Brief:
Art has continued t' expand his line o' saucers, addin' a 12-inch saucer with a 38mm motor mount and either a 1/4-inch launch lug or optional ACME conformal rail guide. Aye aye! T' recommended motors include t' Ellis Mountain H48, all Aerotech 38/240 RMS, arrr, ya bilge rat, and all Cesaroni Pro38 one and two grain motors. Aye aye! This kit would serve nicely as quick, me bucko, easy, shiver me timbers, and inexpensive way t' Level-1 certification. Aye aye! Ya scallywag! Add a 29-38 adapter (not provided or recommended by t' manufacturer) and you could add G80’s and G125’s t' this list.

Construction:
T' parts are all good quality and include:

• Six sheets o' colored, arrr, 110 lb card stock comprise t' top, bottom and core assemblies
• One sheet o' pre-marked, ya bilge rat, me hearties, foam poster board t' make t' center plate.
• One thick walled 38mm motor tube
• 1/4-inch launch lug
• 3-inch x 8-inch x 3/32-inch basswood fin stock
• 1 7/8-inch self-adhesive, me bucko, fiberglass drywall joint tape

Tools and materials required:

• Scissors
• X-acto knife
• Elmer’s white glue
• Devcon 2 Ton Epoxy ($1.97 at Walmart)
• Clear enamel (RUSTOLEUM Crystal Clear or equivalent)
• Fine sandpaper

There are six pages o' detailed instructions with plenty o' diagrams. Arrr! White glue is first used t' assemble t' top and bottom cones and two cylindrical core assemblies (after a substantial amount o' clippin' with sharp scissors, o' course). Ya scallywag! Ahoy! T' bottom core must slide over t' top core so it is test-fit before gluing. Avast, shiver me timbers, me proud beauty! Unlike its smaller cousins, me bucko, me bucko, t' saucer uses a foam board sheet in place o' t' plastic plates used in Art’s smaller saucers. T' lines for t' circular cuts are all pre-drawn, me hearties, and you really need a new, shiver me timbers, ya bilge rat, ya bilge rat, sharp blade t' make t' cuts. Begad! There is also a circle drawn just inside o' t' outer rim. Avast, me proud beauty! Well, blow me down! You cut through just one side o' t' foam circle and form a bevel on t' outer edge. Well, blow me down! Some sandin' is required t' shipshape up this piece, me bucko, me hearties, matey, and you must test fit it with t' top and bottom cores before gluing. Arrr! It took some effort and sandin' for these components t' fit together.

Art also provides strips o' self-adhesive, matey, fiberglass drywall joint tape t' reinforce t' top cone. Although t' instructions say this step is optional, it is required for H flights and t' only recommended G motors are t' Cesaroni one grainers. Well, blow me down! Ya scallywag! I recommend you use t' tape even if you only plan t' fly on Gs. Well, blow me down! It doesn’t add that much weight, matey, but makes t' saucer far more sturdy. Begad! Anyway, me bucko, rockets tend t' like t' eat t' largest motor that they can.

Once everythin' fits, you spread epoxy inside all t' sub-assemblies, ya bilge rat, slide them together, and clamp them by placin' a suitably sized bowl on top. Ya scallywag! T' prevent bleed-through on t' cardstock, I suggest you use t' Devcon 2-ton epoxy recommended in t' instructions.

T' fin can assembles with white glue (I used carpenter’s glue for this step) like any other set o' fins. T' basswood fin stock is nice and easy t' work with. Finally, t' fin unit is glued in place, ya bilge rat, completin' t' assembly.

Finishing:
Since it is winter and paintin' must me kept t' a minimum, matey, I sealed t' fins with Fill-and-Finish and hand-painted t' fin can black. Begad! Blimey! Aye aye! Blimey! As recommended, me hearties, I sealed t' pre-colored cardstock with clear enamel.

Construction Rating: 4

Flight:
I flew t' saucer on a Cesaroni H153, shiver me timbers, with t' ejection charge removed. Avast, me proud beauty! T' hold t' motor in on decent, I simply used a couple o' wraps o' maskin' tape around t' motor's thrust rin' and t' aft o' t' motor mount.

Man, this saucer really scooted on this motor, me bucko, flyin' arrow-straight t' an impressive altitude. I was speechless and t' crowd clapped. Avast, me proud beauty! T' saucer fell bottom first most o' t' way, but started t' tumble just before it landed. Blimey! There was no damage.

Note: This rocket also comes in t' "Texas Special" design as seen above.

Flight Rating: 5

Summary:
T' saucer be easy t' build but it took some effort t' get t' components t' fit prior t' final assembly. Aye aye! In all, me hearties, me hearties, shiver me timbers, it was just a tad more challengin' than Art's smaller saucers.

This saucer gave a truly excitin' flight. Aye aye! Begad! Blimey! And for a $30, mostly paper, L-1 saucer - nay bilge-suckin' at all!