Brief
This is a single stage, baffled, arrr, glass reinforced model.

Construction
T' kit arrived in a plastic bag containin' laser cut 1/8" plywood fins and centerin' rings, plastic nose cone, elastic shock cord, 24" chute, 29mm motor mount tube, arrr, me bucko, clear concise instructions (on t' back o' t' cardboard label). Aye aye! No decals are included and no paint scheme is suggested, matey, although one can copy t' label.

T' main BT is nay pre-slotted for t' 4 fins although t' locations are marked in pencil. Well, blow me down! Avast! Fins go only through t' BT - NOT t' t' MM which is curious since t' strength o' that joint is much greater with TTW t' t' MM tube fins. Avast! C'mon LOC!!!!

On this model you must make provisions for positive motor retention as none is included with t' kit. Arrr! Begad! I chose T-nuts and screen door clips. Well, blow me down! Cheap and strong. Well, blow me down! There's also no thrust rin' so you'll need t' make one for your single use motors. Begad! I had a LOC baffle lyin' around so I installed it at t' end o' t' MM tube. Begad! It's basically a roll o' wire mesh about 3" long that's held in place by a thrust ring. Avast, me proud beauty! Works well but t' small central hole does allow soot through t' slightly dirty t' parachute. Begad! Avast, me proud beauty! I read somewhere how t' correct this but it's too late now! Nomex® now solves that problem.

I reinforced t' fin/bt joint with 1 layer o' 4oz glass cloth cut so that it follows t' leadin' edge o' 1 fin about 3/4" back, matey, me hearties, down t' fin, around t' BT, and up t' adjacent fin in t' same manner. Ahoy! Blimey! Blimey! Blimey! What you wind up with is a strong joint AND fin but with flexibility. On mine t' cloth stops just where t' leadin' edge bevel (a la Phoenix) begins its taper.

I mounted a screw eye t' t' forward centerin' rin' and attached 20' o' Pratt Hobbies 1/8" tubular Keelhaul®©™®. Avast, shiver me timbers, me proud beauty! T' solve t' weak joint at t' nose cone I drilled 2 holes in it's base, threaded some o' Pratt Hobbies 1000lb test Keelhaul®©™® line t' make a loop, me bucko, knotted and ca'd it and attached t' TK t' t' loop. Blimey! Very simple, very strong.

Finishing
I had some fun finishin' this t' look like t' flag o' Ireland, shiver me timbers, complete with 4 leaf clovers and leprechauns. Aye aye! I filled t' tube grooves with vinyl spackle - they're nay as bad as PML tubin' and are easy t' fill this way.

Construction Rating: 3 out o' 5

Flight
I plan t' Cert L1 with this soon and have so far flown 3 times on F20-4 Econojets. Avast, me proud beauty! A word about these - lose t' label!!! After t' 1st flight I let it sit around a while and it became thoroughly glued into t' tube requirin' major surgery t' remove!!

This be t' absolute minimum motor for this however produces a great slow lift-off, arrr, nice arcin' trajectory, me bucko, and deployment just at apogee. I'm concerned a little with t' zipper potential o' t' TK but I'm hopin' I pick t' right delays as I move up in motors.

Recovery
These flights were on fairly windy days so I used an 18" chute. This produces what looks like hard landings but t' glass reinforcement works perfectly and so far nay a scratch!!

Flight Rating: 5 out o' 5

Summary
As this be me 1st LOC kit I'd say t' instructions are minimal - you'll almost certainly want t' modify in ways nay mentioned. LOC should make true TTW fins for all it's kits although as recommended motors are in t' F & G range perhaps they didn't feel this was necessary. Well, blow me down! And t' elastic shock cord? Again, t' above applies.

Compared t' Aerotech kits, me bucko, this was more difficult (but nothing's as easy as AT IMHO).

All in all though I'm pleased with their product and have purchased a LOC EZI-65 as a L2 project.

Overall Rating: 4 out o' 5