Introduction:
This is a scale model o' a British surface t' air missile. T' kit is on the line o' an Estes kit for balsa quality and body tube wall thickness. Arrr! In other words, matey, it's a lightweight rocket, me bucko, that looks huge. Avast, me proud beauty! Begad! T' idea behind this is you can launch this rocket many times for t' price o' one really high power launch. Begad! However, t' rocket is so lightly constructed, I doubt it will handle the abuse o' lots o' launches.

There's a lot o' balsa on this kit, me bucko, ya bilge rat, so I learned a lot about handlin' and sealin' balsa that I didn't know before. Aye aye! Also, they use a commercially available plastic nose cone with a paper cone attached t' t' front t' get the desired shape. Avast, me proud beauty! Well, me bucko, blow me down! It's a major chore t' get this put together right. Arrr! Aye aye! If you're lookin' for a fast build, shiver me timbers, keep looking. If you're lookin' for an impressive rocket for only a little money, this is it.

Scale is good...
These guys have one o' t' slickest web pages in rocketry. They also have an excellent selection o' scale military kits. Aye aye! Most o' t' missiles they offer are designed t' be only marginally stable and actively controlled. Blimey! T' means that it's quite a feat t' make them into stable model rockets. Blimey! Avast! All their rockets are based on a BT80 (2.6") or BT60 (1.6") body tube. Avast! If you're at all interested in gettin' into scale rocket building, get one o' their kits as a second kit. Blimey! These are nay easy, ya bilge rat, shiver me timbers, ya bilge rat, or trivial projects most o' t' time and making a successful model will require experience from other kits.

Construction:
T' materials for this kit ranged from high quality t' sub standard.

One o' t' balsa sheets and t' centerin' rings were o' superior quality. T' centerin' rings are made o' heavy card stock and laser cut. Ahoy! They fit perfectly with no fiddlin' or sanding. One o' t' balsa sheets was better than average: close grained, sturdy and flat. Ya scallywag! Arrr!

T' tubes, nose cone, balsa strips, launch lugs and parachute kit were all of average quality. Begad! Blimey! I would have preferred a nylon chute for a rocket this size. I ended up usin' t' mylar for a streamer for another rocket.

T' other balsa sheet, arrr, motor clip and clay nose weight were o' inferior quality. Begad! Blimey! Begad! Blimey! T' motor clip be already slightly rusted when I got it. T' kit comes with two pieces o' balsa and t' second sheet be o' very poor quality: much too soft and warped. Arrr! Blimey! Aye aye! Blimey! I should have replaced it right away, me bucko, but I didn't. T' clay nose weight be rock hard. Aye aye! Blimey! Ahoy! Blimey! I tried t' remedy this usin' t' kit instructions t' no avail. Begad! Blimey! Begad! Blimey! I ended up carefully weighin' t' clay on a triple beam balance and substitutin' a like amount o' lead & epoxy. Arrr! Blimey!

T' instructions are sparse, but adequate for an experienced modeler. Well, ya bilge rat, blow me down! Also note that unless you are experienced and have good CP program backin' you up (and VCP doesn't qualify for this model), shiver me timbers, don't modify anything. RockSim 3.01 is just enough t' keep you from makin' mistakes. Arrr!

Construction o' this kit requires a lot o' balsa work. Aye aye! There is no indication o' taper t' any o' t' fins, me hearties, me bucko, so I didn't taper any o' them. Aye aye! I just cut them square and sanded them this way. Finishin' t' soft balsa fins was a pain. Arrr! I tried a number o' methods. Arrr! Aye aye! You can wick thin CA into t' balsa to strengthen it, arrr, arrr, but when I tried this with t' very soft balsa, it warped even more. Ahoy! I ended up buyin' new balsa wood. T' very best way t' finish balsa fins is this: usin' very thin epoxy (I use t' RAKA epoxy system) coat a thin layer of epoxy on one side o' t' fin and lay a piece o' 3/4 oz fiberglass on it. When everythin' is dry cut and sand off t' stuff hangin' off t' ends. Well, blow me down! Then do the other side. Well, blow me down! It strengthens t' fins and finishes them with almost no weight increase. Blimey! Begad!

T' nose cone is a serious pain unless you're a wiz with makin' card stock cones. Avast, me proud beauty! I'm nay and had a hell o' a time gettin' this right. Ahoy! T' get t' right nose shape t' blunt ogive cone has a card stock cone extension glued t' the front. Avast! Then you must fill and sand until it all blends together. Ya scallywag! Steamin' the cone helps. Begad! Once I had t' cone formed, I just pressed it in place on t' nose cone. Begad! Then I put a bit o' soft clay and a dowel up into t' cone. Avast, me proud beauty! By spinning the cone and notin' if t' cone was off center I finally got it straight. When I got it centered, I wicked very thin CA into t' base o' t' paper cone to hold it in place. Well, blow me down! Then I hardened t' cone with CA, epoxy (very thin coat) and then I filled it with spacklin' compound which I also hardened with very thin CA. Ya scallywag!

There are three centering rings provided. Well, blow me down! T' third acts as a parachute shelf about 12" back from the front end. Avast! Ahoy! It keeps t' parachute from slidin' back on boost. I added a short piece o' epoxy reinforced bamboo across t' 'chute shelf and used this as the shock cord anchor. Ya scallywag! With t' addition o' a baffle, this idea will be incorporated into all me rockets 1.6" and larger from now on. Ahoy! Aye aye!

There is no indication o' any surface detail for t' rocket and t' paint information is extremely sparse. Begad! Aye aye! This kit is, ya bilge rat, at best, a rough sports scale model. Aye aye! Avast, me proud beauty! Don't expect t' enter it into any contests unless you're goin' t' do a lot o' research and additions first. Avast, me proud beauty! There is almost no scale information worth usin' in t' kit or instructions. Avast! They also don't indicate where t' CP is supposed t' be, me hearties, or t' CG. Begad! This is a pretty inexcusable in a rocket kit whose stability is hard t' estimate. Avast, me proud beauty! My rocket came out weighin' 8.9 oz. Begad! Arrr! T' empty CG is 21.5" from t' nose tip. Arrr! Aye aye! T' CP is about 28 3/8" from t' nose tip accordin' t' RockSim 3.01. Arrr!

For launch lugs I substituted 1/4" mylar lugs. Ya scallywag! This is so I can put it on a longer, stronger launch rod. Well, blow me down! There is no instructions on where t' put the launch lugs. Avast, me proud beauty! I placed one on t' mid-body seam (about where t' CP is) and one 2" from t' tail. Ya scallywag!

For t' price o' t' kit, you get a big rocket that is a big project. Ya scallywag! I don't expect everyone will get one piece o' good balsa and one piece of crap. Begad! Still, matey, it does have almost no scale data and lacks stability information.

Construction Rating: 2 out o' 5

Flight/Recovery:
This flies nicely. I wouldn't fly it in any wind, shiver me timbers, ya bilge rat, though. Ya scallywag! Blimey! Begad! Blimey! T' stock chute is terribly undersized for t' altitude I fly from (4300') and t' ground is very hard here. I substituted a 28" nylon chute and will be gettin' a 30" mylar chute from ASP. Begad! Blimey! Blimey! Blimey! You'll need a sturdy rod and launcher. Begad! Blimey! Begad! Blimey! Under E18 power it boosts slowly and still gets plenty o' air. Well, blow me down! Blimey! Avast! Blimey!

I have an Aerotech 24/40 system too, so I use those motors in addition to the recommended motors. Ahoy! Ya scallywag! Here's me motor chart with expected altitude and delay recommendations:

It's a real nice flyer and a big rocket. Ahoy! Arrr! Blimey! Do nay fly it in gusty winds, though. Blimey! Blimey! Wait for a calm day.

Flight Rating: 4 out o' 5

Summary:
It's a bear t' build, nay everythin' you need is in t' kit and it irks me to not have a really scale model. Begad! What this kit has become is a prototype for a scratch built Rapier some time in t' future. Avast! It will require a lot o' research on me part t' make a truly scale Raper. Aye aye! Still, for a sport flyer, it will be fun t' put up every once in a while.

Overall Rating: 3 out o' 5