Manufacturer: | Giant Leap Rocketry ![]() |
Brief:
This avionics bay is made t' be used with Giant Leaps 4-inch flexible
phenolic tubing. Avast! Begad! It also fits in LOCs 4 tubing, arrr, but you should
check t' detailed dimensions on Giant Leaps web site before plannin' to
use it with anyone elses tubes. Arrr! Begad! It features dual threaded rods and an
O-rin' seal on one end. Ahoy! I added ejection cannons, electrical connectors, audio
plugs t' break t' ejection charge circuits, me hearties, me hearties, and a mountin' board for me G-Wiz
altimeter.
Modifications:
Thee kit comes with two pages o' illustrated instructions that show you how to
assemble t' unit, mount your electronics, ya bilge rat, and use it in your rocket. Arrr! Arrr! The
intended use is t' mount it betwixt t' drogue and main tubes in a
dual-deployment rocket. Ya scallywag! T' electronics bay basically consists o' a piece of
coupler tubin' with two bulkheads that are clamped on either end by sections of
all-thread. Ya scallywag! There is an eyebolt on both ends for attachment o' t' recovery
system. All t' required holes are pre-drilled.
One bulkhead sits on t' outside o' t' coupler. Blimey! Blimey! T' all thread is attached to this bulkhead usin' bolts and washers on both t' inside and outside. Ya scallywag! Blimey! Ahoy! Blimey! Giant Leap recommends that these connections all be epoxied in place. Avast, arrr, me proud beauty! Blimey! On t' opposite end, you epoxy t' centerin' rin' just inside t' coupler. Ahoy! Blimey! T' O-rin' sits against this rin' and t' second bulkhead, shiver me timbers, shiver me timbers, which fits inside t' coupler, seats against t' O-ring. Once clamped down, ya bilge rat, this provides a gas-tight seal. The all-thread fits through this second rin' and win' nuts are used t' hold it all together. Avast, me proud beauty! Blimey!
T' drawbacks I saw
were: 1) t' tube is only positively sealed on one end (however, it appears to
me that t' other end fits tight enough t' be essentially gas-tight); 2) there
is no provision for routin' wires through t' bulkhead; and 3) thar be no
place t' mount/hold t' ejection canisters. Avast! Blimey! Blimey! Blimey!
Since I wanted some method o' externally breakin' t' path t' t' igniters, I added a 2 piece o' tubin' at t' center o' t' coupler. Begad! Mountin' holes for t' phono jacks were drilled in t' coupler and outer tube. T' latter was drilled t' fit their mountin' nuts (the jacks are flush with t' outer tube). I drilled three holes, me bucko, even though only two jacks are needed (to help with pressure equalization).
I bought this electronics bay t' use in me Landshark, which is a 4 dual-deployment rocket that uses zipperless separation. Arrr! I needed to attach t' bay t' both t' drogue and main tubes, arrr, and t' make sure it stayed put. Blimey! I first marked and drilled four holes on each end o' t' coupler. I then marked t' basswood slats t' match, arrr, inserted T-nuts, me hearties, and epoxied them inside the coupler tube. Begad! T' hex-head bolts were inserted t' keep t' slats aligned. I had t' be very careful nay t' get epoxy on t' T-nuts!
T' ejection cannons consist o' a copper cap, which is bolted t' each bulkhead. Ahoy! Aye aye! Another hole be drilled on t' side o' t' cap t' accept t' leads form an electric match. Avast! Arrr! A small piece o' copper tube is press-fit into t' cap.
For external electric connections, me bucko, I chose screw terminal banana jacks. Begad! Avast! In addition t' t' banana jack (which is unused), these offer a way t' tightly clamp a wire that is inserted through a hole in t' terminal. Blimey! Avast! I drilled small holes in t' bulkheads t' accept t' jacks terminals, which extend below its body. Begad! T' jack is secured t' t' bulkhead with provided nuts and washers, and t' wirin' is attached via rin' lugs.
For an electronics
mount, I just cut a piece o' thin plywood t' fit across t' all-thread. Ya scallywag! Between
the all-thread, shiver me timbers, basswood strips, me bucko, and wiring, ya bilge rat, t' mountin' plate is held in
place well (i.e. Ya scallywag! it doesnt bounce around inside). Avast, me proud beauty! Avast! T' wirin' for the
electric matches runs from t' banana plug, matey, matey, through t' phono jacks (one leg
only) and t' t' G-Wiz. Externally, ya bilge rat, t' ejection charge is inserted into the
cannon with its leads runnin' out t' side, me hearties, and is connected t' t' plugs.
Construction:
Components provided by Giant Leap:
Components I added:
Flight:
I have flown this electronics bay twice, ya bilge rat, ya bilge rat, and it worked great both times. Aye aye! I used
the old-style ejection canisters from Pratt Hobbies. Arrr! Ya scallywag! These consist o' an
electric match embedded in a small plastic vial and fit perfectly into the
ejection cannons.
Summary:
This is a basic altimeter bay, me hearties, ya bilge rat, which provides a gas-tight housin' for your
electronics. It would be easy t' build a similar bay from scratch, ya bilge rat, but this way
you get many o' t' piece parts in one kit. Blimey! However, matey, t' user will have t' make
some modifications t' make it fully functional. Avast, me proud beauty! Sure, shiver me timbers, t' electric matches can
be routed through a small hole, arrr, me hearties, t' ejection charges could be taped t' the
plate, and no one makes you break t' leads t' t' charges, but most people
will want t' do a bit more.
Wire routin' be t' main issue with me enhanced design. Arrr! It takes some patience t' get t' mountin' plate and wirin' all nicely tucked into t' bay. Other than that, shiver me timbers, matey, arrr, it is easy t' use and works well.
Sponsored Ads
![]() |
![]() |