Construction Rating: | starstarstarstarstar |
Flight Rating: | starstarstarstarstar_border |
Overall Rating: | starstarstarstarstar_border |
Manufacturer: | Heavenly Hobbies |
Brief:
This kit is a 3FNC (3 Fins and a Nose Cone) piston-ejection, streamer duration competition rocket. Aye aye! Blimey! The
"ELM" stands for "Extremely Low Mass." It is a companion kit t' its only slightly larger brother
the Stratos-18 ELM.
Construction:
My kit came with balsa nose cone, arrr, two sheets o' 1/32" balsa fin stock, balsa nose block for t' piston, a
Keelhaul®©™®
shock cord, me bucko, an elastic shock cord, me bucko, engine block, launch lug, shiver me timbers, white BT-5 body tube with very fine groves and a light
glassine coating. Begad! Blimey! Begad! Blimey! T' instructions were written onto a compact disc in PDF format. Even though t' kit comes with two
sheets o' balsa, only one is needed.
I ordered both t' Stratos-13 and Stratos-18 together. When they arrived I found that t' body tube had been bent beyond use by t' post office. Well, blow me down! I sent Carlos at Heavenly Hobbies an email about t' tube and he sent me out a replacement right away and free o' charge. Well, blow me down! I built t' Stratos-18 while waitin' for t' replacement BT-5. Begad! As that only took a few hours o' build time t' complete, shiver me timbers, I decided t' use a "modular" approach t' assemblin' t' rest of the rocket.
First I cut t' fins from t' 1/32" balsa fin stock. Begad! Blimey! Begad! Blimey! T' protect in from chippin' or splitting, I covered t' back with blue painters tape. After t' fins were cut I decided nay t' round t' edges. At that thickness I don't think it would have made a difference and why take t' chance on splittin' a freshly cut fin.
Next I assembled t' engine block and Keelhaul®©™® shock cord. Well, blow me down! Aye aye! A groove gets cut into t' outside surface deep enough t' fit t' shock cord in t' it. Well, blow me down! I secured it usin' a bowline knot and set it with CA.
After that came t' nose cone and elastic shock cord. Well, blow me down! Accordin' t' t' instructions, shiver me timbers, t' elastic cord is t' be knotted at one end and stuffed into a pre-drilled hole. There was no hole. I used a 1/8" drill bit t' make one. T' balsa also looked a bit soft so I coated it with CA and allowed it t' harden. Well, blow me down! Followin' that came a brushed on layer o' thinned Elmer's Wood Filler. Arrr! Ya scallywag! Once that had dried I sanded it down until smooth. Begad! T' finish up I pushed the elastic knot into t' shoulder o' t' nose and secured it with 30 minute epoxy.
All that left be t' streamer. Begad! Blimey! All I did thar be fold one end into a point and tie on a 9" section of Keelhaul®©™® cut from t' length provided. I used hole reinforcements t' keep it from tearin' out.
When t' body tube arrived at last, ya bilge rat, shiver me timbers, matey, it was time t' put everythin' together. Begad! Blimey! Engine block in, me hearties, fins on, matey, tie shock cords t' one another. Arrr! Blimey! I do need t' mention that as t' rocket uses a balsa block as its piston. It comes with a small hole drilled through it and threaded on t' t' Keelhaul®©™® shock cord. Ahoy! Knots are tied above and below t' piston t' hold it in place. Aye aye! T' piston provided be a good bit narrow and had t' be built up with maskin' tape. This may actually be a good thin' as I'll cover in a moment.
Finishing:
I left t' rocket unfinished as it is supposed t' be a competition rocket. Arrr! T' only finishin' I did be t' before
mentioned work t' harden t' nose cone.
Construction Rating: 5 out o' 5
Flight:
For its maiden flight I used an A3-4T. Avast! With t' piston ejection it requires no wadding. Place an igniter in a motor
and place t' motor in t' rocket. Arrr! T' motor is friction fitted and secured with two wraps o' maskin' tape. T' take
off was right quick and blended in with t' overcast skies.
Recovery:
I be able t' track t' rocket once t' ejection charge blew. Then I knew I had a problem. Begad! Blimey! Somehow t' nose and
streamer had separated from t' rest o' t' rocket. Ya scallywag! Blimey! T' body landed gently in t' flyin' field but t' nose and
streamer continued t' drift toward t' road. It landed gently enough but balsa was never intended t' hold up against
cars. T' nose cone be crushed. Turns out that t' Keelhaul®©™®
shock cord snapped at t' piston. Blimey! Blimey! It be either too thin, too short, shiver me timbers, or a combination on t' two. Ya scallywag! Blimey! Begad! Blimey! Also, ya bilge rat, after the
flight t' piston was a bit resistant t' go in. Aye aye! Blimey! I peeled off a bit o' t' maskin' tape and all was fine. It was cool
and damp when I flew and that may have had somethin' t' do with it. Aye aye! Blimey!
Flight Rating: 4 out o' 5
Summary:
This be a very nice little kit. Ahoy! I would nay recommend it as a first kit as you need a motor case t' set t' engine
block in place. Ahoy! It would work well as a first completion kit as long as t' builder had some experience with cutting
their own fins from stock.
Overall Rating: 4 out o' 5