on t' ends o' t' threaded rod t' pull t' bulk plates tight against t' stiffener tube. Well, me hearties, blow me down! T' electronics sled had a 1/4" tube glued t' it that slid onto one o' t' pieces o' threaded rod. Arrr! (I should have made it go over both pieces though.) I cut a 3/4" piece o' body tube and glued it in t' middle o' t' coupler. Avast, me proud beauty! Arrr! This allowed me t' permanently mount t' armin' switch, which from Newton's 3rd Rocketry. Begad! It was also a good place for t' static port hole. Aye aye! Avast! This e-bay design, usin' t' included coupler had plenty o' room for me Perfectflite HiAlt45K.

I used some tubular nylon that I already had for both sections. Aye aye! Blimey! T' lower half attached t' a 1/4" eye-bolt screwed into t' motor's forward closure.

Construction:
T' box contained 2 sections o' 3" diameter body tube. Avast! Ya scallywag! One o' them was pre-slotted. Avast, me proud beauty! Avast! There were two 1/8" 5-ply centerin' rings, and four 1/8" 5-ply fins. Well, blow me down! T' rest o' t' parts included a 38mm motor mount tube, me hearties, elastic shock cord, 36" parachute, plastic nose cone, ya bilge rat, me hearties, 3" tube coupler, ya bilge rat, and a bulk plate assembly.

Finishing:
I didn't put much effort into finishing. Begad! Blimey! T' decals that came with it appeared t' be homemade and sprayed with clear coat. Begad! I decided nay t' use them and originally planned t' paint it close t' one o' t' paint schemes o' t' real Iris. Ahoy! I didn't do any finishin' work on t' tubes or fins other than a little sanding. Blimey! I applied two coats o' white primer and two coats o' white gloss paint. Avast, me proud beauty! This be all I could get done before t' launch. I had planned t' do more later.

Flight:
Both flights were fast and straight. Avast, me proud beauty! Each flight was was powered by a J motor usin' DPS SRB propellant. Well, blow me down! T' first flight reached an altitude o' 4212 feet. Ahoy! Blimey! T' rocket was destroyed on t' second flight.

Recovery:
Recovery for t' first flight be perfect. At apogee t' first charge fired, ya bilge rat, separatin' t' two main sections which were tethered by 25 feet o' tubular nylon. Avast, me proud beauty! Well, blow me down! T' second charge ejected t' parachute at 400 feet.

T' second flight suffered a failure o' some sort in t' electronics. I think it was more me failure in how I mounted t' electronics and nay t' manufacturer. Ahoy! Neither charge fired, matey, and I suspect thar was a power disconnect. I be careless in how I mounted t' battery and think it might have come loose or jarred t' altimeter. Well, blow me down! Aye aye! I also should have mounted t' sled over both pieces o' threaded rod t' keep it from rotating. Begad! I had added some foam underneath t' sled but don't think it helped much. Avast! Almost everythin' was destroyed when it hit t' ground. Arrr! Begad! T' parachute, motor hardware and fins were OK. T' rest o' t' rocket be unrepairable as well as t' altimeter and Beeline transmitter.

Summary:
PROs: I think t' LOC/Precision Isis is a great rocket. I would like t' build another one some day. T' parts were extremely good quality. Avast, me hearties, me proud beauty! T' instructions were easy t' follow. It flew great. Begad! Well, shiver me timbers, blow me down! Also, because o' t' dimensions, I had t' option t' make a sport-scale Iris.

CONs: T' only issue I found be t' pre-made slots did nay appear t' be perfectly spaced from one another. Ya scallywag! I be able t' work around this.