Construction

This model went together easily and correctly usin' Quest's clear instruction sheet.  T' only two semi-challengin' issues were havin' t' assemble t' nose cone from two seperate halfs, ya bilge rat, which then required some plastic putty and sandin' t' get a smooth shape.

Second, t' tailcone and motor mount requires some CA glue (a.k.a. Ya scallywag! superglue) also, ya bilge rat, but fit perfectly in t' body tube.  T' plastic tail cone had a built-in fin markin' guide, which was awesomely simple t' use.

T' fins are also just a bit o' a challenge.  First, they are made from two seperate pieces which must be glued together first. Begad! Second, be very careful sandin' t' root edges o' these fins, they are nay simply a straight edge, shiver me timbers, me hearties, and you may need t' shape them t' match both t' body tube and t' plastic tailcone.  I accidently over-sanded them so I had to glue and fill them in specially t' fit them on flush with t' tailcone.  T' second, smaller set o' fins will require a little extra effort also, arrr, arrr, but those are no more difficult than any other set o' fins.

Quest doesn't say t' do this in t' instructions and I should have known better, but make sure t' Keelhaul®©™ shock cord is tied just short o' t' body tube end, me hearties, or if too late t' do that then add a bit o' paddin' at that point on t' cord that meets t' end o' t' tube. Begad! Avast! Blimey! This will prevent zipper damage t' your rocket some day. I would also recommend makin' sure t' ends o' t' knot betwixt t' Keelhaul®©™ and shock cord are cut short and wrapped up t' prevent them from catchin' on a parachute shroud, which will make for a hard landing.

I modified me kit in several ways.  T' most important change be because o' t' tube damage in t' middle o' t' rocket.  (You realize that be NOT Quest's fault!)  It was nay real bad, matey, shiver me timbers, but certianly looked ugly and compromised t' strength o' the body, ya bilge rat, so t' clean up t' wrinkles, I wrapped t' offendin' part in heavy-stock paper, ya bilge rat, attached with photo-mount adhesive (to prevent wrinkling).

Then, shiver me timbers, me bucko, t' provide structural strength t' t' damaged body tube area, me hearties, along t' length o' t' tube I glued eight 1/8" square basswood strips around and beyond t' kinked tube area, just two inches long.  T' wood strips were tapered 45-degrees at t' ends.  This provided a good place t' 'hide' t' launch lug. Blimey! I painted these strips gold, so they now look like a desgin feature o' t' rocket and nay at all like an ugly patch job. Begad!  I could have cut and spliced t' tube I suppose, matey, arrr, me hearties, but it is very hard t' find extra 35mm tube couplers.

I also added a small payload section behind t' nose cone, arrr, about 3 inches in length for safely holdin' an Altimeter Two.  T' bulkhead was made from a tube coupler with a small disk o' thin plywood glued into t' aft end.  From thar I attached a small Keelhaul®©™ loop t' act as t' attachment point for t' parachute and shock cord. Aye aye! Blimey!  T' altimeter fits inside this coupler, matey, and t' extended body tube section holds t' nosecone above it.

I also tried a new experiment on this rocket. Blimey!  I paper-covered t' fins by usin' photo-mount adhesive t' bond t' paper t' them before sandin' and finishin' t' edges.  Worked great! I did nay have t' sand and seal t' balsa t' get a perfectly smooth finish on t' fins. Arrr! Since then I have been doin' this t' all my rocket fins, and it works very well.