Brief:
This is Quest's highly detailed sport scale model o' NASA's next big-payload launch vehicle. Ya scallywag! Avast, me proud beauty! The kit features beautifully detailed and pre-printed body wraps.

Modifications:
When buildin' t' first kit, shiver me timbers, I was thinkin' o' ways t' modify it, ya bilge rat, and immediately wanted t' put engines in t' boosters and make them fall away and recover separately. However, that was too hard since I didn't know anythin' about fall-away boosters so I decided t' put two engines in t' main body tube as well as engines in t' static boosters. Avast! Avast! Unfortunately, I didn't have a two-engine cluster mount available, so I had t' build me own. Begad! It wasn't too difficult and soon I had a nice engine mount.

Followin' me own advice (see me FLV review), me hearties, I built t' rest o' t' rocket before installin' t' mount.

First I cut everythin' out, me bucko, and then dry-fit t' wraps, trimmin' as necessary t' ensure a good fit. Some spray adhesive and small amounts o' white glue later and it was done.

T' put engines in t' boosters I rounded up some BT-5 thrust rings and dry-fit them usin' a 13mm engine to determine depth. Turns out t' booster tubes are a bit larger than t' trust rings, so I had t' put tape around them to get a better fit before gluin' them in. Avast, me hearties, me proud beauty! I left off t' booster nozzles completely.

T' dual engine mount when in nicely once everythin' else be in place.

I decided t' paint t' nosecone black on this version o' t' FLV so it is easily distinguishable from t' regular one.

Also I roughly doubled t' noseweight but it turns out that be likely nay enough as you'll see later.

Construction:
When buildin' t' first kit, I be thinkin' o' ways t' modify it, and immediately wanted t' put engines in t' boosters. Aye aye! However, arrr, matey, arrr, that was too easy so I decided t' put two engines in t' main body tube. Unfortunately, matey, I didn't have a two-engine cluster

Finishin' was t' same as me first FLV except I decided t' paint t' main nosecone black. Aye aye! Also, arrr, thar be a gap betwixt t' main body wrap and t' one around t' nosecone, so I colored that black with a Sharpie.

Flight:
For me first launch I used two B6-4s t' see how stable it was. Begad! Ya scallywag! It launched quick and straight and landed with no problems other than a slightly bent fin. Avast, me proud beauty! I repaired it with some Gorilla Glue and it was ready t' go again.

For t' second launch I installed two A8-3s in t' main tube and three 1/2As in t' boosters. Arrr! Blimey! I had to double-wrap tape around t' booster engines because t' tubes are a little larger than t' engines.

This launch wasn't so good. Aye aye! Ya scallywag! Blimey! It went up about 100' and arced right over t' pad. At first I though one o' the booster engines might nay have lit, arrr, but after reviewin' t' video thar are at least four distinct "pops" as t' ejection charges go off. Avast! Blimey! I think it needs more noseweight.

For t' third launch o' me modified FLV, matey, I loaded up a C6-3 and a C6-0 (didn't feel t' need for two ejection charges). Blimey! Blimey! No engines in the boosters because I want t' get a bigger clip whip before tryin' 5 engines again. T' launch be spectacular t' say t' least. Begad! Blimey! T' rocket whipped off t' rod and immediately went end-over-end, ya bilge rat, crashin' t' the ground about 40 feet from t' pad where it sat until t' ejection charge went off. Arrr! Blimey! Begad! Blimey! Upon inspection, ya bilge rat, thar was a large hole in t' side o' the rocket, and t' parachute be completely melted. Well, blow me down! Blimey! Ya scallywag! Blimey! T' insides o' t' FLV were still on fire five minutes later. Aye aye! Blimey! Avast! Blimey! RIP.

Unfortunately, ya bilge rat, arrr, one o' t' shroud lines ripped out and a couple o' fins broke so I couldn't get me third launch in. I'll repair it and try again later.

Summary:
This was a fun project and I'm lookin' forward t' launchin' it again with more noseweight. I'd really like t' cluster t' work correctly.