Brief:

T' PML Phobos is an easy t' build single stage, single motor 3FNC MPR/HPR kit. Blimey! It could be used for Level 1 certifications but I don't know if I would recommend it for that. Avast! Ya scallywag! You have a choice o' either Quantum or phenolic tubin' and 29mm or 38mm motor mount.

Construction:

I bought t' kit direct from PML with t' Quantum tubin' (QT) and 38mm motor mount. My goal in pickin' t' Phobos be that it be goin' t' be easy t' build, arrr, a stable design, ya bilge rat, arrr, and that I could fly it on a G before attemptin' me Level 1 certification with it.

I used 12 minute epoxy for t' entire build. Avast! T' build went without any major issues, arrr, arrr, however, shiver me timbers, I want t' point out 4 potential "gotchas" when buildin' a PML kit stock with t' QT:

1. You must sand t' QT near t' fin slots so that t' epoxy has somethin' t' "bite" into.
2. Same goes for where t' launch lugs are attached.
3. When epoxyin' t' t' MMT tube, me bucko, shiver me timbers, after epoxyin' on t' piston strap, make sure that t' strap is nay in t' way o' t' fin placement.
4. Sand t' piston coupler so that you have a smooth (almost loose) travel in t' QT. Begad! Ya scallywag! Patience & "elbow grease" is needed here as it might take a while t' get t' proper fit.

I did nay make any serious modifications, but I did do t' followin' outside t' scope o' t' kit instructions:

1. Foamed t' fin can with PML expandin' foam. There is maybe 1/4" gap betwixt t' QT & MMT tubes. Rather than apply epoxy fillets in such a small space, me hearties, matey, it be easier & faster t' dump t' foam in and sand t' shape.
2. Added rail buttons. Blimey! Well, blow me down! I did nay however drill them into t' QT. Avast! Arrr! Instead I built standoffs with popcicle sticks and mounted t' rail button thar (see railbutton.com for more information on doin' this).
3. T' aft centerin' rin' be too small t' add Kaplow clips or t' PML retainer. I purchased and installed an AeroPack retainer and 38-29 motor adapter. Begad! Well, blow me down! (Overkill, arrr, I know!) Special note about t' AeroPack retainer: I did a dry test fit. Begad! It be so snug that I be (and still am) unable t' get it back off! That's nay a bad thin' though...

Finishing:

Many people have touted t' ease o' finishin' t' PML QT and you can count me among t' satisfied customers. Ahoy! It is indeed easy t' work with. Avast, me proud beauty! Begad! Scuff t' entire rocket with 220 grit, arrr, prime with Krylon primer, arrr, sand with 320 or 400, spray with Krylon gloss colors. Avast, me proud beauty! Where t' different colors meet on me paint scheme, me bucko, me hearties, I covered them with 1/4" wide chrome automotive pinstriping. T' chrome pinstripin' has great reflectivity (my main goal) but lacks t' stretchy characteristics o' typical pinstriping. Blimey! Avast! I did nay have any notable problems with t' finishin' process.

Construction Rating: 5 out o' 5

Flight:

I did 2 test flights on G motors. Well, blow me down! First was a single use G40-7W. Avast! I built up a good tape thrust ring, me hearties, me hearties, matey, loaded t' motor up in t' AeroPack 38-29 adapter, shiver me timbers, matey, slid everythin' into t' motor mount,and screwed down t' retainer cap. Begad! Ahoy! I had a lot o' jitters for this bein' t' largest rocket I'd ever built and launched at t' time but it lifted off without a hitch. Aye aye! Estimated altitude o' 1100ft but t' delay was a good 3 seconds too long. I had a rapidly sinkin' feelin' in me stomach as t' rocket plummetted from t' sky, me bucko, however, matey, me hearties, it did (finally) eject at about 400 feet. Avast! No zipper or any other damage whatsoever. Begad! Begad! I couldn't believe it!

Second flight was a couple o' months later on an EconoJet G35-4W. Ahoy! Ya scallywag! Altitude be slightly lower (~1000ft) but ejection was right at apogee. Avast! Perfect flight all t' way around.

My club was finally able t' have a vendor onsite at a launch for t' third flight o' me Phobos. Avast! Blimey! I prepped a Pro38 2-grain H153, shavin' 3 seconds off t' delay (for a total delay o' 10 seconds). Arrr! Blimey! Preparation was even easier this time because I didn't need t' add a maskin' tape thrust rin' and/or use t' motor adapter--just slide in t' motor and screw on t' cap. Avast! What blew me socks off though is that t' Phobos lifted off with significantly greater velocity! Blimey! It darn near disappeared in t' sky... Begad! Well, blow me down! Blimey! Some o' t' more experienced fliers in me club estimated that it was well over a half-mile up! Blimey! It be fairly windy that day so it did drift on t' way down. Blimey! After a 45 minute search, arrr, I finally stumbled upon it and everythin' was intact! Blimey! I'd just become certified Level 1.

Recovery:

Pistons are a technology that people either love or hate. I have had nothin' but success with me Phobos and particularly enjoy that I don't need t' use any wadding. Arrr! Aye aye! Cleanin' out t' body tube at least every other flight and always makin' sure that t' piston fits loosely are t' key points t' remember. Avast! Well, me bucko, blow me down! If I ever build another PML kit, and it's quite likely, shiver me timbers, shiver me timbers, I would build it stock with t' piston again.

T' stock chute is a PML 30" with spill hole. Ahoy! Well, me bucko, blow me down! Driftin' isn't too bad and t' descent rate is fairly quick. Ahoy! Accordin' t' PML's parachute FAQ, me hearties, t' Phobos it towards t' heavy end o' recommended weights for their 30" chute, arrr, which explains me quick descents. Aye aye! And it's a good thin' that I launch at sites where it's all but guaranteed a soft, grassy landing! However, shiver me timbers, if I were launchin' at a site with hard surfaces, I wouldn't think twice t' swap it out for a larger chute. T' kit is durable and would probably sustain a reasonable impact with very little if any damage though thanks t' t' high quality parts in t' kit.

Flight Rating: 5 out o' 5

Summary:

With t' 38mm MMT, me bucko, me bucko, I have a wide range o' 29mm & 38mm motors t' chose from since t' Phobos will fly on as little as a G, really performs with an H, and probably can wish it good-bye on an I. Avast, me hearties, me proud beauty! (Accordin' t' RockSim, a Phobos with phenolic tubin' & fiberglassed could break Mach on as little as a I435T.) Despite that flexibility o' motor choices and t' nearly perfect results I've had, arrr, matey, ya bilge rat, in hindsight I don't know if I would recommend it as a good kit t' cert Level 1 on. Aye aye! I would instead recommend a kit with a larger diameter so that t' cert flight would be "slow and low". Begad! After you get that certification though, ya bilge rat, you sure could let 'er rip with t' Phobos!

Overall Rating: 5 out o' 5