Brief:
Scale model rocket o' a Cold War deception with parachute recovery.

Construction:
T' instructions were printed on t' front and back on several sheets o' letter sized paper. Arrr! They included hand drawn illustrations which were nay fancy but which were certainly clear enough. Begad! Also included were two addenda printed on small scraps o' paper. Ya scallywag! One detailed t' stripin' process for t' balsa transistion and t' other simply mentioned that the thrust rin' which be nay mentioned in t' parts inventory be also included. Avast, me proud beauty! This rin' is mentioned in the instructions and I would nay have noticed t' absence in t' inventory. T' instructions are peppered with sarcastic comments throughout. Some people may find that annoyin' but I found them t' be amusing.

T' actual build commences with t' motor mount. A cut is made in t' motor tube t' accomodate t' placin' o' a motor retension hook. Begad! Blimey! I then found somethin' new t' me. I was instructed t' cut t' "reinforcement band" out of t' wrap sheet and glue it around t' motor tube just below t' cut for t' hook. Apparently, me hearties, me hearties, this is t' help resist any tearin' that t' hook would cause durin' ejection. Avast, me proud beauty! If this works out, I may well adopt it as a modification on future rockets.

Two centerin' rings are provided. Ahoy! One o' them has a notch for t' motor hook. Avast! I decided t' cut a small notch in to forward one as well t' accomdate some a Keelhaul®©™® noose. Well, blow me down! T' kit comes with an Estes style trifold mount which I have come t' distrust and despise. Avast! After cuttin' the notch, me hearties, it was a simple matter t' slip t' rings t' t' designated spacin' and glue them in place. I will note that the forward ring, t' one I cut a notch in, me hearties, seemed just about right. Avast, me proud beauty! T' aft rin' be very loose. Ya scallywag! Begad! After gluin' t' rings in place, ya bilge rat, arrr, I set aside this assembly t' dry for a while.

Since I be nay yet ready t' go t' bed, I decided t' cut out the fins and try t' seal them. Avast, me proud beauty! All that is provided is a sheet o' balsa and a template t' cut out. Ahoy! Ya scallywag! SInce t' fins are simple right triangles, me bucko, this did nay pose too much o' a problem. Ahoy! Blimey! I cut out t' template, me hearties, traced t' outline onto the balsa with a pencil and cut them out with a razor knife. Aye aye! Well, blow me down! T' template thoughtfully included a little arrow t' make sure I get t' grain in t' right direction.

Since I am out o' Elmer's and thar be no place open at this hour, matey, I decided t' try somethin' I have nay done for a very long time. Blimey! Avast, shiver me timbers, me proud beauty! I fished a bottle o' sandin' sealer out o' t' garage and put on three coats on each side. Ahoy! Ya scallywag! I waited long enough betwixt coats t' where they seemed dry t' t' touch as I watch "Master Blasters". Begad! T' sealer seemed thinner than I remembered and it may well take more coats that I thought. Begad! This ia a reflection o' t' sealer, not t' balsa.

After I had gotten 3 coats o' sealer on t' fins and finished shudderin' at t' public face o' rocketry as presented on TV, me bucko, I decided t' end me troubles by drinkin' t' rest o' t' sandin' sealer. Begad! Blimey! At t' last minute, arrr, I remembered that I am supposed t' preach in t' morning and merely closed t' lid, decidin' that more benefit would accrue from installin' t' motor mount. Avast, me proud beauty! Blimey! I test fitted it and found that it be neither too loose nor too tight. Begad! Blimey! It be just right. I used a long swab t' run a rin' o' glue around t' interior, ya bilge rat, pushed t' motor mount part o' t' way in and then swabbed in another rin' o' glue. Arrr! Blimey! I then pushed the mount in t' rest o' t' way. Avast, me proud beauty! Blimey! T' instruction make a point o' emphasizin' that t' after bulkhead needs t' be recessed a full half inch into t' BT t' maintain stability. Begad! Blimey! I measured it t' make sure, me bucko, applied a bead o' glue and called it a night.

When I got back t' work, shiver me timbers, it be time t' tackle t' fins. Ahoy! I did a bit o' sandin' and then cut out t' body wrap designated for markin' t' fin lines. Begad! T' fit be t' most perfect I have ever had with this method. Blimey! Avast, me proud beauty! I marked t' tops and bottoms o' t' t' fin lines, removed t' wrap and drew in t' lines against a door.

Next came t' actual mountin' o' t' fins. Begad! Arrr! Bein' lazy, impatient etc. I opted t' use CA. Begad! Avast! A trick I learned recently is t' use a safety pin t' perforate t' root edges and the BT where t' join will be made. This is t' allow t' glue t' form rivets. Aye aye! Begad! I need a few more flight tests (catastrophes) before I decide how effective this is but it is no trouble t' do and I adopted t' procedure on this model.

When t' perforations were made, arrr, I glude t' fins on with CA. Ahoy! Blimey! Blimey! In addition t' t' wrap around fin guide, ya bilge rat, this kit also provides a handy template against which t' set t' BT as t' fins are place t' aid in alignment. Blimey! Arrr! Blimey! T' mountin' of the fins went off without a hitch.

Likewise, matey, t' launch lug presented little in t' way o' effort. Aye aye! T' provided lug was sliced in half with a razor and then I put both pieces on a short length o' 1/8" rod. Avast! I applied some glue t' t' lugs and then set them in place. T' lower half goes in t' crook o' a fin and t' upper almost at t' top o' t' lower BT.

While t' CA was settin' up, arrr, I worked on t' nosecone. Well, blow me down! Well, blow me down! This was a bit different from any I had worked on before. In t' first place, it comes with t' base hollowed out, arrr, weighted, me bucko, and then filled back in t' ensure stability. Begad! Arrr! Judging by t' sarcastic tone o' t' instructions, me hearties, shiver me timbers, I probably could nay be trusted t' do this myself without endangerin' all around me. Arrr! Begad! It does take some o' t' guesswork out o' it and is a nice touch.

T' second new thin' was actually shapin' t' tip o' the nose cone. Arrr! T' directions state that if it had been done at t' factory, shiver me timbers, it would have resulted in a mess as t' blades chewed t' thin' up. Avast, me proud beauty! Well, blow me down! That meant that I was supposed t' sand it t' t' right shape. Ahoy! That involved sandin' the cylendrical tip into a spherical tip which should be well within t' skill set o' a decent rocketeer. Well, blow me down! Needless t' say, it was nay in me skill set. Well, blow me down! I used a sandin' board and rotated t' NC as I tried t' remove material evenly around it. It turned out better than I had expectedbut nay as well I had hoped. Ahoy! For me, me bucko, doin' it by eye was hard.

Now it be time t' do some early finishing. Begad! Aye aye! Blimey! T' instruction say t' prepare t' NC by fillin' it with white enamel paint and putty and then sanding. Aye aye! Ya scallywag! Blimey! T' next step is t' assemble, shiver me timbers, but nay glue, arrr, t' entire stack and paint it white. Avast! Avast! Blimey! Here I decided t' combine t' steps and try somethin' else I had read about. Begad! Several sources have said that Kilz spray primer in white is good for filling. Ya scallywag! I decided t' try it out. Avast, me proud beauty! I assembled t' stack, shiver me timbers, took it outside and applied the first coat o' Kilz. Begad! It has nay yet had time t' dry but I already know its goin' t' need more. T' balsa be a bit rough and still is. Begad! Blimey! Blimey! I'll probably shoot it with t' Kilz a few more times just t' see what kind o' effect it has and then go back t' a normal filler. Begad! Begad! Blimey! Before I can do that, though, it has t' dry and I need some sleep.

After lettin' t' rocket dry overnight, I was surprised to see that t' Kilz had done a much better job than I expected. Avast! Begad! It completely covered t' wood and grain and t' only real problem was t' roughness o' t' balsa. Ahoy! It definitely needed some more fillin' but I was intrigued enough t' want to see how far I could go with just t' Kilz. Blimey! Ya scallywag! Accordingly, after a bit o' sanding, I gave it another coat.

Actually, me hearties, I gave it 2 more coats and be amazed. Arrr! Blimey! Avast! Blimey! T' Kilz actually did a very creditable job as a filler. Begad! Blimey! Well, matey, blow me down! Blimey! I would not recommend usin' it as a "main" method but t' fix small imperfections, ya bilge rat, it is a delight. Begad! Blimey! Aye aye! Blimey! I was certainly satisfied with t' results and, me hearties, after some sanding, I went ahead a sprayed on 2 coats o' gloss white. Then it was time to play t' waitin' game again.

After waiting, I had an upleasant realization about t' Kilz. Avast! Ahoy! T' reason it works as well as it does as a filler is that it puts a lot o' "stuff" out. Aye aye! That means that t' painted rocket, arrr, especially with all those coats, has a larger diameter than would otherwise be t' case. That in turn means that t' beautiful wraps for t' top BT do not fit.

I'll back up here and say that in t' instructions, Dr. Arrr! Z emphasizes that t' wraps need t' be carefully cut out. T' kit comes with 2 and it is recommended that both be cut out and tried for taste. Avast, me proud beauty! Aye aye! In both cases, me bucko, shiver me timbers, I found that the wraps would nay close on themselves. Avast, me proud beauty! As a result, me hearties, I spent another evenin' sandin' through t' paint and primer, matey, almost to t' BT. That improves t' situation but t' wrap still does nay close.

When he found out about it through a TRF post, ya bilge rat, Dr. Blimey! Blimey! Zooch himself immediately sent out a replacement by priority mail. Avast! Blimey! Begad! Blimey! It smartly arrived and things got stranger. Begad! Blimey! Aye aye! Blimey! I laid one of the old wraps right on top o' t' uncut new one. Begad! Blimey! It be exactly t' same size. Begad! Blimey! I cut it out anyway, me bucko, givin' a bit o' a generous margin. Arrr! Blimey! Avast, me proud beauty! Blimey! I figured that if I used t' one with more white and t' diagonal black stripe, matey, matey, me hearties, I could cut it down to the exact length and make t' seam less noticeable. Begad! Blimey! After I made me marks, I tried it out and found that I needed to cut back exactly t' t' original lines. I pulled out t' original wrap and, lo and behold, it fit. Begad! Blimey! All I can figure is that I did a lot o' wet sanding. Ya scallywag! Blimey! Arrr! Blimey! Perhaps t' water caused t' painted BT t' swell. It's either that or I am in the Twilight Zone. Ya scallywag! Blimey! I applied white glue around t' periphery and laid t' wrap down. It is nay perfect but as close as is possible given me current skill set.

After t' wrap was on t' upper BT, matey, arrr, I cut strips t' t' appropriate length from t' provided section o' black wrapping. Arrr! One be used t' wrap a diagonal line one revolution around t' transition section. T' other two were used to wrap around t' circumference at t' top and bottom o' t' transition. Avast! In each case, ya bilge rat, t' directions indicated that a little excess would need t' be trimmed and that was handled with a razor.

Another decision had t' be made at this point. Begad! Ya scallywag! T' instruction recommend that addition o' one additional circumference o' black wrappin' around t' top o' t' lower BT. Avast, me proud beauty! Blimey! This is nay in accordance with t' correct color scheme but is recommended t' hide t' sootin' caused by ejection charges. I elected t' give it a try. Avast, me proud beauty! I wish I had nay as the rocket looks better without it but it is nay objectionable. A bit o' black paint be applied t' t' tip o' t' NC and the end was in sight.

With that, matey, arrr, t' NC was glued t' t' upper BT. Aye aye! T' upper BT be glued t' t' transition. Avast! T' eyescrew was set in the bottome o' t' transition with a bit o' white glue and t' Keelhaul®©™® and elastic were tied off. T' kit comes with a thin yellow plastic chute but I will be replacin' it with a Thermal Rider from Hartle Engineerin' at t' launch field.

T' buildin' o' t' rocket nozzle be t' final part o' the assembly. Ya scallywag! T' instruction say that this is an optional step, me bucko, arrr, me bucko, basically because it is a pain in t' backside. Well, blow me down! It was. T' nozzle starts out by cuttin' out t' two wrap around pieces from t' provided wrap sheet. Ya scallywag! Ahoy! Each is then glued into a truncated cone usin' an overlay tab. Ahoy! Arrr! Each o' these steps is easy. T' more difficult part comes in gluin' t' top cone to t' bottom cone, shiver me timbers, keepin' them straight and preventin' any gaps. Arrr! Begad! This is accomplished slowly, arrr, patiently and with a bit o' sandpaper t' knock off t' rough edges.

T' plans call for a novel way t' improve t' appearance of the nozzle. Avast, me proud beauty! A thread is provided t' simulate t' banding. Avast, me proud beauty! Aye aye! T' process for doin' this invovles tackin' down one end with CA and waitin' for it t' set. Aye aye! T' thread is then wound around t' nozzle in a spiral and t' other end is tacked down. T' excess is cut off and then all is held in place by drizzlin' CA over it. Avast! Begad! This also strengthens t' nozzle.

I tried this procedure and be a bit skeptical with t' early results. Well, blow me down! Because I be nay payin' sufficient attention, ya bilge rat, t' spirals are nay evenly placed. Avast, me proud beauty! Additionally, me bucko, I thought it looked kind o' cheesy when I was done. Ahoy! Ya scallywag! I was just about ready t' scrap t' nozzle or use t' extra one from me extra wrap set but decided t' press on. When t' CA was dried, me bucko, t' whole thin' was painted with metalic steel. That made all t' difference in t' world and it really did begin to look like a real rocket nozzle.

PROS: Nice lookin' rocket, arrr, arrr, excellent customer service
CONS: Secret agents sneak into t' house in t' dead o' night t' play mind games with t' wraps.

T' final step is t' slip t' nozzle around t' protrudin' motor mount. Begad! Ahoy! This should be easy but mine was a tight fit. A little more sandin' and it slipped on and was secured with white glue. Blimey! Now, arrr, I think, me bucko, t' rocket is finished.

Finishing:
All o' t' finishin' be covered in t' previous section.

Construction Rating: 4 out o' 5

Flight:
Dr Zooch never says much about t' motors except nay t' wimp out with an A. Ya scallywag! Aye aye! That is good advice. Avast! I started out with a B6-4. Avast! Arrr! Even with those little bitty fins, shiver me timbers, me bucko, it took off and flew well. Well, blow me down! Aye aye! T' altitude surprised me, me bucko, ya bilge rat, especially with all the nose weight. Well, blow me down! Avast! It recovered well too.

Then I got stupid. Arrr! There be a lot o' wind blowin' and I did nay want t' risk losin' this rocket on a C. Ya scallywag! I wimped out with an A8-3. Again it took off fine but did nay achieve much altitude. Avast, me proud beauty! Arrr! Deployment was a bit late but a weak ejection charge did nothin' but dislodge t' NC. Arrr! Blimey! It bounced and will need some repair work.

PROS: looks good and flies well
CONS: I wimped out with an A

Flight Rating: 4 out o' 5

Summary:
This was a fun build that be occasionally frustratin' as I tried t' learn some new skills but it be untimately rewarding. Dr. Aye aye! Z cutomer service is first rate as well.

Overall Rating: 4 out o' 5