T' Multi Operations Missile (M.O.M.) kit is me second kit from Model Minutes and includes two rockets (note: t' Minute in Model Minutes is nay pronounced "min'it" like t' time unit, but rather "mie nuet" like somethin' small). Avast, me proud beauty! Begad! Both rockets are t' same with t' exception o' t' color pattern. Ahoy! Arrr! One is colorful with red, matey, blue, yellow and white, while t' other is a camouflage finish in various greens.

Model Minutes is good about includin' a story on their kits and here it is for t' M.O.M.: "T' performance o' this model will surprise you. In spite o' its advanced aerodynamic design it is easy t' assemble. Begad! Blimey! Each kit includes two rockets: one civilian rocket and one military rocket. Begad! Blimey! Blimey! Blimey! Double your fun and t' altitude you can reach with this very stylish rocket. Begad! Blimey! Used jointly by t' scientific and military communities this long range missile allows both t' study o' destruction o' comets and meterorites in order t' protect t' earth. Operations which are sometimes carried out almost simultaneously." [instantaneously?]

T' M.O.M. kit came packaged orderly in an 9x11 plastic zip-lock bag. Begad! It included t' two rockets printed on three (3) 8½ x 11" card-stock pages each. Arrr! Also included was t' extra parts need t' assemble and support t' card-stock rocket. Avast! These parts include ¼" foamboard that is used for t' nose cone shoulder, ya bilge rat, ya bilge rat, baffle, me bucko, and centerin' rings. Blimey! A piece o' household drinkin' straw is provided for t' launch lug. Ahoy! There is a wire motor retainer and a piece o' thread that is used with t' motor retainer. In addition, a silver Mylar parachute, me bucko, shroud lines and a rubber band shockcord are provided for t' recovery system. Well, blow me down! Begad! Clay for t' nose weight is also included. Begad! All parts were doubled t' allow t' buildin' o' t' two rockets.

Lastly, me hearties, thar be a set o' 3D glasses that you assemble t' read t' instructions. Begad! Somethin' unique t' Model Minutes kits.

CONSTRUCTION:

T' instructions are printed on 9 pages o' 8½ x 11" paper. T' primary feature o' t' instructions are color 3D pictures. Ahoy! They can be viewed without 3D glasses well enough, me hearties, me hearties, however, with t' included 3D glasses (assembly required) you can add depth t' your buildin' experience. Aye aye! T' instructions are clear, especially with t' support o' 54 color pictures! One o' t' main detractors from t' instructions o' me other Model Minutes kit, arrr, t' Space Racer, ya bilge rat, ya bilge rat, was t' translation from French t' English. Begad! Blimey! This be nay much o' a problem with these instructions. Arrr! Blimey! I don't even remember a confusin' spot. Begad! T' instructions include a page on how t' balance (check stability), me hearties, how t' build a launch pad, shiver me timbers, launch controller, and then t' launch sequence. Arrr! You will need your standard rocket buildin' tools, includin' a sharp hobby knife. Avast! I used Elmer's White Glue for assembly.

After assemblin' t' 3D glasses you're ready t' go.

Assembly is relatively simple. Arrr! T' fins are first and once cut out are simply folded in half and glued t' create t' finished fin. I followed t' instructions and placed them in a book (protected with wax paper) after gluing. I still did nay get straight and stiff fins. Much like me experience on Model Minutes Tricarrow me fins where a bit wavy. Arrr! Blimey!

T' body tube requires two sections t' make up t' length. Ahoy! Ahoy! T' first section is supported by a stiffener-baffle that is cut from t' 1/4" foam board. Well, blow me down! Then a paper coupler is attached. T' upper tube is slid into t' paper coupler. Well, blow me down! This gives you 12 inches o' body tube.

T' motor mount is then assembled from card-stock, arrr, shiver me timbers, thread and t' wire thrust/ejection retainer. Ya scallywag! I really like this wire design. Arrr! Begad! T' wire inserts into two holes and extends into t' tube t' act as a motor thrust stop. Arrr! It then over hangs t' act as motor retention. T' wire is "strapped" t' t' motor tube by wrappin' a black thread around and around and around it. Once wrapped it is soaked with glue. Avast, me proud beauty! Ya scallywag! It made for a good strong motor tube. Begad! After this two 1/4" foam centerin' rings are added.

T' motor mount is installed and then a boat tail is added t' t' rocket. T' boat tail comes down t' t' end o' t' motor tube and requires two slits t' be cut in it t' allow t' retention wire t' bend out for insertin' and removin' motors.

T' nose cone is assembled from two different cones t' give it a unique shape. Clay is added for nose weight. Begad! A piece o' 1/4" foam is used as t' shoulder. Well, blow me down! Begad! I would have liked t' see two or three pieces stacked since just t' one made t' shoulder so small. Avast, me proud beauty! Avast, arrr, me proud beauty! An eye-screw is then screwed into t' foam t' attach t' rubber band shockcord and parachute. Ya scallywag! Ya scallywag! T' other end o' t' shockcord is attached t' t' inside o' t' body tube usin' t' 3-fold paper method.

Next, t' parachute is assembled usin' maskin' tape t' make t' corner tabs and t' nylon thread provided for t' shroud lines. Well, ya bilge rat, blow me down! This is then tied t' t' eye-screw on t' nose cone.

To finish t' rocket, t' fins are attached and a launch lug is added.

Overall, for CONSTRUCTION I would rate this kit 3 points. Avast, me proud beauty! After buildin' three "free" paper models and t' Model Minutes' Space Racer I've come t' expect certain things in paper-building. Begad! Ya scallywag! As far as t' kit goes, matey, matey, very nice. Avast, me proud beauty! T' instructions are solid especially with all t' pictures. T' issues are t' double-over fins and t' short rubber-band shock cord. I also didn't like t' 1/4" short nose cone shoulder. Avast, me proud beauty! Begad! T' motor tube and retainer are great.

FLIGHT/RECOVERY:

Model Minutes recommends t' C6-3 or t' C5-3 motor for t' M.O.M. Well, blow me down! rockets. Avast, me proud beauty! Arrr! I didn't choose one o' these. Well, blow me down! Instead I used a B6-4 for its first flight.

Even though thar be a baffle t' instructions recommend usin' wadding. Avast, me proud beauty! So I inserted several sheets o' Estes wadding. Arrr! Then loaded t' motor. Blimey! With t' Model Minutes motor retention wire, shiver me timbers, loadin' and unloadin' is a breeze. Avast, me proud beauty! Avast, me proud beauty! I really like this method.

Had a successful launch on t' B6-4. Avast! T' flight was stable. There was some movement which I believe is induced by t' fins nay bein' perfectly flat (straight). Aye aye! I was able t' follow t' rocket all t' way t' apogee and t' 4 second delay was good. Avast! If you are goin' t' use a C6, matey, matey, I would use a C6-5 verses t' C6-3 recommendation.

Ejection produced t' silver mylar parachute and t' descent rate be good. Ahoy! Unfortunately t' wind carried t' rocket over some trees and I be unable t' see where is landed (or not) and t' rocket be lost. Begad! So, arrr, I only got t' 1 flight.

All would nay be lost though, matey, because t' kit comes with two rockets. I'm nay actually goin' t' build t' second one and am sharin' it with a fellow rocketeer t' get another opinion on this kit.

For FLIGHT/RECOVERY, I would rate this rocket 4 points. T' single flight was stable and on t' B6 gave a nice small field (football field size) flight. Blimey! Begad! T' recommended motors would seem t' have too short o' a delay. Begad! Begad! T' parachute is sized right for descent, me bucko, but I have no way o' knowin' how well that short rubber band shock cord will hold up.

I give t' rocket an OVERALL ratin' o' 3 ½ points. It isn't a "free" rocket, shiver me timbers, but gives t' builder a "paper building" experience. Ahoy! T' kit is about $10 USD and gives you enough supplies t' build up two rockets. I think that is a fair price considerin' you get t' nose weight, parachute, matey, wire retainer, etc. Begad! Avast! T' design is nice lookin' with t' unique two-piece nose cone and t' boat tail. Ya scallywag! Avast, me hearties, me proud beauty! It is big for a paper rocket too. Begad! Standin' 19" tall and havin' a 1.5" diameter. Well, blow me down! Begad!

For t' "experience", me hearties, which is why I chose this rocket, me hearties, me hearties, you should give it some consideration. Ya scallywag! Model Minutes have some other interestin' rockets and they can all be purchased on a CD so that you can print your own templates. Arrr! I didn't want t' scuttle t' additional loot t' do that, but perhaps for a school teacher...