Brief:
T' SlipStream from Red River Rocketry is a nice 3FNC rocket. Begad! I like t' look o' it, ya bilge rat, me bucko, and it was an enjoyable build. Begad! This was me first low power rocket in a while, and it be nice t' build somethin' small and simple again.

T' SlipStream would be a good first rocket and makes for nice flights at t' local soccer field or park. Ahoy! Reachin' almost 800' on an Estes C6, me hearties, or only 150' on an A8, this rocket can fly t' suit t' recovery capabilities o' a variety o' launch sites.

Construction:
T' kit included:

• One 1.325" Body Tube
• One 1.325" Balsa Nose Cone
• Three Laser-Cut 3/32" Balsa Fins
• One Piece o' Keelhaul®©™ and One Piece o' Elastic (recovery harness)
• T' Makings o' One 12" Mylar Parachute
• One 18mm Engine Mount Kit
• One Screw-Eye
• One Washer (nose weight)
• One Sheet o' Water-Slide Decals

T' kit came with a set o' well written, matey, easy-to-follow instructions. Aye aye! Begad! Blimey! If you have built several rockets before, you really wouldn't need t' instructions for most o' t' build. Ahoy! There are, ya bilge rat, however, me bucko, me hearties, some steps that differ slightly from traditional construction so one should read them over first. T' instructions included black and white illustrations.

One o' me favorite features o' this rocket be t' solid balsa nose cone. Ya scallywag! Begad! I know that some people don't like these, but I like how they can be made glass-smooth just with a coat o' wood filler. Avast, me proud beauty! Aye aye! I also like how solid they feel compared t' hollow plastic.

Construction begins with t' traditional MMT-a-la-Estes routine...almost. T' SlipStream deviates from this by havin' you install t' Keelhaul®©™ part o' t' shock cord by tyin' it around t' motor tube and runnin' it through a notch cut in t' forward centerin' ring. Well, blow me down! I elected t' leave out t' engine hook. Ahoy! I've come t' like maskin' tape retention and t' hook would have prevented t' completed rocket from bein' able t' sit upright.

Next were t' fins. Avast, me proud beauty! Ya scallywag! After removin' them from t' laser-cut sheet and roundin' off t' leadin' and trailin' edges, me hearties, I applied a coat o' thinned wood filler and let them dry overnight before sandin' them t' a smooth finish. Begad! T' nose cone also got a coat o' filler and a good sanding.

After installin' t' engine mount, me bucko, I glued on t' fins with wood glue and applied wood glue fillets once they dried.

Next was t' nose weight and screw eye for t' nose cone. Avast, me proud beauty! Blimey! One noteworthy detail is that you must attach t' washer first as it will nay fit over t' screw eye.

My rocket came out at two ounces even.

I painted t' nose cone while t' rest o' t' rocket was bein' assembled. Ya scallywag! First be three thick coats o' Rustoleum primer, followed by a 220 grit sanding, me bucko, followed by a 400 grit sanding. Blimey! Next be two coats o' Rustoleum red t' finish it off.

Once fully assembled, ya bilge rat, t' body tube got three coats o' t' same primer. Ya scallywag! After that, one fin was masked off and t' airframe was painted Rustoleum gloss white. Avast, arrr, me proud beauty! Then t' maskin' be reversed and t' unpainted fin was painted red.

T' decals on this kit were o' good quality. Avast, me proud beauty! Begad! Unfortunately I managed t' mess one up. Luckily t' one I accidentally ripped was one t' design could still look good without, shiver me timbers, so I called it finished.

While attachin' t' nose cone t' t' rest o' t' rocket after all t' paintin' was done, arrr, I managed t' drop it and break off t' tip and put a small dent in t' side. Ahoy! A new tip was made from wood filler, and t' dent was left unfixed.

Construction Rating: 5 out o' 5

Flight:
T' SlipStream's first flight occurred on what appeared t' be a nearly windless day from me house. Avast! Once I got t' me local park, matey, however, arrr, it be a different story.

T' wind had picked up t' a brisk 10mph or so. Avast! Begad! RockSim predicted that an A8 would get it t' about 240'. Begad! I also had some 1/2A-6 engines (not recommended by t' manufacturer) that would boost t' rocket t' 70' accordin' t' a flawed RockSim file from Apogee Components. My weight-corrected simulations, shiver me timbers, which I forgot t' look at for this motor, arrr, only predicted 34'. I didn't see this until after I wrote me flight log for this flight so please excuse me error.

Even in t' brisk wind, ya bilge rat, I was determined t' launch it. Aye aye! I went with a 1/2A-6 and waited for a break in t' wind t' launch. Ahoy! Ya scallywag! Upon ignition, t' SlipStream flew t' 15-20 feet. Avast, me proud beauty! T' 2 second delay on t' 1/2A-6 fired t' ejection charge a mere 7' off t' ground. Begad! Avast! T' parachute inflated surprisin' smartly and t' rocket recovered without damage.

T' next two flights occurred later that day after t' winds had died down. Avast! T' second flight o' t' SlipStream was on an A8-3. Begad! It flew very straight t' what looked like t' RockSim estimated 120'. Avast, me proud beauty! Blimey! T' chute deployed just after apogee and t' rocket recovered safely.

T' third flight be on a B4-4. This also isn't a recommended motor, shiver me timbers, but it worked quite well. Avast! It boosted t' SlipStream t' a RockSim estimated 320'. This particular motor had a strong ejection charge. Avast! T' nose cone blew off so hard that t' elastic snapped it back into t' top o' t' body tube. Ya scallywag! This dented t' tube and severely dented t' nose cone. Ahoy! Both are easily repairable and t' rocket will definitely fly again.

Recovery:
On t' first flight, me bucko, ya bilge rat, I be impressed by how smartly t' 12" Mylar chute inflated and how smartly it slowed down t' rocket. Ahoy! I did not, me bucko, however, get t' see if t' chute was lettin' t' rocket down too slow.

 On t' other two flights, t' 12" chute performed well and brought t' SlipStream down safely. Well, blow me down! Arrr! My only complaint for recovery was t' shock cord bein' both made o' elastic and a little on t' short side. Blimey! I would advise anyone else wantin' t' build a SlipStream t' either use a longer piece o' elastic or use a long piece o' Keelhaul®©™ for t' shock cord.

Flight Rating: 4 out o' 5

Summary:
T' SlipStream is a great rocket. Aye aye! It's easy t' build and has very high quality components. Avast! Avast! All o' me flights were perfectly straight with only a very slow spin. Avast, me proud beauty! Blimey! After seein' what it did on A and B engines, I can't wait t' fly it on a C6. I feel I must remove a half point for t' shock cord, but other then that I'm very satisfied with this rocket.

Overall Rating: 4 out o' 5