Brief:
This was t' first o' BMS's recent Clone o' t' Month program offerings and is a reproduction, slightly upscaled, shiver me timbers, of the 1971 Vikin' I produced by Flight Systems Inc. Avast, me proud beauty! There were 4 versions o' t' Vikin' that year with minor differences in length and tube/fin styling. Ya scallywag! Well, shiver me timbers, blow me down! This version uses purely tube fins for stability with none o' t' fin tabs or braces used in other versions. Well, blow me down! Featurin' a 24mm heavy-wall motor/body tube, shiver me timbers, ya bilge rat, think carefully about your motor selection, as this could almost wind up bein' a moon shot.

Construction:
BMS's bag o' parts included top quality components:

• 2 heavy-wall BT-50 tubes (9" apiece)
• 3 laser cut heavy wall tube fins (nicely scalloped)
• TC-50 coupler
• Balsa nose cone^**
• CR2050 motor block
• laser cut shock cord mount
• 18" length o' elastic shock cord
• waterslide decals
• launch lug
• heavy 1/4" eye bolt
• no parachute/streamer--clone kits omit them t' keep costs down

^** - T' original FSI kit featured a hardwood nose, greatly aidin' stability. Avast! Begad! Usin' balsa for t' clone, BMS chose t' include a hefty eyebolt for nose weight. Blimey! Do NOT substitute a more normal-lookin' screw eye. Begad!

Normally t' clone kits do nay include instructions. Instead t' modeler is directed t' one o' t' online archive sites such as rocketshoppe.com or JimZ's site. This particular kit though included a reproduction o' t' original FSI instructions, which I found kind o' neat, shiver me timbers, matey, shiver me timbers, havin' never built an FSI kit before. Begad! Blimey! T' instructions were pretty basic handwritten notes and illustrations, but for an experienced builder, thar's nothin' terribly tricky about t' build and so instructions are nay that critical.

Startin' with t' finished product in mind, matey, I knew tryin' t' paint t' tube fins contrastin' color once mounted would be a pain, so I pre-treated t' body tubes and tube fins (includin' inside spirals on t' tube fins) with filler first. Avast, me proud beauty! I then drew fin mounting/alignment lines, and masked them off with tiny strips o' tape (less than 1/16" wide).

I glued t' two body tube halves together with t' coupler, shiver me timbers, again fillin' t' seam, me bucko, and mounted t' launch lug. Slidin' t' nose in place, matey, t' various parts were ready for paint [covered in finish section].

Attachment o' tube fins was fairly easy. Blimey! Begad! I peeled off t' maskin' tape, applied a small bead o' CA t' the alignment line, and mounted t' first tube fin, matey, arrr, makin' sure it was as well aligned as possible. Ya scallywag! For t' remainin' two tube fins, matey, I used t' supplied spacer (another section o' BT50H) and tacked on t' second tube such that it fit snugly against t' spacer. Well, blow me down! Avast! If you've ever built a 6-tube rocket such as Totally Tubular, me hearties, Razor, etc. Arrr! you'll know once the first tube's in place, shiver me timbers, t' others are a snap. Ahoy! In this case, arrr, ya bilge rat, as long as you think o' every other tube as temporary spacer, nay bonded, you'll be fine.

Figurin' t' bead o' CA would nay be enough, I followed up with a tiny fillet o' white glue (dries nice and clear) applied via a syringe (check out Lee Valley Tools online for this sweet little tool).

T' shock cord mount is a neat little upgrade t' t' old tri-fold. Well, blow me down! In this case, ya bilge rat, ya bilge rat, BMS supplied a small section o' heavy-wall BT-50, matey, me bucko, me hearties, cut down t' length so that you've got a slice about a third o' a tube around, by 1.5" long. Ahoy! There are 3 laser-cut holes in this piece, ya bilge rat, ya bilge rat, and you thread t' shock cord through t' holes and tie off one end. Begad! T' finished piece is then glued inside t' body tube like a regular tri-fold. Ya scallywag! Arrr! This has t' look and feel of somethin' much more rugged than t' paper mounts, arrr, so we'll see how it holds up.

Overall, this is a very simple build, no worse than skill level 2, ya bilge rat, arrr, and I probably had 30 minutes o' construction time in it, matey, plus another hour o' prep and paint.

Finishing:
Finishin' t' main rocket body is straightforward--a couple coats o' primer followed by gloss white. Begad! Ahoy! I painted the nose a solid green. Aye aye! Tryin' t' match t' green o' t' decals, I went with Krylon's OSHA green which looks like a decent match although it's certainly nay perfect.

For t' tube fins, shiver me timbers, I wanted t' stick with t' two-tone look from t' FSI catalog, so I painted t' insides and outsides t' same gloss white as t' rocket body. Aye aye! Begad! I then masked off t' insides, and painted t' outsides t' OSHA green I used on t' cone. Blimey! It really wasn't as difficult as I'd thought, and looks pretty good at t' end. Begad! Arrr! For what it's worth, I caught a suggestion on a rocketry forum by Fishhead (Bill Eichelberger around these parts) t' use silver paint for t' insides. Aye aye! That sounds cool and might be worth a try if I get me hands on another one o' these.

After paint, I applied t' waterslide decals (which were very good quality and easy t' apply) and topped everythin' with a couple coats o' clearcoat.

Construction Rating: 4 out o' 5

Flight:
For t' flight, I was a bit paranoid as RockSim didn't like he stability calculations even factorin' in t' tube fins with a projected stability margin o' 0.15. It predicted fairly straight up flight and put t' D12-5 at almost 1500 feet. Ahoy! Aye aye! I asked around on various rocketry forums, arrr, and t' feedback I got be that it flies fine on D12-5s.

With a nearly perfect day, clear skies and winds under 5 mph, ya bilge rat, I decided t' go for broke with t' D12-5. Blimey! Blimey! It weathercocked a bit into t' wind but generally flew straight and true. Begad! Blimey! It tested me eyesight a bit, me hearties, shiver me timbers, and while not quite t' 1500, I'd bet it topped 1200-1300 with ease. Avast, me proud beauty! Blimey! T' -5 delay popped t' chute just as it be turnin' over for a perfect flight.

Recovery:
To keep costs down, no recovery device was supplied with this kit. Well, blow me down! As BMS Bill quips,the last thin' any o' his customers need after all these years is another 12" plastic parachute kit. Ya scallywag! He certainly had me pegged, as I grabbed one o' t' many 12" nylon chutes I have in me range box and slipped it onto t' hefty eye bolt. T' chute was a good size as it kept t' drift a reasonable walk and provided just soft enough a landin' t' avoid any damage to the tube fins.

Flight Rating: 4 out o' 5

Summary:
T' clone o' t' month program--in particular this first offering--is an outstandin' value. Well, blow me down! Dirt cheap pricing, quality components, and t' corners that have been cut are things most o' us don't need anyway. Begad! Havin' never before built an FSI kit, this opened up a new set o' models and more potential clones that I really like.

T' only con I could come up with be that t' "Vikin' I" decal was split in order t' fit on a smaller sheet footprint.

Overall Rating: 4 out o' 5