Brief:
This is a single stage, 4 finned payload rocket by Vaughn Brothers Rocketry. This rocket can achieve some pretty extreme altitude on a G42 or G55 motor. Arrr! Fin attachment is through t' wall.

Construction:
This kit contains:

• 2 body tubes, shiver me timbers, one for t' payload section and one for t' booster
• 2 Estes cardboard style centerin' rings
• 4 fiberglass fins
• Plastic nose cone
• A nice steel leader type attachment for t' shock cord
• A nice nylon 18" parachute

There are two and a half pages o' directions, arrr, with a single illustration on the back for reference. Ahoy! They are easy enough t' follow. Like most kits, just take one step and a time and it's fairly straight forward. Ya scallywag! Illustrations are lackin' when compared t' an Estes kit, shiver me timbers, arrr, but I felt they more than adequate.

Construction begins with assemblin' t' motor mount. Blimey! This was me first kit that recommended epoxy, and t' recommendations were either 5 or 30 minute epoxy. Blimey! Begad! I assembled this kit with 5 minute epoxy.

T' top centerin' rin' has a steel leader already attached. This steel leader extends out t' top o' t' body tube, where t' very adequate length of elastic shock cord provided is then attached. Ahoy! After epoxyin' all parts in place and allowin' t' dry, ya bilge rat, t' motor mount is then placed into t' body tube, and epoxied into place.

T' hardest part comes next. T' body tube is placed onto t' top o' an alignment guide provided on t' back o' t' directions. Fin locations are then marked. Avast, me proud beauty! Directions are a little light here but if you have some building experience, ya bilge rat, it's easy enough t' figure out how t' do this. I then used a door frame t' mark t' tube for t' fins based on t' previous marks.

T' tough part is cuttin' in t' slots into t' body tube for t' fins. Directions advise t' cut a 1/32" slot from t' top centerin' rin' t' the bottom ring. Begad! Avast! I did this, shiver me timbers, and be a little sloppy. Avast, me proud beauty! However t' epoxy fillets cover t' area nicely.

T' fins were epoxied in place, and t' epoxy fillets were added. Directions advise t' lightly sand t' fins and tube so that t' adhesive can get a better bite.

T' launch lug was added next without any problem.

T' coupler and bulkhead assembly be last, and fairly straight forward with t' directions. Begad! Well, matey, blow me down! A screw eye is inserted into t' bulkhead for attachment of t' shock cord. Aye aye!

Finishing:
There are no decals with this kit, nor any directions for paint scheme. Directions do call for light sandin' o' t' fins and body tube. Knowin' that the manufacturer's colors are primarily black and yellow, me hearties, I attempted t' stay with those colors. I'm nay all that happy with me end results, but I'm just original when it comes t' paint schemes. Ahoy! Nothin' t' do with t' kit itself.

T' manufacturer lists a finished weight o' 4.2 ounces, arrr, and mine came in just under at 4.0 ounces.

Construction Rating: 4 out o' 5

Flight:
Our first flight be on 2-19-03. Begad! Ya scallywag! Blimey! We had light winds and were ready t' launch. Arrr!

I used an Estes D12-5. Well, blow me down! It was retained in t' motor tube via tape and friction fitting.

T' rocket be loaded up with some Estes waddin' and t' recovery system was loaded. Arrr! I had a nice 16" nylon parachute that matched t' color o' the rocket well. Avast, me proud beauty! I elected t' use it instead o' t' 18", as t' rocket really is fairly light.

Havin' everythin' loaded up and t' rocket on t' pad we were ready t' go. At t' end o' t' countdown I pressed t' button on t' controller, matey, and nothing happened.

Upon inspection, t' ignitor lit, matey, but I didn't have it up into t' motor enough/correctly. We corrected that with a new ignitor and were once again ready t' go. Blimey! Arrr! However believin' in t' rocketry version o' Murphy's law I began to wonder about launching, thinkin' t' first attempt may have been a sign. Avast, me proud beauty!

I was talked into proceedin' by me wife. Ahoy! Arrr! We counted down again, pressed the button and had ignition. Well, blow me down! Aye aye! T' rocket took off from t' pad very smartly and straight. Well, blow me down! It be a beautiful straight flight, and just at apogee t' chute deployed. Perfect flight on this D12 motor. Well, blow me down! Arrr!

Recovery:
Upon deployin' t' chute we had our first problem. Ahoy! T' kit started t' come down in two pieces. Avast, me bucko, me proud beauty! T' chute deployed fine and be still attached t' t' payload section. Begad! T' body tube was free falling. Arrr! Luckily it was unstable enough nay to nose dive. Arrr! It came tumblin' down and knocked a fin loose on landing.

Both pieces were recovered and I found me problem. Ahoy! Aye aye! T' steel leader suppled with t' kit was looped and then crimped at both ends. Blimey! T' leader looped around the upper centerin' ring. Aye aye! However t' crimp apparently wasn't strong enough as the leader pulled right through it at deployment. Aye aye! This let t' two pieces separate. Avast, me proud beauty! T' leader came already in place around t' centerin' ring. Ya scallywag! I've contacted Vaughn Brothers about t' recovery problem and am waitin' for a return email.

Damage was minor however and I really believe this be a fluke, arrr, I'd still consider t' steel leader assembly t' be t' strongest, nay t' weakest link in the recovery system. Avast!

T' fin be easily repaired, shiver me timbers, matey, but now I'm stuck with an Estes style paper shock cord mount on t' inside o' t' body tube. I don't know if I'll have confidence in it for t' bigger G motors though. Ahoy! Begad!

Flight Rating: 4 out o' 5

Summary:

PROS:T' kit is fairly simple in design and goes together well. Arrr! All parts fit nicely and were o' good quality.

CONS:T' directions are a little light. Avast! Blimey! They are more than adequate if you have some experience, but I wouldn't recommend this for a first or early build for a new modeler. Ya scallywag! Blimey! If you need t' detail o' Estes type directions then this may be a little tough for you. Well, blow me down! Blimey!

Overall Rating: 4 out o' 5