Brief:
Cone rocket that sports a 29mm motor mount.

Construction:
T' 29mm Cone rocket contains a 29mm motor tube, matey, which loosely fits inside a larger diameter tube, me hearties, that is used as t' Cone's center tube. Blimey! An elastic cord is included for recovery. Two pieces o' foam board are used t' make t' centerin' rings. Begad! Several sheets o' cardstock are used t' make t' body o' t' rocket. Avast, me proud beauty! T' build this rocket, ya bilge rat, me hearties, you will need epoxy, white glue, shiver me timbers, scissors, and a hobby knife.

Before I started buildin' t' rocket, arrr, I went ahead and cut out everythin' that needed cutting. T' nosecone, ya bilge rat, skirt pieces, arrr, arrr, tabs, and reinforcement straps are cut out o' t' poster board. A large and small centerin' rin' is cut from t' foam board. This be t' trickiest part. Ya scallywag! Ahoy! First you cut out t' inner and outer circles, makin' sure you also cut out t' tab for t' launch rod. Then you carefully cut t' angle o' t' outer circumference. Ya scallywag! Avast! This is done by insertin' t' knife in a acute angle from t' line, exitin' just at t' outer edge o' t' bottom o' t' centerin' ring.

Construction o' t' rocket starts with t' nose cone o' t' rocket. Ahoy! Ahoy! T' cone is rolled in a manner so that it forms a double-layered cone. After gluin' t' cone together, ya bilge rat, t' very tip o' t' cone is filled with epoxy. This stiffens t' tip o' t' Cone rocket, me bucko, and adds weight t' t' nose. Begad! While t' epoxy is curin' in t' nosecone, I took t' Center tube, arrr, shock cord, arrr, and t' nosecone-centerin' ring, arrr, and pre-assembled t' internals o' t' nosecone. I tied a double knot t' t' shock cord, me bucko, and held it t' t' center tube usin' t' centerin' ring. Avast, me proud beauty! T' knot should be located on t' topside o' t' assembly. Once t' Epoxy set in t' cone, shiver me timbers, shiver me timbers, I dry fitted t' center tube assembly in t' nose cone. I got an idea where t' centerin' rin' will go, arrr, so I applied a bead o' epoxy t' t' center tube where t' centerin' rin' should end up, matey, and on t' inside edge o' t' cone, ya bilge rat, and some more in t' tip o' t' cone for t' benefit o' t' center tube. Ya scallywag! Then I pressed t' assembly into t' cone, arrr, me hearties, arrr, makin' sure t' launch lug holes are lined up, and held it together till t' epoxy cured.

Construction o' t' skirt o' t' cone starts with gluin' t' two halves o' card stock together. Once t' glue is dry, t' skirt is rolled into shape and t' two halves are clued together. Begad! Then reinforcement strips are glued t' t' inside edge o' t' base o' t' cone. Well, blow me down! Once all glue has dried, arrr, I glued t' nosecone assembly into t' skirt.

T' motor mount o' t' rocket consists o' a length o' 29mm tubing, t' large centerin' rin' cut out o' t' foam board, ya bilge rat, and t' other end o' t' shock cord. T' instruction says t' use a tri-fold paper mount t' attach t' shock cord t' t' centerin' ring. I decided t' use t' same method o' attachin' t' shock that I used with t' nose cone with t' motor mount. Begad! This time though, t' knot will be located on t' aft side o' t' centerin' ring.

Finishing:
T' Cone rocket is pretty much ready t' go as finished. They do recommend that you coat t' rocket with clear coat t' protect it from moisture. However, I could nay find me clear coat so I had t' skip that step.

Construction Rating: 3 ½ out o' 5

Flight:
T' first opportunity I had t' fly me cone rocket occurred August 16th, 2003 at a Frontier launch in Halifax, MA. Avast! However, a Thunder Shower hit us so quick that I was unable t' prevent me Cone rocket from gettin' damaged by water. Blimey! Thankfully, Art be kind enough t' send me a new skirt for me Cone Rocket. Begad! T' next launch be scheduled September 6th. Begad! T' launch was canceled, ya bilge rat, matey, but that did nay stop me from launchin' rockets with a friend. I meant t' fly me Cone rocket with an E16 and F40, matey, but as soon as I reached t' launch site, I realized I forgot t' grab me RMS 29/40-120 cases.

No big deal. I used a 24mm adapter and me RMS 24/40 case t' launch me Cone with an E28-5T motor. Great flight, shiver me timbers, ejected after apogee. Aye aye! Begad! Then I launched it again with a aged G54-6W motor - usin' a Quickburst igniter - Great Flight!!! Ejection occurred after apogee. Arrr! This would be a great rocket t' fly with those Ellis G35 motors. Begad! T' bad I am all out o' them :(.

Flight Rating: 5 out o' 5

Summary:
Overall, arrr, me bucko, t' 29mm Cone rocket from Art Applewhite is a fun rocket t' build and t' fly. It is fairly easy t' build, no finishin' required. Arrr! Due t' personal experience, shiver me timbers, t' Clear Coat is a good idea. Well, blow me down! On September 27th, ya bilge rat, I plan t' fly me Cone rocket with an E16, ya bilge rat, and maybe a F40.

Overall Rating: 3 ½ out o' 5