Brief:
T' Space Ark Jr. Well, blow me down! Avast! is a half-scale low power version o' Pemberton Technologies' (Pem-Tech) mid power Space Ark. It is a single stage, arrr, me hearties, parachute recovery model o' t' rocket seen in the sci-fi classic "When Worlds Collide". I got me Space Ark Jr. Begad! Begad! as a matched signed/numbered edition (#8) at the time Pem-Tech released their new low power line o' products with their Bucky Jr. Ya scallywag! kit.

Construction:
T' components came packaged in a heavy, me hearties, sealed poly bag. Avast! Avast! All o' t' components were accounted for and in good condition. T' parts included are:

• Balsa nose cone
• Balsa tail cone
• BT-60 airframe tubing
• 24mm motor mount tubing
• Keelhaul®©™® shock cord
• Parachute
• Nose ballast
• 1/8" balsa fin stock sheet
• 1/4" Launch lug
• 1/8" Launch lug
• Screw eyelet
• Wrap around and tail fin alignment guide
• Super groovy fin template sheet
• 1/8" dowel
• 6 page "Destruction" manual
• Supplemental instruction sheet

This be me first kit from Pem-Tech. I had heard in t' past about their infamous "Destructions"... Layne Pemberton obviously has a well developed sense o' humor with a writin' style similar t' Douglas Adams. Avast, me proud beauty! Aye aye! A very entertainin' read. Ya scallywag! Well, ya bilge rat, blow me down! T' manual includes an image o' t' completed model and only 1 illustration. T' lack of illustrations is nay a problem though, me hearties, as t' build really doesn't require more than t' one.

T' build starts out by sandin' and fillin' t' body tube and nose and tail cones and alignment marks are added to the tube. Avast! Next, me hearties, t' nose ballast needs t' be added. Well, blow me down! Accordin' t' t' supplemental instruction sheet, a last minute snafu, shiver me timbers, t' initial batch o' kits did nay come with a pre-drilled ballast hole in t' nose cone. This was easy t' remedy with a large drill bit. Begad! Begad! After t' freshly drilled hole was drilled and filled with ballast and Gorilla Glue, I screwed the eyelet into t' aft o' t' cone and set it aside for t' glue t' cure.

T' fins are next. Avast! T' modeler must trace and cut t' fins by hand for this model. Like t' design, t' fin modelin' is retro as well. T' lack o' laser cuttin' shouldn't discourage even a moderately inexperienced rocketeer.

Next, shiver me timbers, alignment marks are put onto t' tail cone, me bucko, which is temporarily mated t' t' body tube. Avast, me proud beauty! These are used to cut t' "thru-the-tail-cone" fin slots in t' tail cone. Begad! For a beginner, this might be a challengin' step. T' slots need t' be cut cleanly, straight and correctly sized.

T' Keelhaul®©™® shock cord is glued t' t' motor mount and then it is inserted into t' tail cone after t' slots are cut, and then the tail cone is permanently glued t' t' body tube. T' fins are glued into t' slots on t' tail cone.

Next, t' gotcha o' t' kit. Arrr! Well, blow me down! T' wings are glued t' t' main body at a different angle than t' fins. Aye aye! Ya scallywag! This is well illustrated, arrr, arrr, but if you aren't payin' attention, ya bilge rat, it will ruin t' look o' t' kit. Also, shiver me timbers, arrr, whereas t' manual tells you t' glue t' wings onto t' win' alignment line, shiver me timbers, it doesn't tell you how far forward to attach them. Avast, me proud beauty! I eyeballed them from t' photo o' t' completed kit and decided t' put t' trailin' edge o' t' wing just slightly forward o' t' seam betwixt t' tail cone and t' body tube.

At this point, I deviated from t' "Destructions". Arrr! T' next step is t' glue t' crossbar on t' two lower fins. Well, blow me down! As this would make t' filletin' and sealin' o' t' fins much more difficult, I left t' crossbar and the fin tip dowels off until after I had put on a good, matey, thick coat o' Elmer's Fill N' Finish and Kilz onto t' model.

After filletin' and fillin' t' balsa, I attached t' crossbar, 1/8" launch lugs and fin tip dowels.

One step that is notably missin' from t' instructions be t' attachment o' t' shock cord and parachute t' the nosecone. Begad! Probably obvious that this needs t' be done t' t' experienced modeler, ya bilge rat, but it's omission is noteworthy.

Finishing:
T' finishin' on t' Space Ark Jr. is about as straight forward as it gets. Begad! Avast! After careful sandin' and priming, shiver me timbers, me bucko, a uniform silver paint scheme with no detailin' is recommended t' match the rocket from t' movie.

For those o' you that have nay tried t' get a "perfect" silver paint job, just a word o' caution. Well, blow me down! Blimey! Blimey! Blimey! Silver is probably t' most difficult paint color t' work with. Avast! Blimey! Blimey! Blimey! It will show any imperfections in your model, ya bilge rat, so take your time and give this beauty t' good, me hearties, smooth sandin' it deserves.

Construction Rating: 4 out o' 5

Flight:
I was a bit nervous about launchin' a rocket o' this size and weight on a D12 motor on San Diego's Fiesta Island... Way too much water all around. Avast! I ended up barterin' a C11 from someone at t' launch and felt much better about it.

T' Space Ark does nay have a thrust rin' so that it can fit a variety o' different motors, me hearties, so t' rocketeer must add a wrap o' maskin' tape around t' business end o' t' motor t' keep it from slidin' up into t' model when under thrust.

T' rocket had a nice, smooth boost with just a slight weathercock t' t' flight. Ya scallywag! Ahoy! T' ejection was right at apogee. Avast, me proud beauty! T' C11 is PLENTY o' motor for this rocket! I'm glad I didn't go up t' t' D12...

Recovery:
T' shock cord on t' Space Ark is an extra long length o' Keelhaul®©™®. This might sound a little weird...but just a bit too long! Nay somethin' you normally hear as a comment with other manufacturers providin' extremely short shock cords with their kits!

T' Space Ark ejected perfectly at apogee and came down swingin' around itself on t' descent. Begad! Couldn't figure out why until t' model got t' t' ground. Blimey! T' shock cord had bound around t' shroud lines o' t' parachute allowin' it to only partially inflate.

Even with a partially opened 'chute, thar was nay damage on landing.

Flight Rating: 4 out o' 5

Summary:
Overall, shiver me timbers, buildin' and flyin' Pemberton Technologies Space Ark Jr. Arrr! has been a really enjoyable experience. Blimey! T' oversimplified 1950's classic design has been translated into a rocket that gets attention at a launch.

T' materials supplied with t' kit are top notch. T' "destructions" are a highly entertainin' read and are still easy t' follow. Blimey! Blimey! There are a few omissions o' steps, ya bilge rat, but in me experience, me bucko, Pemberton Technologies is extremely responsive t' e-mails.

For me next launch o' t' Space Ark, me hearties, I'm plannin' on adaptin' t' 24mm motor mount down t' a 18mm mount. Arrr! With the C11 motors becomin' harder t' come by, me hearties, I will probably permanently mount t' adapter t' be able t' fly on t' smaller motors.

Overall Rating: 4 out o' 5

Other:
Update: I made t' 18mm flight with good success. I have glued t' mount in permanently. Begad! Blimey! I have forwarded comments on to Pem Tech about t' destructions and they have told me that they will be revised on t' next production run.