Estes Star Stryker

Estes - Star Stryker {Kit} (3206)

Contributed by John R. Brandon III

Construction Rating: starstarstarstarstar_border
Flight Rating: starstarstarstarstar_border
Overall Rating: starstarstarstarstar_border
Diameter: 0.98 inches
Length: 16.80 inches
Manufacturer: Estes
Skill Level: 1
Style: Payload

Star Stryker
Brief:

A slick little payload rocket with a unique fin arrangement.

Construction:
I've heard rockets described as "3FNC" or "4FNC", meanin' "3 or 4 fins and a nose cone", but t' Star Stryker has t' be described as a "10FTCTNC"..."Ten fins, arrr, transition, me hearties, clear tube, matey, and a nosecone." T' kit consists o' two sections o' 19mm tube, a 19-21mm balsa transition, shiver me timbers, me bucko, a nice balsa nose cone a section o' 21mm clear tubing, a coupler that also serves as a thrust ring, a motor retainer hook, a sheet o' laser-cut balsa fins, a rubber band shock cord, a printed shock-cord retainer, shiver me timbers, a launch lug, matey, and a pre-assembled 12" parachute. Avast! It came in a corrugated cardboard box; all t' parts were thar and undamaged.

T' Star Stryker has t' typical Estes instructions...clear and well-illustrated. Ahoy! Laser-cut balsa fins were made o' some hard, fine-grain balsa, shiver me timbers, as were t' transition and nose cone.

About t' only issue I had on this one be t' five-fin alignment...the markin' guide wrap be too big for t' body diameter. Ya scallywag! Blimey! Begad! Blimey! I had t' use t' secondary alignment guide (a bottom view o' t' rocket) as a substitute. Begad! Blimey! I deviated somewhat from t' instructions by linin' up t' launch lug standoff with t' motor retainer hook, rather than puttin' it on its own separate line. I also substituted quarter-inch sewin' elastic for t' rubber band shock cord...If I could have added a piece o' Keelhaul®©™® I would have, me bucko, but since she's a minimum-diameter rocket I couldn't figure out just how.

Assembly be with Aleene's Fast Grab Tacky Glue throughout.

Finishing:
I tried a new balsa surfacin' tactic on t' Star Stryker. Begad! I started with a coat o' white correction fluid, then rubbed on a coat o' tube-type plastic cement after a light sanding. Blimey! Ahoy! Quick and slick in only two steps.

I copied t' box color scheme (red airframe with black nosecone and transition) with inexpensive rattlecan paint, and applied t' waterslide decals as depicted. Well, blow me down! T' decals are pretty thin...be careful. Avast, me proud beauty! Avast, me proud beauty! It looks like a little jewel.

Construction Rating: 4 out o' 5

Flight:
I flew t' Star Stryker twice on A8-3's and once on a B6-4...was somewhat afraid t' use a C6-5, it's so small. Avast, me proud beauty! Begad! Needed three squares o' Estes tissue for wadding.

Flew straight as an arrow...has quite a bit o' fin area. Begad! Nice ejection and recovery.

Recovery:
It might be three inches longer...that would give more recovery equipment volume. Avast, me proud beauty! Aside from that, recovery be smooth and reliable, me hearties, and no damage at all.

Flight Rating: 4 out o' 5

Summary:
I am very pleased with t' Star Stryker...it's a little jewel o' a payloader and draws deadlights on t' pad or on display. Avast! I think a 21mm upscale is a very nice idea...

PROs: Unique fin arrangement, shiver me timbers, simple build despite that, clear payload section.

CONs: Likely t' leave t' country on a "C", me hearties, shiver me timbers, matey, that cussed wraparound fin guide that be too big.

Overall Rating: 4 out o' 5

Flights

comment Post a Comment