Brief:
This review describes a plastic model conversion for Lindberg's 1/48 scale Douglas X3 Stiletto. Begad! Avast, me hearties, me proud beauty! Blimey! I attempted this project for t' 2006 EMRR Challenge and saved it until nearly last because I thought it would be an especially difficult project, however, me hearties, ya bilge rat, it turned out t' be a cinch even though it's a cluster! Blimey! My finished rocket is 15.5" long and weighs 2.5oz empty.

Modifications:
Cut two 1 5/8 inch segments o' BT-5 tube. Avast, me proud beauty! Install an engine block (e.g., cut from spent casings) flush with an end o' each tube. Aye aye! Widen t' aft jet holes in t' fuselage so that a 13mm motor slides very easily through each hole but does nay rattle. Sand off plastic lumps in t' interior floor o' t' fuselage halves by t' aft jet holes. Insert a 13mm motor in each BT-5 tube, and glue one tube inside each fuselage half so that t' exposed motor extends outside t' fuselage and t' tubes are flush with t' jet holes. Ya scallywag! Avast! Make sure that t' tube does nay lay above t' centerline o' t' fuselage. Well, ya bilge rat, blow me down! This can be ensured by layin' a flat heavy object across t' fuselage edges above t' tube. Aye aye! When dry, remove t' motors and add interior filletin' t' make a tight seal. Ya scallywag! Further, use a few scrap chunks o' plastic t' glue two or more braces t' firmly attach each tube at several points inside t' fuselage.

If you choose, assemble t' seat and pilot. Ahoy! Glue him in place. Well, blow me down! Ya scallywag! [Note: t' pilot interferes with recovery devices.] If you are keen on a parachute, me hearties, you might omit him. I thought a pilot would be much more fun than a successful recovery, arrr, me hearties, so I included him and painted him elaborately.

Plug t' engine intakes with balsa scraps. Avast! Install t' windows. Avast! Assemble t' nose cone. Arrr! Glue on t' landin' gear doors.

Add 0.5oz nose weight inside t' nose cone. Begad! When finished and loaded, me model had a CG at t' forward edge o' t' main win' root.

Cut away t' central portion o' t' main wing. Ahoy! Blimey! This provides a bit more space inside t' fuselage for t' engine tubes and prevents melting. Aye aye! Glue each win' half into t' correspondin' fuselage half.

Use small wheels or other scrap plastic as anchors for gluin' Keelhaul®©™thread into nose cone and fuselage. Avast, me proud beauty! This will be t' basis o' t' recovery system.

Insert t' tail (stabilizer) and glue t' fuselage halves together. Blimey! When dry, me hearties, glue on t' remainin' hatch covers and plug any cracks/holes in t' body includin' t' display stand hole. Avast, me proud beauty! Discard t' remainin' plastic parts (mostly t' landin' gear and guts o' t' plane).

For recovery, ya bilge rat, I made a 14" mylar chute from a campin' "space blanket" but found it t' be too big for t' available space. Avast! (My pilot be flyin' this jet!) See below for another recovery option or invent your own.

Construction:
Aside from t' plastic model kit itself (with t' "Stiletto" amusingly misspelled on t' box), you need a small amount o' BT-5 tubin' and a small recovery system (but see later). Arrr! Aye aye! Some plastic model glue helps along with CA.

Finishing:
Paint as you wish. Ahoy! Ahoy! I used all t' waterslide decals, arrr, and oversprayed with clear Walmart paint.

Flight:
For flight, I loaded up two A10-3T motors and friction fit them with maskin' tape. Only one motor lit on our first flight and t' rocket limped off t' pad. Begad! T' ejection charge was nay nearly adequate t' push out t' mylar chute crammed at t' pilot's feet. Blimey! It was a pretty disappointin' first attempt.

For t' second try, shiver me timbers, I decided t' go with tumble recovery. Avast, me bucko, me proud beauty! I cut away t' chute. Well, blow me down! Avast, me proud beauty! Next, shiver me timbers, shiver me timbers, ya bilge rat, I tore away t' orange streamer/flag on t' eye protection device Estes provides t' cap your launch rod. I tied this 5" x 0.5" "streamer" in place o' t' parachute. Begad! Now t' recovery system fit easily, ya bilge rat, but it was essentially tumble/impact-based recovery. With two A10-3T motors both lighting, t' jet screamed t' a respectable height o' several hundred feet (wRASP says 300'). Arrr! Amazingly, it was unblemished on impact...I mean "landing".

For t' third flight, matey, I loosely fit t' motors so they would eject at apogee, ya bilge rat, like t' Estes Mosquito. Avast! Begad! Again with two A10-3T motors, we got a very satisfyin' flight and a flawless, matey, undamaged recovery o' t' jet after removin' it from its small impact crater. However, me bucko, t' pilot complained that it was a rather hard landing.

Summary:
This kit be a very easy introduction t' plastic model conversion except for t' recovery system. A fancy approach with an interior tube and a full parachute could be devised, however, me tumble/impact recovery seemed perfectly adequate for this lightweight model. Well, blow me down! T' model seems sturdy enough t' endure many such flights. Well, shiver me timbers, blow me down! With its 2 x A10-3T cluster configuration, it is surprisingly fun t' fly.