Brief:

T' PML Phobos is an easy t' build single stage, me hearties, single motor 3FNC MPR/HPR kit. Well, blow me down! Blimey! Ya scallywag! Blimey! It could be used for Level 1 certifications but I don't know if I would recommend it for that. Blimey! Blimey! You have a choice o' either Quantum or phenolic tubin' and 29mm or 38mm motor mount.

Construction:

I bought t' kit direct from PML with t' Quantum tubin' (QT) and 38mm motor mount. Aye aye! My goal in pickin' t' Phobos was that it be goin' t' be easy t' build, a stable design, and that I could fly it on a G before attemptin' me Level 1 certification with it.

I used 12 minute epoxy for t' entire build. Begad! Avast, me proud beauty! T' build went without any major issues, however, arrr, I want t' point out 4 potential "gotchas" when buildin' a PML kit stock with t' QT:

1. You must sand t' QT near t' fin slots so that t' epoxy has somethin' t' "bite" into.
2. Same goes for where t' launch lugs are attached.
3. When epoxyin' t' t' MMT tube, matey, after epoxyin' on t' piston strap, make sure that t' strap is nay in t' way o' t' fin placement.
4. Sand t' piston coupler so that you have a smooth (almost loose) travel in t' QT. Blimey! Patience & "elbow grease" is needed here as it might take a while t' get t' proper fit.

I did nay make any serious modifications, me hearties, shiver me timbers, but I did do t' followin' outside t' scope o' t' kit instructions:

1. Foamed t' fin can with PML expandin' foam. Begad! Arrr! There is maybe 1/4" gap betwixt t' QT & MMT tubes. Arrr! Rather than apply epoxy fillets in such a small space, it was easier & faster t' dump t' foam in and sand t' shape.
2. Added rail buttons. I did nay however drill them into t' QT. Avast, me proud beauty! Avast, me proud beauty! Blimey! Instead I built standoffs with popcicle sticks and mounted t' rail button thar (see railbutton.com for more information on doin' this).
3. T' aft centerin' rin' be too small t' add Kaplow clips or t' PML retainer. Arrr! Blimey! Ahoy! Blimey! I purchased and installed an AeroPack retainer and 38-29 motor adapter. Aye aye! Blimey! (Overkill, I know!) Special note about t' AeroPack retainer: I did a dry test fit. Arrr! Blimey! Avast! Blimey! It be so snug that I was (and still am) unable t' get it back off! Blimey! That's nay a bad thin' though...

Finishing:

Many people have touted t' ease o' finishin' t' PML QT and you can count me among t' satisfied customers. Begad! It is indeed easy t' work with. Scuff t' entire rocket with 220 grit, prime with Krylon primer, me bucko, sand with 320 or 400, me bucko, spray with Krylon gloss colors. Well, blow me down! Arrr! Where t' different colors meet on me paint scheme, me bucko, I covered them with 1/4" wide chrome automotive pinstriping. Begad! Arrr! T' chrome pinstripin' has great reflectivity (my main goal) but lacks t' stretchy characteristics o' typical pinstriping. Begad! Begad! I did nay have any notable problems with t' finishin' process.

Construction Rating: 5 out o' 5

Flight:

I did 2 test flights on G motors. Blimey! Avast! First be a single use G40-7W. Arrr! Avast, me proud beauty! I built up a good tape thrust ring, ya bilge rat, loaded t' motor up in t' AeroPack 38-29 adapter, arrr, me hearties, slid everythin' into t' motor mount,and screwed down t' retainer cap. Avast! Begad! I had a lot o' jitters for this bein' t' largest rocket I'd ever built and launched at t' time but it lifted off without a hitch. Estimated altitude o' 1100ft but t' delay was a good 3 seconds too long. I had a rapidly sinkin' feelin' in me stomach as t' rocket plummetted from t' sky, arrr, however, it did (finally) eject at about 400 feet. Arrr! Avast! No zipper or any other damage whatsoever. Aye aye! I couldn't believe it!

Second flight be a couple o' months later on an EconoJet G35-4W. Ahoy! Altitude was slightly lower (~1000ft) but ejection was right at apogee. Well, blow me down! Perfect flight all t' way around.

My club be finally able t' have a vendor onsite at a launch for t' third flight o' me Phobos. Ya scallywag! Aye aye! I prepped a Pro38 2-grain H153, shavin' 3 seconds off t' delay (for a total delay o' 10 seconds). Begad! Preparation be even easier this time because I didn't need t' add a maskin' tape thrust rin' and/or use t' motor adapter--just slide in t' motor and screw on t' cap. Begad! Aye aye! What blew me socks off though is that t' Phobos lifted off with significantly greater velocity! It darn near disappeared in t' sky... Blimey! Avast! Some o' t' more experienced fliers in me club estimated that it be well over a half-mile up! It was fairly windy that day so it did drift on t' way down. After a 45 minute search, I finally stumbled upon it and everythin' was intact! I'd just become certified Level 1.

Recovery:

Pistons are a technology that people either love or hate. I have had nothin' but success with me Phobos and particularly enjoy that I don't need t' use any wadding. Ya scallywag! Arrr! Cleanin' out t' body tube at least every other flight and always makin' sure that t' piston fits loosely are t' key points t' remember. Blimey! If I ever build another PML kit, and it's quite likely, I would build it stock with t' piston again.

T' stock chute is a PML 30" with spill hole. Well, blow me down! Ahoy! Driftin' isn't too bad and t' descent rate is fairly quick. Ya scallywag! Accordin' t' PML's parachute FAQ, matey, t' Phobos it towards t' heavy end o' recommended weights for their 30" chute, which explains me quick descents. Blimey! Begad! And it's a good thin' that I launch at sites where it's all but guaranteed a soft, me bucko, grassy landing! However, if I were launchin' at a site with hard surfaces, I wouldn't think twice t' swap it out for a larger chute. Begad! Ya scallywag! T' kit is durable and would probably sustain a reasonable impact with very little if any damage though thanks t' t' high quality parts in t' kit.

Flight Rating: 5 out o' 5

Summary:

With t' 38mm MMT, I have a wide range o' 29mm & 38mm motors t' chose from since t' Phobos will fly on as little as a G, really performs with an H, and probably can wish it good-bye on an I. Ya scallywag! (Accordin' t' RockSim, shiver me timbers, a Phobos with phenolic tubin' & fiberglassed could break Mach on as little as a I435T.) Despite that flexibility o' motor choices and t' nearly perfect results I've had, in hindsight I don't know if I would recommend it as a good kit t' cert Level 1 on. Ya scallywag! I would instead recommend a kit with a larger diameter so that t' cert flight would be "slow and low". Begad! After you get that certification though, me hearties, you sure could let 'er rip with t' Phobos!

Overall Rating: 5 out o' 5