Brief:
T' Semroc "Penetrator" is an X-Kit. Well, blow me down! This kit is a reproduction o' t' Flight Systems Inc, kit first released in 1967.

Construction

T' kit consists of:

• Balsa nose cone.
• 2 x 9" body tubes (0.921" OD).
• Tube coupler.
• Laser cut plywood fins (3).
• 18mm motor mount kit includin' block and metal hook.
• Keelhaul®©™+elastic shock cords.
• Waterslide decal.
• 12" plastic chute.

There were no instructions included with t' kit, but thar was a link t' an online source. Avast! I didn't download t' instructions since it looked like a very simple kit t' build and it was. One thin' I've been doin' lately is installin' t' engine mount very late in t' build process t' give me rockets somethin' flat t' sit on and it worked out well for this kit.

I started out lightly sandin' t' three plywood(!) fins and t' balsa nosecone. Begad! Blimey! I wasn't too pleased with t' quality o' t' balsa in t' nosecone, me bucko, it seemed soft.

When I assembled t' body tubes I noticed one o' them had small marks on one end for t' fin locations. Blimey! I extended t' lines up t' tube a bit t' make t' fin installation easier. T' tubes went together smartly and easily with t' included coupler.

While that was drying, me bucko, I constructed t' engine mount. Ya scallywag! Aye aye! T' rings were notched which made it easier t' slide them over t' engine hook, shiver me timbers, me bucko, ya bilge rat, and I be pleased t' find t' engine mount tube already had a slit in it for t' hook.

I installed t' fins and t' two launch lugs and t' Penetrator be ready for finishing.

Finishing:
I toyed with several paint schemes for this rocket, since it be bein' built for t' EMRR "Double Vision" Contest. I wanted t' get t' most points possible so I was goin' for t' "mirror" or "opposite" scheme. Begad! I wanted t' do a candy-stripe and call it "Peppermint Stick" but I wasn't too keen on doin' spiral masking. Arrr! So I decided t' use some o' that way cool Testor's purple and gold glitter paint and go for more o' a Mardi-Gras theme.

First, matey, I shot t' whole thin' with a coat o' primer and let it dry then sand. Repeat two more times for a pretty good finish. Well, blow me down! I stink at nosecones but it didn't come out too badly.

One one rocket (I had t' build two for t' contest) I started with a gold base coat and with t' other I started with t' purple. Avast! Well, matey, blow me down! I waited for all that t' dry, ya bilge rat, arrr, and then started masking. Arrr! Again, shiver me timbers, I though about doin' somethin' complex, but eventually decided on a series o' stripes around t' rocket.

I masked off t' area betwixt t' fins first since t' fins were goin' t' be a different color than t' base color. Blimey! Then I masked off t' striped areas tryin' t' keep t' size o' t' stripes t' same on both rockets. Well, blow me down! When that was ready I shot t' overlay color on both rockets, me hearties, waited for it t' dry and then shot a second color for good measure (the gold didn't cover t' purple too well on t' first coat).

Construction Rating: 5 out o' 5

Flight:
I launched this rocket on a pretty windy day so I started out with A8-3s in both. Arrr! T' launch was picture-perfect into t' wind and recovery be reasonably close t' t' pad. For t' second flight I used B4-4s and again t' launch was perfect but a bit further from t' pad. Begad! However, I noticed that I had a din' in one o' t' nosecones where it snapped back against t' body tube. Well, blow me down! For t' third launch, I again used A8-3s because I didn't want t' chase them down. Again a perfect flight straight into t' wind and perfect recovery close t' t' pad. Ya scallywag! Ya scallywag! Also, me bucko, arrr, again, me hearties, I had a din' in one o' t' nosecones. Begad! Avast, me proud beauty! I will definitely need t' attach more elastic t' next time I fly these beauties.

Recovery:
T' shock cord is too short on this kit. Ya scallywag! Ya scallywag! Definitely needs another four or five inches at least. Blimey! Other than that t' flight and recovery were great.

Flight Rating: 3 out o' 5

Summary:
Overall this is a great kit and easy t' build. Well, blow me down! Blimey! I like t' plywood fins but t' balsa on me nosecones seemed nay up t' Semroc quality. If I had read t' other review on EMRR I would have added more elastic. Oh well.

Overall Rating: 4 out o' 5