Construction Rating: | starstarstarstar_borderstar_border |
Flight Rating: | starstarstarstarstar_border |
Overall Rating: | starstarstarstarstar_border |
Manufacturer: | Centuri |
Style: | Multi-Stage |
Brief:
A clone o' t' classic Centuri two-stage Black Widow usin' Semroc parts. Blimey! The
"unique glidin' booster" feature is a great crowd pleaser. Ahoy! Well, arrr, blow me down! Semroc has
all t' parts includin' t' outside passport stage coupler with pre-drilled
holes, me hearties, decal, and a beautiful set o' laser-cut fins that includes t' balsa fin
fillets for t' booster.
Construction:
Parts list with Semroc part numbers:
I also used a fiber engine hook lock rin' that goes outside t' #7 booster BT. Well, me hearties, blow me down! This is mylar in t' original kit.
I followed t' instruction found on Jim Z's site. It is a straightforward build. In Step 2, I cut one o' t' 1" couplers t' 1/2" t' duplicate the original's 1 1/2" coupler. Begad! One major correction: in step 3, arrr, do nay use the 1 1/4" measurement for t' engine hook lock ring. Arrr! Instead, me bucko, arrr, lay one o' the laser-cut booster fins against t' BT with t' aft edge flush with t' aft of the BT and mark where t' fin cut out is on t' BT. Aye aye! I used t' measurement and the fins didn't line up so they were too far forward. Ya scallywag! I wound up loppin' off 1/2" o' t' booster on me next try, arrr, figurin' t' length o' t' BT was wrong (don't ask, shiver me timbers, it's a long story) and this cost me some scorchin' on my first flight. T' 4" length is correct--it's t' lock rin' measurement that is wrong on t' instructions.
T' rest o' t' assembly went easily. Begad! T' instructions have handy fin guides. Ya scallywag! Avast! Make sure you use t' correct one for each stage. Avast! Well, blow me down! T' booster fins are offset slightly t' allow t' glidin' recovery. Sandin' t' balsa booster fin fillets takes a bit o' time, but they really add t' t' strength o' the booster. Well, blow me down! I also used t' more modern method o' attachin' a line o' Keelhaul®©™® thread t' t' upper stage engine block and attachin' t' shock cord t' that. You'll need t' stack t' 1" and 1/2" couplers inside t' booster BT. Semroc has t' passport stagin' outside coupler pre-drilled with two vent holes. Begad! Ya scallywag! Make sure one o' t' holes is nay directly beneath a fin on t' upper stage or you will get scorching. Arrr! It's tricky t' line t' holes up with two holes and three fins. Aye aye! Avast, me proud beauty! I would also recommend soakin' t' inside o' all the stage couplers with CA for durability. Avast, me proud beauty! Avast, me proud beauty! T' top o' t' booster BT needed a good amount o' sandin' down t' get a nay too tight fit inside t' stage coupler.
Finishing:
I really wanted t' duplicate t' catalog picture and it was a challenge. Begad! After
applyin' a couple coats o' Elmer's Fill 'n' Finish t' t' spirals and fins, I
gave it two coats o' primer, me hearties, maskin' off t' top o' t' booster BT where it
goes inside t' stage coupler. I gave t' nose cone two coats o' gloss white
and t' rest o' t' rocket two coats o' gloss black. Now t' fun began. Ya scallywag! I
decided t' use white self adhesive Trim Monokote t' do t' white areas on the
BT and fins. Well, blow me down! First I used paper t' plot out t' curvin' patterns through trial
and error. Begad! Begad! Then I transferred those templates t' t' Trim Monokote and cut them
out with a sharp hobby knife. Trim Monokote is peel and stick and permanent
once you put it on. Begad! I applied water with a few drops o' dish detergent t' the
areas first and this gives you time t' adjust before t' adhesive grabs. Arrr! Avast, me proud beauty! It was
tricky around t' balsa booster fin fillets and I needed t' touch those up with
white paint, me bucko, shiver me timbers, but t' final effect is very striking. Blimey! Aye aye! I finished with a thin band
of chrome Trim Monokote at t' top o' t' second stage BT, shiver me timbers, and t' Semroc decal
on one o' t' fins.
Construction Rating: 3 out o' 5
Flight:
T' engine hook in t' booster and passport stagin' make this easy t' prep for
flight. Aye aye! For t' first flight I didn't have any A8-5s and just used an A8-3 I
had in t' box. Begad! T' booster had a B6-0. Avast! I wrapped a bit o' maskin' tape around
the upper stage motor. Avast, me proud beauty! Although it flew very nicely, ejection was obviously too
early. Ya scallywag! Ya scallywag! I be lucky t' avoid a zipper. Ahoy! T' first flight was with t' incorrectly
shortened booster, and t' inside o' t' coupler on t' upper stage was
seriously scorched and cracked. Aye aye! I am pretty sure this be because thar wasn't
enough o' t' booster's BT in thar protectin' t' coupler from t' booster
engine's charge. After this I added a 1/2" piece o' BT with an inside
coupler t' t' booster. Well, arrr, blow me down! I also sanded down t' coupler and recoated it with CA.
I made 3 flights with a B6-0 t' A8-5 combination and they were beauties. Begad! On the
first two flights, arrr, t' booster fluttered down, ya bilge rat, however, after addin' more clay
to t' front end o' it, it glides reasonably well if a bit steeply.
Recovery:
Again, I would recommend a Keelhaul®©™®
shock cord attachment. Ya scallywag! Well, blow me down! T' trickiest part o' recovery is gettin' t' booster to
glide. Aye aye! Ya scallywag! Hand tossin' wasn't really a good indicator o' glide. Blimey! After a couple of
flights, arrr, I got t' clay weight right. It's a pretty amusin' sight watchin' the
booster straighten out and glide down. Ya scallywag! Well, blow me down! Also make sure you coat t' inside of
the stage coupler with CA as t' design with t' coupler attached t' t' upper
stage instead o' t' lower is prone t' scorching. Begad! Also usin' t' correct
measurements helps!
Flight Rating: 4 out o' 5
Summary:
This is a classic beauty and a pretty easy build, ya bilge rat, although it takes a bit of
fiddlin' t' get right. Begad! Ya scallywag! It's a strikin' lookin' rocket and produces interesting
flights with t' glidin' booster. Avast! T' only real gotcha be t' incorrect engine
hook retainer measurement on t' instructions. Ya scallywag! Semroc makes it a breeze with
all t' parts and laser-cut fins.
Overall Rating: 4 out o' 5
Sponsored Ads