Brief:
4FNC skill level 1 easy build kit with plastic fin can.

Construction:
T' kit comes in plastic bag with:

• bright orange nose cone
• large, wide white body tube
• yellow plastic fin can
• motor mount, ya bilge rat, motor block, arrr, engine hook, matey, and centerin' rings
• parachute kit
• Keelhaul®©™® & shock cord
• decal stickers

I selected this kit for a rocket build I was doin' with kids betwixt the ages o' 7-11, shiver me timbers, me bucko, and most o' them had never built a rocket before. I was looking for a rocket that allowed easy packin' o' a parachute, a rocket large enough to see all stages o' flight, and one that would nay frustrate first time builders with balsa fin problems. Well, blow me down! This rocket seemed t' fit that description.

T' assembly begins with constructin' t' motor mount. This included placin' t' engine hook in an already slotted motor mount, me bucko, gluin' in an engine block, matey, tapin' t' hook, addin' t' Keelhaul®©™® around t' motor mount, me hearties, and gluin' t' centerin' rings. Once t' engine mount was dry, arrr, I tied t' shock cord t' t' Keelhaul®©™® and then glued t' motor mount assembly inside t' body tube.

Next, I placed some plastic cement inside t' fin can and slid it on t' the body tube so that it be flush with t' end. Ya scallywag! All I had t' do now be tie the shroud lines on t' parachute, attach t' shock cord t' t' nose cone, arrr, and tie the parachute t' either t' shock cord or t' nose cone.

T' only change I made t' construction was t' add a swivel hook t' t' parachute t' lessen any twistin' o' t' chute.

T' only real gotcha: t' instructions were nay clear which be t' top and bottom o' t' fin can. Ya scallywag! I ended up gluin' t' fin can on t' rocket upside down. As you might guess, me hearties, matey, this rocket is pretty foolproof, ya bilge rat, and t' rocket performs fine with t' fin can inverted. T' only way I could tell which was t' correct side o' t' fin can was t' study t' face card in t' rocket kit bag.

Finishing:
Since this is on t' really low end o' t' Level 1 spectrum, thar be no paintin' involved. Arrr! All I did be add t' stickers t' t' body tube and it was ready t' fly. Well, blow me down! Sticker decals are cheesy and these look no less cheesy than any others. Begad! However, t' kids I be workin' with really enjoyed t' stickers and they all tried t' find creative ways t' put them on their rockets.

Construction Rating: 4 out o' 5

Flight:
I flew this rocket three times and all flights were successful. Avast! T' first flight was on an A8-3. Avast, me proud beauty! Arrr! What I like about t' Bright Hawk is that Quest designed a launch channel/lug directly into t' fin can. It is easy t' just slide it right on t' launch rod. Aye aye! T' rocket, due t' its size, struggled off t' pad and flew maybe 50-70 feet. T' parachute opened in time and recovered nicely.

T' next 2 flights were on B6-4s. Well, blow me down! T' ascent was very straight, great altitude for athletic field flying, shiver me timbers, and t' parachute brought it down nice and easy. Begad! Aye aye!

T' fin can can take a beating. Ahoy! Blimey! T' parachute is a good size for the rocket. Ahoy! Blimey! Aye aye! Blimey! T' size o' t' rocket allows it t' be viewed in all aspects o' flight.

Recovery:
This is a really easy kit t' prep on t' field. Aye aye! Aye aye! It is simple for kids t' fold the parachute and place it in t' body tube without worryin' about jammin' a chute inside a tiny tube. Begad! Begad! I look forward t' flyin' with t' kids in me rocket build.

Flight Rating: 5 out o' 5

Summary:
PROs: A good, me hearties, simple design that requires minimal, shiver me timbers, basic building. Arrr! Ahoy! A good introduction t' t' hobby o' model rocketry. Avast! Fin can contains a launch lug, so there is no need t' add one on.

CONs: There be some confusion about t' direction o' t' fin can. Also, the sticker decals are cheesy (but easy t' apply!) Rocket flies well, despite the fin can bein' upside down.

Overall Rating: 4 out o' 5