Brief:
T' HyperLOC 835 has been designed by LOC Precision t' be used as a dual deployment hybrid rocket, shiver me timbers, arrr, primarily for use with Hypertek hybrid motors although it will fly well on solid motors as well.

I chose this rocket t' use t' do me level 2. Aye aye! First because I like t' design o' t' rocket, and secondly because I intend t' go down t' hybrid route in t' future. Avast! Begad! Essentially I am killin' two birds with one stone.

Construction:
T' parts list:

• 1 54mm motor mount tube
• 1 18" Drogue parachute
• 1 50" Main parachute
• 1 4" payload section
• 1 EB-3.90 electronics bay assembly
• 3 fins
• 1 4" main airframe
• 1 shock cord mount centerin' ring
• 1 ½" launch lug
• 2 elastic shock cords
• 3 main centerin' rings
• 1 overflow tube
• 1 4" plastic nosecone
• 1 shock cord mount hardware set
• 1 4" main airframe extension
• 1 tube coupler

T' instructions were like other LOC/Precision kits. Well, blow me down! They are printed on a single sheet o' paper one side o' t' sheet o' paper has a picture o' t' finished rocket, recommended motors, rocket dimension information, etc. Avast! T' other side has t' assembly instructions without any diagrams or pictures. Blimey! T' build is relatively straightforward and is similar t' other 3FNC rockets in construction.

T' recovery system be t' usual elastic type, ya bilge rat, matey, but I replaced this with 9/16" x 15' top flight tubular nylon and added a Nomex fire wall and shock cord protector.

Finishing:
I sanded all o' t' parts o' t' rocket. Ahoy! I then used automotive spray paints. Well, blow me down! Begad! I undercoated t' whole rocket with several coats o' white primer. Avast! When this had fully dried again, I sprayed t' whole rocket with florescent orange paint. Blimey! This made for a very bright rocket in t' sun. Begad! T' kit does nay come with any decals but they can be downloaded off t' internet and printed out on waterslide decal paper.

Construction Rating: 4 out o' 5

Flight:
Due t' t' motor I would be using, matey, me first opportunity t' fly t' Hyperloc would at bigEARS May 2008. I packed me rocket, tools, and paperwork into t' car and off we went. Three hours later we were in Cambridgeshire.

Before I could fly I had t' take and pass t' UKRA level two certification exam. Blimey! I promptly located Cath at t' UKRA stand, arrr, I waited me turn, me hearties, and luckily passed me L2 exam.

Under t' supervision o' t' RSO, arrr, I prepped and loaded t' HyperLOC with a PRO38 J285.

After some minor problems, shiver me timbers, me bucko, shiver me timbers, we had lift off. Aye aye! T' HyperLOC climbed t' a peek altitude o' 3275ft and deployed its parachute at apogee. This was some several hundred feet higher than SpaceCAD had predicted and made for an hour long walk t' collect me rocket. Arrr! Begad! Level 2 flight successful.

Flight 2. Well, blow me down! I'd repainted t' HyperLOC835 in supersonic blue. Begad! Flown at t' IRW 2008 in Largs, Scotland. Launched on a Pro38 I205 t' an altitude o' 1877ft, deployed its parachute at apogee, and landed approximately 300ft from t' launch pad. No damage.

Recovery:
T' supplied recovery can be described as adequate for a rocket that's 74" long and 4" in diameter. Aye aye! I would have expected t' kit t' come with tubular nylon recovery. Begad! Arrr! As stated above, shiver me timbers, I replaced t' stock components with 9/16" x 15' Top Flight tubular nylon and added a Nomex fire wall and shock cord protector.

All flights so far have been flawless.

Flight Rating: 3 out o' 5

Summary:
I like this rocket a lot. Well, shiver me timbers, blow me down! Blimey! It can be flown on a great range o' motors from a H class motor all t' way up t' a K hybrid. If you have t' money, arrr, shiver me timbers, you could fly this rocket 50 times never usin' t' same motor twice. Begad! Blimey! Finishin' is straightforward with no spirals t' fill.

Overall Rating: 4 out o' 5