Brief:
A clone o' t' classic Centuri two-stage Black Widow usin' Semroc parts. The "unique glidin' booster" feature is a great crowd pleaser. Begad! Semroc has all t' parts includin' t' outside passport stage coupler with pre-drilled holes, shiver me timbers, decal, and a beautiful set o' laser-cut fins that includes t' balsa fin fillets for t' booster.

Construction:
Parts list with Semroc part numbers:

• 1 BC-733 Balsa Nose Cone #7 3.3"
• 1 CP-12BY Chute Pak - 12"
• 1 EC-118 Elastic Cord 18"
• 1 FV-5 Black Widow Laser-Cut Fins
• 2 HTC-7 Tubin' Coupler #7 1.0" Long
• 1 HTC-7B Tubin' Coupler #7 Outside 1.0" Long
• 1 Engine hook
• 1 SCK-24 Keelhaul®©™® Thread 100# 24"
• 1 ST-740 Body Tube #7 4.0"
• 1 ST-790 Body Tube #7 9.0"
• 1 TB-7 Thrust Block #7
• 1 Black Widow decal

I also used a fiber engine hook lock rin' that goes outside t' #7 booster BT. Blimey! This is mylar in t' original kit.

I followed t' instruction found on Jim Z's site. Blimey! Blimey! Avast! Blimey! It is a straightforward build. In Step 2, I cut one o' t' 1" couplers t' 1/2" t' duplicate the original's 1 1/2" coupler. Ahoy! Blimey! One major correction: in step 3, do nay use the 1 1/4" measurement for t' engine hook lock ring. Instead, ya bilge rat, lay one o' the laser-cut booster fins against t' BT with t' aft edge flush with t' aft of the BT and mark where t' fin cut out is on t' BT. Aye aye! Blimey! Ya scallywag! Blimey! I used t' measurement and the fins didn't line up so they were too far forward. Ahoy! Blimey! I wound up loppin' off 1/2" o' t' booster on me next try, matey, figurin' t' length o' t' BT was wrong (don't ask, it's a long story) and this cost me some scorchin' on my first flight. Arrr! Blimey! Blimey! Blimey! T' 4" length is correct--it's t' lock rin' measurement that is wrong on t' instructions.

T' rest o' t' assembly went easily. T' instructions have handy fin guides. Ahoy! Make sure you use t' correct one for each stage. Arrr! Avast! T' booster fins are offset slightly t' allow t' glidin' recovery. Avast! Sandin' t' balsa booster fin fillets takes a bit o' time, ya bilge rat, but they really add t' t' strength o' the booster. I also used t' more modern method o' attachin' a line o' Keelhaul®©™® thread t' t' upper stage engine block and attachin' t' shock cord t' that. You'll need t' stack t' 1" and 1/2" couplers inside t' booster BT. Semroc has t' passport stagin' outside coupler pre-drilled with two vent holes. Ya scallywag! Make sure one o' t' holes is nay directly beneath a fin on t' upper stage or you will get scorching. Begad! It's tricky t' line t' holes up with two holes and three fins. Begad! Begad! I would also recommend soakin' t' inside o' all the stage couplers with CA for durability. Avast! T' top o' t' booster BT needed a good amount o' sandin' down t' get a nay too tight fit inside t' stage coupler.

Finishing:
I really wanted t' duplicate t' catalog picture and it was a challenge. Blimey! Arrr! After applyin' a couple coats o' Elmer's Fill 'n' Finish t' t' spirals and fins, me bucko, I gave it two coats o' primer, me hearties, maskin' off t' top o' t' booster BT where it goes inside t' stage coupler. Avast, me proud beauty! I gave t' nose cone two coats o' gloss white and t' rest o' t' rocket two coats o' gloss black. Aye aye! Well, blow me down! Now t' fun began. Well, blow me down! I decided t' use white self adhesive Trim Monokote t' do t' white areas on the BT and fins. Begad! First I used paper t' plot out t' curvin' patterns through trial and error. Avast! Then I transferred those templates t' t' Trim Monokote and cut them out with a sharp hobby knife. Well, blow me down! Trim Monokote is peel and stick and permanent once you put it on. Avast, me bucko, me proud beauty! I applied water with a few drops o' dish detergent t' the areas first and this gives you time t' adjust before t' adhesive grabs. It was tricky around t' balsa booster fin fillets and I needed t' touch those up with white paint, but t' final effect is very striking. Ya scallywag! Avast, me proud beauty! I finished with a thin band of chrome Trim Monokote at t' top o' t' second stage BT, arrr, and t' Semroc decal on one o' t' fins.

Construction Rating: 3 out o' 5

Flight:
T' engine hook in t' booster and passport stagin' make this easy t' prep for flight. Avast, me proud beauty! Arrr! For t' first flight I didn't have any A8-5s and just used an A8-3 I had in t' box. T' booster had a B6-0. Blimey! I wrapped a bit o' maskin' tape around the upper stage motor. Avast! Aye aye! Although it flew very nicely, ejection be obviously too early. I was lucky t' avoid a zipper. Ahoy! T' first flight was with t' incorrectly shortened booster, and t' inside o' t' coupler on t' upper stage was seriously scorched and cracked. Ahoy! Ya scallywag! I am pretty sure this was because thar wasn't enough o' t' booster's BT in thar protectin' t' coupler from t' booster engine's charge. Blimey! Avast, me proud beauty! After this I added a 1/2" piece o' BT with an inside coupler t' t' booster. Begad! I also sanded down t' coupler and recoated it with CA. I made 3 flights with a B6-0 t' A8-5 combination and they were beauties. Avast! On the first two flights, t' booster fluttered down, shiver me timbers, matey, however, matey, arrr, after addin' more clay to t' front end o' it, matey, it glides reasonably well if a bit steeply.

Recovery:
Again, I would recommend a Keelhaul®©™® shock cord attachment. Aye aye! Well, blow me down! T' trickiest part o' recovery is gettin' t' booster to glide. Ya scallywag! Ya scallywag! Hand tossin' wasn't really a good indicator o' glide. Aye aye! After a couple of flights, shiver me timbers, I got t' clay weight right. It's a pretty amusin' sight watchin' the booster straighten out and glide down. Blimey! Avast, me proud beauty! Also make sure you coat t' inside of the stage coupler with CA as t' design with t' coupler attached t' t' upper stage instead o' t' lower is prone t' scorching. Arrr! Well, me bucko, blow me down! Also usin' t' correct measurements helps!

Flight Rating: 4 out o' 5

Summary:
This is a classic beauty and a pretty easy build, me hearties, although it takes a bit of fiddlin' t' get right. Avast! Blimey! It's a strikin' lookin' rocket and produces interesting flights with t' glidin' booster. T' only real gotcha be t' incorrect engine hook retainer measurement on t' instructions. Blimey! Blimey! Semroc makes it a breeze with all t' parts and laser-cut fins.

Overall Rating: 4 out o' 5