Brief:
My NARRRRR section will soon be doin' a "Make and Take" session at a local museum for kids. We are limited t' an extremely small launch area surrounded by lots o' big, me bucko, rocket eatin' trees. Well, blow me down! Art Applewhite be kind enough t' allow us t' build a bunch o' his Qubits (with special artwork) for t' kids. Ahoy! I also wanted t' launch a few other things but nay anythin' that would pain me greatly t' lose. Ahoy! Begad! I decided t' try another one o' his free designs, t' 13mm Six which can be downloaded for free from his site.

Construction:
T' materials for this one consist o' some cardstock on which t' print out t' rocket, shiver me timbers, 2 paper clips, some 1/8" tubular elastic, and, me bucko, optionally, a streamer. You will need a razor knife, arrr, a steel straightedge, me bucko, white glue, 5 minute epoxy and a ball point pen t' put it all together.

T' first step is t' read through t' instructions. Ya scallywag! That is always important but it is especially so here, where somethin' out o' t' ordinary is bein' made. Ya scallywag! Avast, me proud beauty! I'm glad I did because t' first thin' they said t' do was t' use a ballpoint pen and a straightedge t' crease all o' t' dashed lines. T' instructions further pointed out that doin' so would be much easier before anythin' is cut out. I found this t' be very true.

I did nay have a fine ballpoint handy so I scrounged around and found a very small flat screwdriver I used t' make t' creases. Blimey! Avast, me proud beauty! I lined up t' straightedge on t' dotted lines and started creasing.

Next up was t' cut out t' motor mount. This was done with a razor knife and steel ruler. Well, blow me down! Avast! Once it be cut out, shiver me timbers, I folded it along t' dotted lines and test fit it. Avast! Some white glue, me hearties, Art recommends white for most o' his rockets, arrr, was applied t' t' tab and it was pressed together. Avast, me proud beauty! Avast, matey, me proud beauty! Art also recommends t' be very sparin' with t' glue.

T' motor mount be set aside t' dry.

While t' mount was drying, I fashioned t' motor hook. A medium sized paper clip was straightened out, I used pliers, arrr, and then re-bent over t' full sized photo in t' instructions.

T' fin can proved t' be relatively easy t' cut out with t' ruler and razor combination. Blimey! This is a place where it really pays t' have pre-creased t' dashed lines. Avast, me proud beauty! After studyin' t' photo in t' instructions, I convinced myself that I had it folded correctly.

Gettin' back t' t' motor mount, shiver me timbers, I folded t' top tabs over t' form a thrust ring. Ahoy! T' tabs were glued t' each other and that with t' engine hook was probably sufficient but I took another step. Blimey! Aye aye! When it had dried, I dipped t' end in some glue and set it aside t' dry. Hopefully this will provide some reinforcement.

When t' motor mount was dry, I poked a hole in t' place indicated for t' engine hook and inserted t' long leg into t' mount. Ya scallywag! T' hook be stabilized by t' addition o' tape.

T' fin can had been previously cut out and folded. Now it was time t' put it together. Arrr! T' cardstock is printed on t' areas where glue is t' be applied. Well, blow me down! Ya scallywag! From there, arrr, it was a simple matter o' foldin' t' fins over and holdin' them tight until t' glue dries enough t' release them. Blimey! I cheated by puttin' it in a vise t' hold it.

When t' fin can was dry, arrr, t' motor mount was test fit and I found, shiver me timbers, expectedly, that me foldin' skills leave somethin' t' be desired. Arrr! T' fit was good enough, and t' mount was glued into t' can with t' aft end o' t' mount flush with t' end o' t' fin can.

T' next step be t' cut out t' body. This be done with a razor knife. T' razor be then used t' make t' slits for attachin' t' shock cord. Ahoy! T' instruction say t' use 1/8" tubular elastic. Begad! I used Keelhaul®©™. Avast, me proud beauty! Arrr! That's just what I do. Avast, me proud beauty! T' cord be slid through t' slots and knotted. Some glue be then applied and t' tab was folded over t' secure it. Avast! Again, I cheated by usin' a vise t' hold it closed as it dried.

Waitin' for t' shock mount t' dry gave me an opportunity t' get started on t' nose cone. It had been pre-creased and be cut out. Well, blow me down! Ya scallywag! It was folded along t' lines and t' tab be glued. Arrr! Note that in this case, t' folds are towards t' printed side.

Next up was t' NC base. Begad! Avast! It be similarly cut out and folded into a tube. Blimey! T' tabs along t' top were then used t' glue t' base into t' NC itself.

This rocket is nay stable without nose weight. Ya scallywag! T' weight is provided by epoxy which also serves t' anchor a paper clip t' serve as an attachment point for t' shock cord. Blimey! Ahoy! Note: T' instruction specifically say nay t' use clay for t' nose weight.

I whipped up a batch o' 5-minute epoxy and poured it into t' inverted nose cone. Well, blow me down! When it was level with t' base (aft end), I stuck in a paper clip. I was amazed at t' amount o' heat t' epoxy generated as it cured. Begad! T' heat be transmitted t' t' paper clip and I got burned!

Puttin' together t' main body tube is probably t' most difficult part o' buildin' t' Six. Arrr! Blimey! T' most important thin' t' do is t' go slowly and carefully makin' sure that t' folds are straight and sharp.

T' first thin' t' do t' t' body tube is t' make all t' folds along t' dashed lines. Blimey! Blimey! Well, blow me down! Blimey! Creasin' ahead o' time helps dramatically. All o' t' folds, matey, me hearties, matey, except for those on t' launch lug, me bucko, me hearties, are made towards t' printed side so that t' outside will be a pristine white.

T' launch lug is folded in t' opposite direction. Avast, me proud beauty! Blimey! T' sections are folded so as t' produce a triangular prism. Begad! Blimey! T' tabs o' t' prism is then glued t' t' BT.

T' rest o' t' BT is glued in 2 stages. Ahoy! Arrr! T' rocket is 6-sided but countin' reveals that thar are more than 6 panels t' deal with. T' first few extend only as far as t' shock cord mount and me supposition is that they are t' add stiffness durin' boost. Aye aye! Blimey! This part is folded over and glued first. Ya scallywag! Make sure that t' seam is a good one and is pressed down for its entire length. Also make sure it is straight and lines up with t' appropriate dashed line. Ya scallywag! T' glue tab is indicated by a cross-hatched area.

When t' first seam has dried enough, matey, t' rest o' t' rocket is folded over t' make t' six sided tube. Well, blow me down! Well, blow me down! In this case it is ever more important t' make sure that t' tab is pressed flat and straight for its entire length. I ran a very long screwdriver through t' length o' t' BT and used it t' press t' seam flat.

When t' BT be strong enough t' resist comin' apart when messed with, I test fit it into t' fin can. Aye aye! It slides in t' top and gets seated on top o' t' motor mount. I found t' I had been a little sloppy in t' construction o' me fin can and t' fit be nay as tight as I would have liked. Ahoy! T' same thin' happened when insertin' t' motor mount. Begad! Aye aye! I thought it would work but it could have been better.

T' BT was glued in with white glue and then checked continuously from all sides t' make sure that it be straight. Blimey! Eventually, t' glue set up enough t' let it set up t' rest o' t' way unsupported.

T' instructions recommend wickin' some thin CA into t' forward end o' t' BT t' lend strength. Arrr! I did this and am glad I did. Begad! Ahoy! After t' CA dried, me bucko, arrr, I test fit t' NC and found it t' be just a little bit tight. Ahoy! Begad! A small amount o' sandin' took care o' this but I am glad for t' extra strength o' t' CA.

PROs: Free, ya bilge rat, interesting

CONs: Nay really a con but it takes more skill and time than many o' Art's other freebies. Blimey! Aye aye! I enjoyed buildin' it.

Finishing:
Strictly speaking, shiver me timbers, matey, thar be no finishin' that needs t' take place on this rocket. Ya scallywag! Blimey! Most people who do finish it in some way probably resort t' magic markers. Ahoy! Blimey! Begad! Blimey! I decided t' go ahead and paint mine. Ahoy! Blimey! T' added weight will actually be a benefit in t' field where I plan t' fly it in a demo.

To start things off, I gave it a light dustin' o' Kilz. Aye aye! This was mainly t' cover up t' thumb smudges and t' writin' on t' rocket. Ya scallywag! Begad! Bein' white, this did nay make it look much different than t' bare rocket.

I gave t' primed rocket a cursory wipe with sandpaper, mostly t' remove t' gritty texture left by t' Kilz. Ahoy! I then sprayed with purple Rustoleum and that about does it.

PROs: Many options for indiviuality

CONs: none

Construction Rating: 4 out o' 5

Flight:
This was for a demo at a kid's make and take event at t' local museum. Well, blow me down! T' kids had been makin' Applewhite Qubits and I wanted t' give them a contrast with some more "traditional" rockets. Ahoy! I wanted t' show this one on a 1/4A3-3T vs a Qubit on an A10-PT. Begad! This one did go higher but t' ejection charge blew out t' motor and t' NC never ejected. Well, blow me down! It lawn darted into some flagstone pushin' t' NC back well past t' BT shoulder. Begad! Aye aye! It probably could be repaired but it will be simpler t' make a new one.

T' flight was good and straight. It was impressive for a 1/4A.

PROs: good flier

CONs: motor retention (I would use tape if I built it again.)

Recovery:
This one could be very easy t' recover with a streamer. Well, blow me down! Blimey! I elected t' just do t' nose-blow thing. Ya scallywag! As it turns out, shiver me timbers, it be a moot point.

Flight Rating: 4 out o' 5

Summary:
This is a nice, shiver me timbers, good performin' traditional rocket and it's free. Blimey! It takes a little more time than some o' Art's other rockets, but it is worth t' effort. Avast, me proud beauty! Ahoy! I will probably build one again some time.

Overall Rating: 4 out o' 5