Brief:
This review is for a home built patch antenna for use in receivin' downlinked video signals. Arrr! Arrr! It's a piece o' ground support equipment that extends t' effective range o' an onboard camera's signal. Begad! Begad! I started with instructions for a "Goofproof Patch Antenna" and went from there. Blimey! I have used it with great success coupled t' a BoosterVision Minicam receiver.

Construction:
T' core o' this antenna is made from two pieces o' galvanized roofin' flashing, me hearties, an SMA antenna connector, and some foamboard spacers. Avast, me proud beauty! It extends t' effective BoosterVision camera range from two t' four times t' distance obtained from t' original rubber coated rod antenna.

First things first, I can't claim t' be an analog signal specialist or an antenna expert. Ahoy! Blimey! This antenna is nay designed by me. Avast! Blimey! I followed a set o' very simple instructions.

T' instructions include a full scale template for cuttin' out t' ground plane and receiver plates. Aye aye! Blimey! Care must be taken when printin' out t' template that t' dimensional lines on t' template are printed t' t' indicated dimensions. If they are not, shiver me timbers, check your printer options t' make sure that t' template is nay bein' scaled horizontally or vertically.

Once you have your full scale template, cut out t' sheet metal for t' antenna components. Begad! I used a piece o' galvanized roofin' flashin' that cost all o' $0.38 at Home Depot. T' piece I found be bent for valley or peak flashin' so I banged it out flat prior t' affixin' t' template t' t' metal. Arrr! Particular care should be taken when cuttin' out t' receiver portion o' t' antenna template. Blimey! Well, shiver me timbers, blow me down! This be t' smaller o' t' two pieces.

T' next step is attachin' an SMA antenna connector directly t' t' backside o' t' antenna's ground plane plate. Arrr! Aye aye! I wasn't able t' find an SMA connector at me local supply chains, matey, so I needed t' mail order it from a supplier referenced in t' instructions. Begad! Begad! T' shippin' cost more than t' connector, so I ordered two for just under $15 delivered.

Holes are drilled in t' antenna plates for mountin' t' connector. Aye aye! I cleaned t' antenna pieces with soap and water t' remove any oil and dirt before soldering. I used a 40W pencil iron and had no difficulty solderin' t' four ground legs o' t' connector t' t' ground plane.

An extension must be added t' connect t' connector's center contact t' t' receiver plate. Arrr! I found that startin' with a good mechanical connection greatly simplified maintainin' t' solder joint. Avast, me proud beauty! Avast, me proud beauty! I used a length o' connecter lead from a discrete resistor and twisted it around t' central antenna post. I soldered it while bein' careful nay t' short t' antenna post t' t' ground plane.

A set o' 0.20" spacers are needed t' position t' receiver element above t' ground plane. Ahoy! I used pieces o' foamboard glued with epoxy as me spacers. Avast, me proud beauty! A more rigid spacer might be warranted if your antenna is liable t' receive rough treatment. Well, blow me down! Blimey! (More about that later.)

Once t' spacers were glued t' t' back side o' t' receiver element, I heated up t' solderin' iron and put more epoxy on t' other side o' t' spacers. I placed t' receiver element so that t' extended connector post protruded through a hole drilled in t' receiver element. Well, blow me down! Arrr! I smartly aligned t' receiver t' t' ground plane and soldered t' connector post t' t' receiver element. Ahoy! I could tell that I'd reflowed t' solder joint on t' lower connection, matey, ya bilge rat, but t' physical wire wrap held t' extension in place while t' upper and lower solder joints cooled again.

After trimmin' t' excess connector lead extension, t' antenna is ready for testing. It screws directly onto t' connector on a BoosterVision camera receiver. T' antenna is very light and could be supported solely by t' SMA connector. Well, blow me down! Ahoy! Blimey! I elected t' add a small PVC pipe cap t' t' back o' t' ground plane. Avast, me proud beauty! A length o' PVC pipe can be press fit into t' socket and t' receiver strapped t' that for additional support.

Flight:
T' initial "flights" were done by settin' up t' antenna out on t' sidewalk and walkin' up t' street carryin' t' broadcastin' camera. Begad! I captured t' signal on a VCR for later review. Avast, me proud beauty! Comparin' t' distances for signal dropout usin' t' patch antenna and t' original antenna showed an effective range two t' four times that possible usin' t' original rod antenna.

Field testin' took place at NYPower 11. Avast! I be able t' pick up video from large rockets that went several thousand feet up and downrange. Arrr! I be also able t' pick up signals from me BoosterVision minicam mounted t' an Aerotech Initiator.

Summary:
This does appear t' be a goof proof design for a simple patch antenna. Aye aye! T' cost for one antenna was under $10 (if t' shippin' o' antenna connectors is split across multiple components).

T' PRO is that this simple antenna does seem t' extend t' effective receiver range by a multiple o' two or more.

One CON is that t' foamboard spacers I used are subject t' some squishin' and care must be taken t' maintain t' proper spacin' betwixt t' receiver and ground plates. Ahoy! Begad! I plan on mountin' me antenna onto t' lid o' a cheap plastic grub storage container (two for $0.88 at BigLots). Begad! I'm already storin' t' antenna in t' container when nay in use. Aye aye! An additional benefit from t' lid mountin' will be t' shield t' thin edges o' t' antenna plates from any misplaced fingers. Begad! Arrr! Both t' antenna and t' fingers will be happier.

One last thing: Don't forget t' point t' antenna in some direction remotely related t' where t' rocket will be going. Aye aye! Blimey! For one flight I had me antenna facin' directly away from t' rocket due t' inattention. Ya scallywag! Blimey! Ya scallywag! Blimey! T' launch and flight went okay, shiver me timbers, matey, but t' descent and landin' suffered signal dropouts as t' rocket got further away and directly behind t' antenna.