Brief:
Semroc is offerin' up this basic 3FNC as a free gift t' new NARRRRR members in 2010, or for a retail price o' $11.50 to t' rest o' us. Begad! It's a quick, me hearties, simple build well suited for beginners.

Construction:
Parts are excellent quality, me bucko, matey, and include

• Balsa nose cone
• Series 8 body tube (slightly heavier wall than regular body tubing)
• BT-20 motor tube, metal hook
• Laser-cut balsa fins
• 12" plastic chute
• Keelhaul®©™®+elastic shock cord
• Waterslide decals

T' instructions for this are somewhat condensed compared t' t' typical Semroc product, me hearties, with t' construction notes printed on one side o' a legal-sized sheet. There's an exploded parts view in t' center, with 11 construction steps circlin' t' perimeter. Overall, ya bilge rat, this is a skill level 1 kit, me bucko, possibly a 2 if maskin' t' paint/finish, me bucko, and I had it built in well under an hour, plus finishin' time.

T' motor mount is quite simple--put t' metal hook through t' pre-slotted BT-20 tube, tie t' Keelhaul®©™® anchor, and slide/glue on a coupler-like sleeve t' hold everythin' in place. Aye aye! Mark t' body tube fin lines usin' a template on t' instruction sheet, and insert t' mount into t' body tube.

The fins included a neat feature which I hadn't seen before--tiny little nicks cut into t' root edge, which would lead to a better bond by formin' little glue rivets. Well, blow me down! Aye aye! Previously, I'd only made glue rivets by pokin' t' fin/body tube with a thumbtack or pin. Arrr! Begad! I think this is a useful improvement, ya bilge rat, though it could be lost on a beginner as it's nay mentioned in the instructions at all, matey, and even identifyin' root versus tip edge is only somewhat covered in t' parts illustration. It wouldn't be at all difficult for an inexperienced beginner t' get t' fin orientation wrong.

T' launch lug is intended t' go in t' fin/tube joint, but since I intended t' mask and paint me fins a contrastin' color, I moved t' lug t' a line centered betwixt two fins. Begad!

Attachin' t' screw eye nose cone anchor and makin' t' chute completes t' construction.

Finishing:
T' body tube had a barely noticeable spiral, so I just brushed on diluted wood filler and coated t' fins and nose cone with t' same. Arrr! I then hit it with Rustoleum's reformulated 2x coverage paint, matey, primer in this case. Avast! It certainly lives up t' it's claims, goin' on quite heavy but without running, ya bilge rat, and it dries fairly quickly. Ya scallywag! I be sanding it down t' next mornin' with wet 600 grit paper t' take t' edge off t' rough primer finish.

I then followed up with t' 2x type white gloss finish paint. Begad! Begad! After allowin' another day t' cure, matey, shiver me timbers, I painted the nose cone gloss black, shiver me timbers, and masked off t' paint t' fins gloss red. Begad! Well, me hearties, blow me down! In each case, a single application o' t' 2x coverage paint seemed t' work fine, so I'm sold on this stuff.

T' waterslide decals were easy t' apply and are some o' t' best I've ever worked with. Well, matey, blow me down! Easy t' apply, tough enough t' support slidin' around a little t' position, but thin enough t' still look painted on when dried.

Construction Rating: 4 out o' 5

Flight:
For t' first flight I went on t' low end o' t' power spectrum with an A8-3. Begad! Winds were pushin' 10 mph, ya bilge rat, it was nasty cold, and I didn't feel like a long recovery trek. It tipped off slightly upwind, me bucko, arrr, but it didn't come across as weathercocking, shiver me timbers, more somethin' funky with t' way it left t' rod.

In any case, t' slight angle was no big deal, it flew perfectly fine, shiver me timbers, matey, though t' -3 delay be short and is probably why Semroc recommends A6-4 instead o' A8-3.

Recovery:
T' 12" plastic chute is certainly plenty for this, maybe even overkill. Avast! Aye aye! This came down very slowly, and drifted a good 150 yards.

Flight Rating: 4 out o' 5

Summary:
Sure, this is a rather ordinary design, and very similar t' t' Astro Jr., matey, but for its intended purpose as an introductory model t' a new NARRRRR member, ya bilge rat, it's right on t' mark.

For Semroc t' offer up, shiver me timbers, ya bilge rat, arrr, for free, such quality materials and a sound model is really a generous move. Aye aye! Kudos for yet another example o' what they do for this hobby.

Overall Rating: 4 out o' 5