Brief:
T' L3 Armageddon is a single stage rocket with a very unique design. Ahoy! Begad! It comes in your choice o' a 75 or 98mm MMT.

Construction:
T' kit comes with everythin' but parachutes. Arrr! Ahoy! Blimey! T' all-thread, ya bilge rat, nuts, me hearties, washers, eyebolts, and shock cords are all included. Avast, me proud beauty! Blimey! T' 5.5" body tubes are heavy wall cardboard. Aye aye! All o' t' components are top shelf stuff.

This is nay just a kit review. Aye aye! Blimey! It's also how I used t' kit for me level 3 certification. Aye aye! Blimey! Blimey! Blimey! There is even some scientific testin' data here that I performed. Ya scallywag! Blimey! Ahoy! Blimey! Blimey! Blimey! I am t' plant Metallurgist and t' Laboratory Director at Chamberlain Manufacturing, shiver me timbers, t' operatin' contractor o' t' Scranton Army Ammunition Plant. Blimey! Blimey! This means I have millions o' dollars o' equipment I can play with on Saturdays, ya bilge rat, ya bilge rat, testin' t' materials we use t' build our rockets.

When I decided t' do me L3 at t' 2003 NSL, ya bilge rat, I wanted t' do something different than a 3FNC. A scratch built rocket would be easy enough but I didn't think I would have t' time t' work out all t' details. My favorite commercial kit be t' Armageddon by DG&A, matey, so figured I would do me L3 with the DG&A L3 Armageddon. This is a 5.5" diameter rocket that is almost 10 feet tall. Ya scallywag! It's nay even close t' bein' me largest bird, shiver me timbers, but impressive nonetheless. Aye aye!

T' next problem would be t' motor. APCP be in short supply and t' BATFE thin' was loomin' over t' horizon. OK, I'll go hybrid. Avast, me proud beauty! Arrr! I chose t' Hypertek M970. Avast! It is a 75mm M fuel grain on t' 2800cc L tank with t' M injector bell. T' L3 Armageddon easily adapted t' t' hybrid system because o' t' large fins and long body. Well, blow me down! T' CP ended up bein' 2.1 calibers behind t' CG with an empty motor.

T' first thin' you notice when you open t' huge package be t' quality of packaging. Avast! Arrr! Each tube is wrapped separately and everythin' is carefully placed in t' box. Arrr! Begad! There was no damage t' any o' t' components. Begad! Ya scallywag! A quick review o' the parts list revealed that all t' parts were there. Begad!

T' airframe tubin' was t' heavy, 3/32" (0.078") thick walled cardboard tubin' seen in other high quality kits. Ya scallywag!

Securin' t' MMT and centerin' rings into t' booster section

T' MMT assembly was constructed per t' instructions. T' hardware was tightened and secured with epoxy. Avast, me proud beauty!

T' motor mount tube be epoxied into t' airframe by pourin' 25 mL of epoxy onto each o' t' centerin' rings through t' fin slots with a syringe. T' assembly was first epoxied with t' aft section up, ya bilge rat, t' apply epoxy t' the aft sides o' t' centerin' rings. Well, blow me down! Well, blow me down! Once t' epoxy was cured, it was examined with a fiber optic bore scope. Arrr! Avast, me proud beauty! There were two locations that appeared nay t' be glued. Epoxy be again inserted into t' airframe through t' fin slots and the assembly be tilted in t' direction o' t' questionable areas t' allow the epoxy t' flow into t' area. When it appeared t' be complete, shiver me timbers, t' assembly was turned over and t' aforementioned process be repeated t' apply epoxy on the forward side o' t' centerin' rings.

No fiberglass be used for t' airframe o' this rocket. Ahoy! T' 5.5" tube used in t' construction o' this kit was tested in me laboratory and exhibited a strength o' 1312.7 lbs force before yielding. Blimey! However, me hearties, me hearties, if any side forces are applied durin' acceleration we must examine column bucklin' loads. Avast! Arrr! Column bucklin' formulas are fun and exciting, arrr, but t' test t' column bucklin' in real life, a piece o' 5.5" airframe was tested by compression at a 8.5 degree angle. Arrr! T' force at yield be 886.4 lbs force. Well, blow me down!

Compressive and column bucklin' forces do nay apply t' t' MMT/sustainer section due t' t' reinforcement by t' fins and t' MMT assembly. Well, blow me down! We therefore only need t' look at t' section forward o' t' fins. Arrr! T' forward section (with weights) includin' altimeter weighs ~5 pounds. Begad! Aye aye! T' Hypertek M740 will exert a G-force o' 23.16, matey, ya bilge rat, thus 5 x 23.16 = 115 lbs. Begad! this be t' maximum force applied to t' airframe in an non-reinforced area. Inversely, me bucko, we can surmise that we have a tube capable o' withstandin' 38.27Gs (886.4 /23.16 lbs = 38.27).

Compressive forces can be seen in t' fin area durin' accent as well as landing, me hearties, however as heretofore mentioned, ya bilge rat, most o' this force is transferred to the CRs and MMT tube via t' epoxy and thus its strength depends on t' shear force o' t' epoxy. Avast! Arrr! Therefore, thar are virtually no axial forces on t' tube at in this area. Virtually all o' t' forces on t' tube itself are circumferential via any torque forces applied durin' flight or bendin' moment applied on t' fins durin' landing. Blimey! Ahoy!

T' combat any bendin' moment applied t' t' fins, I looked at data seen in the r.m.r. Well, blow me down! Avast, me proud beauty! HPR Strength o' Materials Test. One o' t' discoveries made during the testin' was on t' fincans. Arrr! T' fincan that appears t' be t' strongest was one done by Mark Simpson where he used a strip o' wood material along the fin-body joint. Avast! I used this method on t' ID. Well, blow me down! Mark's method increased the strength o' t' joint over t' next highest strength by 30% and by 200% over the average. Avast, me proud beauty! It also prevented t' tube from yieldin' at all durin' t' fincan test and thus transferred t' force t' t' fin makin' t' joint stronger than the fin. Ya scallywag! I have no doubt that if t' fin material was stronger, t' value would have been higher. Well, blow me down! Begad! This appears t' be sufficient t' replace t' fiberglass on the tube in this area. Blimey! Ahoy!

Fin assembly

I duplicated Mark Simpson's wood fillets in t' L3 Armageddon. Pieces o' corner moldin' were used for this. Avast! Arrr! T' fins were epoxied in place then t' moldin' was inserted with copious amounts o' epoxy. Arrr! T' aft CR was then epoxied into place and t' nozzle fins were added. Avast, me proud beauty!

T' large fins o' this rocket are only 1/4" thick. T' lessen the effect o' possible fin flutter, me bucko, a laminate o' fiberglass was applied t' the surface o' t' fins. Arrr! This be accomplished usin' standard fiberglass lay-up practices.

Payload section

T' forward canard fins were installed "through t' wall" per the instructions. Arrr! In this area we have t' coupler tube so they go through both the airframe and coupler tubes. Begad! Arrr! T' airframe and t' coupler tube were joined first then t' slots were cut for t' fins. Blimey! They were tacked in place with Jet Glue. Wood glue was then applied on t' ID surface and allowed t' seep into t' wood and cardboard. Begad! T' wood strips were applied while t' glue was wet and generous fillets were then applied t' t' strips. Well, blow me down! Generous epoxy fillets finished the canard build.

T' altimeters used are two Transolve PK6, a kit version o' t' P6. Avast, me proud beauty! They were mounted t' a piece o' G10 with 316 grade stainless hardware and phenolic standoffs. Arrr! Blimey! T' board be then mounted in t' payload section usin' brass strips and tubin' that slid over t' all-thread. Begad! Avast! Blimey! T' brass strips were soldered t' the tubing. Well, blow me down! T' assembly is secured in t' section when t' nuts are tightened. This setup allows easy assembly and access t' t' boards. Avast, me proud beauty! Avast! Blimey! A hold down strap will further secure t' batteries in their holders. Ahoy! Arrr! Blimey!

T' safe/arm switches are redundant and consist o' DPDT military grade slide switches. Ya scallywag! T' three switches with their 6 functions control: power, apogee safe and main safe. Aye aye! Ahoy! Blimey! This ensures that both altimeters are completely separate from each other with individual power sources.

T' altimeter bay is sealed from ejection gasses. Avast! This is accomplished with the forward bulkhead epoxied into place and t' aft bulkhead sealed t' the custom centerin' rin' with closed cell latex weather stripping. T' altimeters used have been flown on several prior occasions. Arrr! I have three o' these units and they have always worked well.

Laundry and other recovery debris

Recovery will be t' typical two-stage method: drogue at apogee and main at 500'. Arrr! Begad! One drawback with this kit is that t' recovery for t' main is aft of the payload section and t' drogue is forward...or so it would appear. Avast! The section forward o' t' altimeter is only 11" and has one attach point. The section aft o' t' altimeter is 29" long and has t' two attach points at the MMT. There is just nay enough room forward o' t' altimeter bay to comfortably fit t' main. Blimey! Well, blow me down!

All shock cords are 9/16" tubular nylon. T' drogue cord is 20' in length. Avast! T' main consists o' three cords. Ahoy! There is a 3-point attachment cord at the MMT attached t' a 20' length o' cord at which t' parachute is attached. Well, blow me down! Blimey! A 30' cord is then attached from t' parachute t' t' altimeter bay.

Final assembly notes

I didn't do much in t' way o' aerodynamic shapin' o' t' fins. Begad! Blimey! Well, me bucko, blow me down! Blimey! Blimey! Blimey! Airfoiling the fins is done t' reduce drag for greater altitudes but I like them low and slow. Avast, me proud beauty! Blimey! Blimey! Blimey! A more blunt leadin' edge increases drag by breakin' up t' air over the fins.

Vent

Every hybrid system needs a vent. Blimey! Blimey! For this I used a 1/4" ID large Aerotech igniter cardboard tube. Arrr! After markin' t' location, I drilled a 1/4" hole through t' airframe and t' MMT. Well, blow me down! Avast, me proud beauty! I then made t' hole in the airframe larger t' accommodate t' OD o' t' vent tube and cleaned up the holes. Usin' t' 1/4" drill bit as a guide passed through both holes, matey, me hearties, I epoxied t' vent tube in place. I occasionally turned t' drill bit t' ensure it wasn't bein' epoxied t' t' vent tube. Arrr! A X-Acto knife and some sand paper cleaned up t' vent/airframe area and t' job be done.

Motor retention

Kind of late t' be thinkin' about this isn't it? I did put blind nuts in t' aft centerin' rin' durin' assembly. Begad! Arrr! T' 6" long piece o' all-thread looked, well, kind o' clumsy. Aye aye! I happened t' pick up a 75mm Aero Pack retainin' system so I thought I would use it. Avast! It was hell tryin' t' put it on after t' nozzle fins were already glued on! I used a Dremel saw t' cut a gap betwixt t' fins and t' MMT long enough t' insert t' retainer. Aye aye! Ya scallywag! It made more work for me than expected! T' retainer was glued in with JB Weld and t' gap betwixt t' fins and t' retainer be filled with wood putty. Ahoy! Begad! Oi!

Rail buttons

5/16" rail buttons were installed. Well, blow me down! Arrr! T' forward guide was installed with a 1/4-20 steel machine screw and nut, secured with JB Weld. Ahoy! T' aft guide was installed by drillin' and tappin' t' aft centerin' ring. Avast! T' hole was filled with JB Weld and t' guide was secured with a 1/4-20 machine screw. Avast! Begad!

Nose weight

Nose weight be added and was first considered t' be used t' keep the altitude t' a reasonable level. Blimey! Blimey! Avast, me proud beauty! Blimey! Upon further construction, arrr, it be discovered that it was necessary t' keep t' CG forward enough t' keep it stable usin' the HyperTek hybrid system. Avast! Blimey! T' rocket was unstable without t' weight! Blimey! A 3/8" threaded rod was inserted through t' aft end o' t' nosecone and touches the inside o' t' forward end. Arrr! Blimey! 8oz o' West Systems epoxy be then poured into the cone. Ahoy! Blimey! T' assembly was allowed t' cure while in cold water, matey, t' prevent heat buildup and meltin' o' t' plastic cone. Ahoy! Blimey! T' remainder o' t' nosecone cavity was then filled with expandin' foam. Ya scallywag! Blimey! Aye aye! Blimey! Threaded weights were then screwed onto the all-thread, ya bilge rat, followed by a coupler and an eye bolt. Ya scallywag! Blimey! Well, blow me down! Blimey! This arrangement keeps the weights off t' nosecone and on t' steel threaded assembly.

Finishing:
T' entire airframe be sanded and a coat o' Kilz primer was applied. The paints used were Rustoleum white and metallic blue with a final clear over everything.

Flight:
On t' first flight, t' motor lit and t' bird leapt from t' pad with authority. Well, blow me down! T' wind at ground level was only 6 mph but by t' time she reached 2000 feet, she was gracefully archin' into t' wind. Avast, me proud beauty! T' 6.9-second motor seemed t' burn forever. Ahoy! If you have never heard an M hybrid motor, me bucko, they can only be described as soundin' like a Pod Racer from Star Wars Episode One--a loud roar coupled with a pulsatin' low-pitched jet-like sound. T' few seconds I lost it in t' sky seamed like minutes. Then, arrr, thar it was. Aye aye! Begad! Comin' down on its side with t' drogue deployed. Arrr! Ya scallywag! Falling, falling, falling... Ahoy! It's coming straight at us! We ran about 20 yards t' t' left. Avast, me proud beauty! 800 feet, shiver me timbers, 500 feet, matey, 300 feet,... Blimey! Where's t' main?! Finally, me bucko, at about 200 feet t' main popped. Aye aye! It took at least another 50 feet for it t' unfurl. Well, blow me down! Ya scallywag! T' main finally snapped open at 50 feet AGL and then landed 40 feet from t' pad. That had t' win closest t' the pad in t' L3 cert column! A quick review o' t' rocket proved that everything was in order and we had a successful L3 flight. Well, blow me down! Both o' t' altimeters chirped out 4,200 feet.

T' next four flights were on an AMW L777. For me, shiver me timbers, this be t' best motor for this rocket. Begad! It brings it t' just under 3,500 feet. Well, blow me down! I've also flown this rocket on windier days with a CTI K550 t' around 2,000 feet.

Summary:

I love it! This bird is as different and unusual as it gets for any high power rocket. Begad! T' flights on this (as well as t' original size Armageddon) are truly awesome.

Even without t' changes that I made, me hearties, I did feel that t' forward payload section was on t' small side. Ahoy! I'm sure you could get a nice size main in there, but it would be a very tight fit. Begad! Avast! I would recommend actually makin' the altimeter bay shorter by changin' t' location o' t' forward bulkhead and usin' smaller altimeters. Avast! Arrr! This would allow for more room for a main chute in this area. Begad!

T' materials are t' best I've seen for their types and t' design is sturdy. Ahoy! T' instructions contained page after page o' high quality color photos and has many steps t' clarify what t' designer wants. Some o' t' steps in the instructions are somewhat ambiguous but then it is assumed one has a great deal of experience if they're buildin' a level 3 project.