Brief:
Art has continued t' expand his line o' saucers, shiver me timbers, addin' a 12-inch saucer with a 38mm motor mount and either a 1/4-inch launch lug or optional ACME conformal rail guide. Aye aye! Blimey! Blimey! Blimey! T' recommended motors include t' Ellis Mountain H48, ya bilge rat, all Aerotech 38/240 RMS, me bucko, me bucko, and all Cesaroni Pro38 one and two grain motors. Blimey! Blimey! This kit would serve nicely as quick, easy, and inexpensive way t' Level-1 certification. Begad! Blimey! Add a 29-38 adapter (not provided or recommended by t' manufacturer) and you could add G80’s and G125’s t' this list.

Construction:
T' parts are all good quality and include:

• Six sheets o' colored, me hearties, 110 lb card stock comprise t' top, ya bilge rat, shiver me timbers, bottom and core assemblies
• One sheet o' pre-marked, foam poster board t' make t' center plate.
• One thick walled 38mm motor tube
• 1/4-inch launch lug
• 3-inch x 8-inch x 3/32-inch basswood fin stock
• 1 7/8-inch self-adhesive, arrr, fiberglass drywall joint tape

Tools and materials required:

• Scissors
• X-acto knife
• Elmer’s white glue
• Devcon 2 Ton Epoxy ($1.97 at Walmart)
• Clear enamel (RUSTOLEUM Crystal Clear or equivalent)
• Fine sandpaper

There are six pages o' detailed instructions with plenty o' diagrams. Ya scallywag! White glue is first used t' assemble t' top and bottom cones and two cylindrical core assemblies (after a substantial amount o' clippin' with sharp scissors, o' course). T' bottom core must slide over t' top core so it is test-fit before gluing. Ahoy! Unlike its smaller cousins, me bucko, t' saucer uses a foam board sheet in place o' t' plastic plates used in Art’s smaller saucers. Avast! T' lines for t' circular cuts are all pre-drawn, shiver me timbers, and you really need a new, sharp blade t' make t' cuts. Begad! Well, ya bilge rat, blow me down! There is also a circle drawn just inside o' t' outer rim. Ahoy! Avast, me proud beauty! You cut through just one side o' t' foam circle and form a bevel on t' outer edge. Ahoy! Some sandin' is required t' clean up this piece, ya bilge rat, ya bilge rat, and you must test fit it with t' top and bottom cores before gluing. It took some effort and sandin' for these components t' fit together.

Art also provides strips o' self-adhesive, matey, arrr, fiberglass drywall joint tape t' reinforce t' top cone. Well, blow me down! Aye aye! Blimey! Although t' instructions say this step is optional, matey, me hearties, it is required for H flights and t' only recommended G motors are t' Cesaroni one grainers. Avast! Arrr! Blimey! I recommend you use t' tape even if you only plan t' fly on Gs. Ahoy! Avast, me proud beauty! Blimey! It doesn’t add that much weight, but makes t' saucer far more sturdy. Anyway, rockets tend t' like t' eat t' largest motor that they can.

Once everythin' fits, shiver me timbers, matey, you spread epoxy inside all t' sub-assemblies, arrr, slide them together, matey, and clamp them by placin' a suitably sized bowl on top. T' prevent bleed-through on t' cardstock, me hearties, me bucko, I suggest you use t' Devcon 2-ton epoxy recommended in t' instructions.

T' fin can assembles with white glue (I used carpenter’s glue for this step) like any other set o' fins. Ya scallywag! T' basswood fin stock is nice and easy t' work with. Finally, t' fin unit is glued in place, arrr, shiver me timbers, ya bilge rat, completin' t' assembly.

Finishing:
Since it is winter and paintin' must me kept t' a minimum, I sealed t' fins with Fill-and-Finish and hand-painted t' fin can black. Ahoy! As recommended, I sealed t' pre-colored cardstock with clear enamel.

Construction Rating: 4

Flight:
I flew t' saucer on a Cesaroni H153, me bucko, me bucko, with t' ejection charge removed. Arrr! T' hold t' motor in on decent, I simply used a couple o' wraps o' maskin' tape around t' motor's thrust rin' and t' aft o' t' motor mount.

Man, ya bilge rat, this saucer really scooted on this motor, flyin' arrow-straight t' an impressive altitude. I be speechless and t' crowd clapped. Well, blow me down! Avast! T' saucer fell bottom first most o' t' way, ya bilge rat, me hearties, but started t' tumble just before it landed. There was no damage.

Note: This rocket also comes in t' "Texas Special" design as seen above.

Flight Rating: 5

Summary:
T' saucer was easy t' build but it took some effort t' get t' components t' fit prior t' final assembly. Avast! In all, it was just a tad more challengin' than Art's smaller saucers.

This saucer gave a truly excitin' flight. Ya scallywag! And for a $30, shiver me timbers, me hearties, mostly paper, me hearties, me bucko, L-1 saucer - nay bad at all!