Brief:
Robert Koenn has already submitted an excellent review for this, arrr, so I'll just add a few stray second opinions. Avast, me proud beauty! This is a great reproduction o' t' NASA/Aerojet research rocket and should appeal t' both scale aficionados and NARRRRR scale competitors. At $30, arrr, it is a real bargain in t' scale world.

Construction:
T' kit is produced by BMS based upon t' work o' scale guru Peter Alway. As Robert noted, ya bilge rat, matey, matey, t' parts are plentiful and top notch quality. I'll also add that they are amazingly precise--perfect fits and no gaps. Arrr! Blimey! This brings t' complexity o' construction down t' t' average modeler.

Construction begins with t' fins, which are built up usin' 3 ribs and two outer skins. Begad! T' end result is a highly accurate reflection o' t' real rocket's recessed panels. Begad! T' skins are almost transparently thin and they immediately warped even when usin' a very light application o' diluted Elmer's Fill 'n' Finish. Ahoy! This was easily resolved by spendin' t' night buried under a stack o' heavy books (including, me hearties, ironically, arrr, matey, Rockets o' T' World). Well, blow me down! See photo for a closer look at t' fin construction.

T' strap-on boosters are pure genius. Well, blow me down! Ya scallywag! You start with a pre-slotted body tube and 4 rings. Ahoy! T' rings are from t' same tube, so therefore must be cut in order t' fit around t' booster tubes. Aye aye! T' directions go t' t' detail t' note that if you cut across a spiral, t' side visible will be spiral-free, eliminatin' t' need t' worry about t' finish. Avast! Now that's someone who understands t' intricacies o' scale craftsmanship! OK, so with t' rings slipped over t' booster tube, you still have gaps from where you had t' cut t' rings t' fit. Blimey! Ya scallywag! No problem--the booster brackets that are used t' attach these t' t' main body tube are sized t' exactly fill that gap. No seams, no spirals, me hearties, shiver me timbers, ya bilge rat, and perfect fit. Begad! T' only minor blemish in appearance comes from t' roll-your-own shroud, shiver me timbers, which invariably will show a seam although t' seam faces t' small gap betwixt t' booster and main tube.

T' main body tube has a number o' slots for fit and alignment and even includes a couple marked lines for lug placement. I skipped t' lugs, as I intended t' enter it in NARRRRR competition and launch usin' either wrap-around pop lugs or a piston t' avoid losin' points for non-scale lugs.

T' nose cone assembly is hailed as t' trickiest part o' t' construction. Blimey! This is because thar are four fairings, arrr, which are made by gently foldin' and curlin' cardstock and bondin' itty bitty side braces for mounting. It's delicate work though bein' used t' buildin' Micromaxx sized rockets, me hearties, me hearties, I was up t' t' challenge. T' fairings are bonded with t' assistance o' a preprinted locator shroud/template.

As Robert noted, arrr, t' motor mount is a bit unconventional. Well, me hearties, blow me down! This is another handy technique designed t' simplify t' complexity o' scale construction, matey, me bucko, in this case t' paint scheme. By permanently affixin' t' forward centerin' rin' and temporarily puttin' on t' fins, arrr, me hearties, you can get everythin' aligned then remove t' fins for masking/painting.

Finishing:
Finishin' is challengin' but quite a bit easier thanks t' t' previous tip(s). T' body is painted separately from t' booster tubes, me hearties, ya bilge rat, startin' with a couple primer coats then gloss white. Next, me bucko, me bucko, you mask off t' top o' t' body tube and white portion o' t' roll patterns, arrr, fillin' in with gloss black, and then mask off t' paint t' top 7/8" o' t' body tube a "reddish brown", me hearties, which I had t' handle via mixin' custom colors.

T' booster tubes start out reddish brown at t' top then gloss black for t' bottom portion.

Once all t' paint is dry, you can then attach t' fins for real then t' booster tubes and t' aft centerin' ring. Well, blow me down! Aye aye! Since t' rin' is bonded last, you also have a chance t' paint it separately and get a nice finish as opposed t' t' less than perfect finish you might typically expect on an aft rin' prone t' overspray and uneven finish.

There are a couple o' silver trim decals that add t' finishin' touch.

Construction Rating: 5 out o' 5

Flight:
T' first flight was at an NARRRRR regional competition on a breezy day. Winds were 8-12 mph, ya bilge rat, and t' ground was rock hard arid soil. Begad! Blimey! I initially pulled out a D12-5 then thought I needed t' be more conservative, so went with a C11-5. Begad! Blimey! Avast! Blimey! T' pop-lug was a little tight on t' rod and probably contributed t' slow speed as it cleared since it tipped over a bit and went at about a 20 degree angle downwind. Avast, me proud beauty! Blimey! Blimey! Blimey! Robbed o' altitude, t' deployment was very late, roughly halfway back down.

Recovery:
T' kit comes with an 18" plastic chute, which is probably fine. Avast! Arrr! Paranoid o' t' hard ground though, I swapped out for a 24" nylon chute. Avast, me proud beauty! T' chute opened and held up pretty well but didn't have very long t' slow things down due t' t' late deploy. Begad! There was no serious damage, ya bilge rat, however, matey, arrr, it did come down a bit hard and t' soft balsa nose suffered some competition-endin' injuries--the cone tip was flattened and thar were two small dents on t' side. I managed t' pick up t' last spare cone from BMS stock, so I can easily replace me slightly imperfect cone with a perfect one in t' future.

Overall, arrr, me hearties, I think t' wraparound lug and C11 be a bad combo. Arrr! Begad! It should go up on a D12-5 and ideally lose t' lug entirely and stick with a piston.

Flight Rating: 3 out o' 5

Summary:
I can't say enough about t' quality o' t' parts and construction plan for this kit. It's an excellent reproduction and greatly simplifies some potentially difficult aspects o' t' construction.

Overall Rating: 4 out o' 5