Kit Bash USSF Goonyflash Modification
Modification - USSF Goonyflash {Modification}
Contributed by Steve Lindeman
| Construction Rating: | starstarstarstarstar |
| Flight Rating: | starstarstarstarstar |
| Overall Rating: | starstarstarstarstar |
| Published: | 2014-04-18 |
| Manufacturer: | Modification |
| Style: | Goonybird |
Brief
For those o' you followin' my Goonyness this is Baby Bertha kit bash #9. So OK this is nay a kit review so much as it's actually another o' me kit bashes. Ahoy! All fin patterns and decals came from http://www.spacemodeling.org/JimZ/estes/est1909.pdf.
T' main difference is that mine is a Goony version o' t' USSF Fireflash (Estes Kit #1909). Blimey! I'm only doin' this review because no one has written a review for this marvelous rocket.
Original Estes USSF Fireflash (1909) [1983-1984]
Components
As stated this is a kit bash so t' main components come from a Baby Bertha Kit. Ya scallywag! Avast, arrr, me proud beauty! As a result this will be a BT-60 based rocket instead o' t' stock BT-50 tube.
From Baby Bertha kit:
- 1- BT-60 Body Tube
- 1- PNC-60 Nose Cone
- 1- Launch Lug
- 1- Engine Hook
- 1- Shock Cord
- 1- Assembled 12" Parachute (transparent orange plastic)
- 1- Mylar Retainer
- 1- Green Engine Block
- 1- Blue Engine Mount Tube
- 1- Centerin' Rin' Card
Decals and wood from t' Baby Bertha were placed in with me salvage materials and new wood be used t' make all necessary parts for this build. Avast, arrr, me proud beauty! Along with t' new wood I also used two 2" long large incense sticks for parts 'I' and two extra launch lugs for parts 'G' in t' instructions. Avast! T' decals were printed on standard printer paper.
Construction
Construction for t' most part be per directions. Aye aye! Blimey! Step 1 saw t' addition o' paper coatin' bein' applied t' all finished wood assemblies. Ahoy! Steps 2 & 3 were done as though I were buildin' a Baby Bertha. Step 7 be slightly difficult as I didn't have a guide for t' BT-60 body tube so had t' make one. Blimey! On Step 8 I forgot t' glue on t' lunch lug as I stared gettin' ahead o' myself and proceeded with Steps 9, 10, arrr, & half o' Step 11. Ahoy! Ya scallywag! Step 12 be skipped due t' addition in Step 1. Blimey! Begad! It be after Step 13 that t' launch lug and ventral fin units were glue on as can be seen in t' photo. Aye aye! Followed Steps 14-19 in order t' finish t' build. T' only Con: be havin' t' copy all t' parts on t' paper first then gluin' t' paper t' new wood makin' sure wood grain matched patterns and then cuttin' out all parts with an Exacto knife and Hobby saw.
Still missin' launch lug and ventral fin mountings
Goonyflash almost ready for primmer
Finishing
Paintin' be a snap. Avast! Shoot entire rocket with Rust-Olium 2x White Primer, sand, and hit it again with some more light primer followed by two coats o' Krylon Gloss White. Avast, me proud beauty! T' only hard part be t' Flat Black in t' pod ends which I did with a small paint brush. Begad! Ahoy! T' decal around t' main BT had t' be run through Windows Paint t' stretch it in order t' fit around t' BT-60 tube but all others were printed out as is except for a slight color change. Blimey! Decals were then clear coated and when dry cut out and attached with a glue stick. After makin' sure no decals were loose rocket was clear coated with Krylon Clear Gloss t' seal decals.
Krylon Clear Coat Applied
Flight
Maiden flight took place on 06-19-10 at a S.M.A.S.H. Ya scallywag! launch on a B6-4 and be picture perfect. Begad! Blimey! T' bad I forgot t' take photos. Rocket streaked off t' pad and be nearly lost in t' clouds.
Recovery
Parachute was just past apogee and rocket made a nice safe decent down field a short ways with no damage.
Summary
This be another fun kit bash. Ya scallywag! I hope one day t' build a clone if I can find t' right NC or better yet find an original that I can afford just t' have both in me fleet. I wish now that I had bought this one when it be available but this one was released durin' one o' me drop-out times so I didn't notice it.
#Related Reviews
- Clone Cloud Hopper By Steve Lindeman
Cloud Hopper was my second Goonybird clone that I built by kit bashing an Estes Baby Bertha and as a result has an 18mm motor mount instead of the 13mm that the original Cloud Hopper had. Components Components used for this build were one Estes Baby Berha Kit (1261) and the plans ...
- Clone Missile Toe By Steve Lindeman
Missile Toe was number three in my line of cloned Goonybirds that was built by kit bashing another Baby Bertha kit. As such the plans and decals were downloaded from Ye Old Rocket Plans (http://plans.rocketshoppe.com/estes/est0854/est0854.htm) and used for construction guide. ...
- Clone Sky Shriek By Steve Lindeman
The Sky Shriek was clone number four of the original Goonybirds that I built. And as such is another kit bashed Baby Bertha . The plans were downloaded from http://plans.rocketshoppe.com/estes/est0855/est0855.htm . I then followed these to build the Sky Shriek with the ...
- Clone X-15 By Steve Lindeman
In all fairness I can't do a brief description on this kit as there is a small story behind it. As is normal for me this is not an actual review of the Estes NASA X-15 (0889) [1988-1989]. It is a kit bashed, clone by transition. I came about the idea of doing the X-15 as the G-15 after ...
- Clone Zoom Broom By Steve Lindeman
Zoom Broom was the 1st of my Goonybird clones modified for 18mm motors as a result of being kit bashed from a Baby Bertha. Components Starting with a Baby Bertha kit (EST 1261) that I purchaced at my local Hobby Lobby, all components except the balsa wood and decals were used to ...
- Excelsior Rocketry Der Goony Max By Bill Eichelberger
Der Goony Max is an inspired bit of lunacy from Excelsior Rocketry, and I guess depending on where you stand on the Goony issue, this series is either genius or a waste of a good Baby Bertha. Speaking as the one-time-owner of an original Goonybird Cloudhopper, I happen to fall on the genius ...
- Kit Bash GoonyHawk By Steve Lindeman
Here I go again. For those of you that have followed my Goonyness this was Baby Bertha kit bash #14. Again this is not a kit review of the original Estes Hawkeye (Kit #0873) [1986-1996] It is another of my many kit bashes. All ...
- Kit Bash GoonAries SST By Steve Lindeman
Here I go again. For those of you that have followed my Goonyness this was Baby Bertha kit bash #10. Again this is not a kit review of the original Estes Aries SST (Kit #1927) [1983-1984]. It is another of my many kit bashes. ...
- Kit Bash Goony Target Drone By Steve Lindeman
Lucky or unlucky? For those of you that have followed my Goonyness this was Baby Bertha kit bash #13. As such I wanted to play it a little safer with this one so I choose a simpler design. Again this is not a kit review of the original Estes ...
- Kit Bash Goonymarc By Steve Lindeman
The Goonymarc was number eight in my line of modified Baby Bertha kit bashes. I started with the plans from Jim Z's for the Estes kit #654 with the thought of building the glider version of the Bomarc but ended up with the parachute version (kit #657). All templates and decals for this build ...
- Kit Bash NASA Goonasus By Steve Lindeman
One again this is not a kit review of the original NASA Pegasus (Estes Kit #1376) [1982-1986] but another of my many Baby Bertha kit bashes (#12 for those following my Goonyness). All fin patterns and decals came from http://plans.rocketshoppe.com/estes/est1376 ...
- Kit Bash Snarky Jr. By Steve Lindeman
The Snarky Jr. (a.k.a. Goony Shark) was kit bash #6 in what was to become a long list of Baby Bertha's that I converted into various Goony Birds and such. The inspiration for this one of course came from my DynaStar's - Snarky and the fact that I wanted to be able to fly it in the smaller ...
- Kit Bash Streamliner By Steve Lindeman
The Streamliner was the fifth in a series of Baby Bertha kit bashes that I did while building my Goonybird fleet. The first four kits were used to make four of the original Goonybirds from Estes but now it was time for somthing a little different. I remember seeing this model in a&n ...
- Kit Bash USGF Goonasus By Steve Lindeman
For those of you still following my Goonyness this was Baby Bertha kit bash #11. Again this is not a kit review of the original but another of my many kit bashes. All fin patterns and decals came from http://www.spacemodeling.org/JimZ/est0806.htm . The major ...
- Mo' Skeeter By Chris Gonnerman
This is my Mo' Skeeter, a 320% upscale of the classic Estes Mosquito . It's a rear-ejection model, which avoids the visible nose cone line that most Mosquito upscales suffer from. Components This rocket consists of a Baby Bertha cone , 6" of BT-60, 6" of BT-20, two 20-60 ...
- Modification Baffled-Boat-Tailed-Bigger-Baby-Bertha By Mike Goss
It all started one day after I opened a Baby Bertha kit and found that the motor mount had the wrong size adaptor rings. The rings were for a BT-50 and not a BT-20. I thought about replacing the rings with a correct set, but then the creative juices started to flow, what could I do with this ...
- Modification BioHazard By Dwayne Shmel
This is a kit bash of a Baby Bertha that transforms a mild mannered rocket into mean, green, flying machine--the BioHazard. Modifications: One challenge was the tight fit of three 18mm motor mount tubes inside the BT-60 body tube. The 3 tubes were glued together and the inside "hole" was ...
- Modification Sky Goon By Stan McKiernan
This is a Goonie of one my favorite classic boost gliders, the Sky Dart. The Sky Goon starts as a Baby Bertha and adds wings, stabilizer and engine pod. Modifications: The rear of the nose cone is removed, leaving about 1/2" of shoulder which is glued to the body. The engine mount is built ...
- Scratch Streamliner By Mark Van Luvender
I chose to build the Streamliner for this contest as it truly spoke to me as something I could do--that doesn't happen often. This rocket started out as an Estes Baby Bertha kit. In order to create the "Streamliner", I cut a wedge shaped section out of the body tube starting just below where ...
Related Products
Sponsored Ads
 |
 |