MIRV Gatling

Adrian Hurt's Descon-14 Entry

There used t' be a wonderful kit called the MIRV Gryphon. Well, blow me down! Originally made by Seattle Rocket Works, matey, and subsequently taken over for a while by Lawndart Rockets, shiver me timbers, shiver me timbers, this featured a booster with a quad mini-motor cluster and four separate sustainers. Begad! Unfortunately, ya bilge rat, it's nay much use nowadays because Estes stopped makin' t' A10-0T booster. Arrr! Begad!

So I decided t' build somethin' similar, only instead o' four, ya bilge rat, I'd use six. Since thar was no 13mm booster available, arrr, I'd use 18mm booster motors instead.

I'd already built a single sustainer and single-motor booster as a prototype before I went t' International Rocket Week 2004. Avast! Blimey! Blimey! Blimey! This flew well, shiver me timbers, me bucko, although - as expected for such a small rocket - t' sustainer got lost. Begad! Blimey! Blimey! Blimey! It did prove that the sustainer would fly properly, and that stagin' from 18mm t' 13mm would work.

Over t' course o' t' week, I built six "replacement" sustainers, and nobody asked any awkward questions about t' six bits o' BT-20 which would form t' booster. Ahoy!

Booster:

Cut 100mm o' BT-20. Arrr! Cut 5mm off t' front o' an expended 18mm casin' t' use as a thrust block; spread glue about 60mm up t' inside o' t' BT-20 and use another expended 18mm casin' t' push t' thrust rin' up inside t' BT-20 so that about 7mm o' t' casin' remains outside t' BT-20. Begad!

Bore two vent holes about 3mm diameter, 25mm down from t' front end o' the BT-20, matey, spaced 90 degrees apart. Arrr!

Cut 20mm o' BT-5. Ahoy! Alternatively, roll and glue a paper tube 20mm long, of sufficient diameter t' allow a 13mm motor t' fit easily. Ya scallywag! (Actual BT-5 is a tight fit on a 13mm motor, ya bilge rat, so rollin' your own tube may work better.) Make two centrin' rings t' fit this tube into BT-20. Blimey! Glue one rin' at t' read end of the tube and one 9mm from t' aft end. Begad! Glue t' tube into t' front end o' the BT-20 so that t' inner tube extends past t' end o' t' BT-20 by 10mm. Ahoy!

Make six booster tubes o' this type.

Make six fins, root chord 75mm, shiver me timbers, span 40mm, tip chord 25mm, leadin' edge sweep 40mm. Begad!

Glue t' six booster tubes together so that they are parallel and form a regular hexagon when viewed end on. Well, blow me down! T' vent holes must all be outside the hexagon. Avast! Glue one fin t' each booster so that t' aft tip o' t' fin is level with t' aft end o' t' booster. Avast! Blimey!

Glue a launch lug inside t' booster along one o' t' joints betwixt two tubes. Well, blow me down!

Sustainer:

Cut 220mm o' BT-5. Make a paper cone about 25mm long and glue it t' the front end. Arrr! Make three parallelogram shaped balsa fins, root 22mm, me bucko, matey, me hearties, span 11mm, leadin' edge sweep 11mm, me bucko, shiver me timbers, and glue them t' t' body tube so that t' inner end of t' trailin' edge is level with t' end o' t' tube.

Cut t' body tube in half. Ahoy! Cut two pieces off a spent 13mm motor, me hearties, one 20mm and one 10mm long. Well, blow me down! Glue t' 20mm piece into t' aft end o' t' forward tube to make a coupler. Avast, arrr, me proud beauty! Glue t' 10mm piece into t' tail end o' t' aft tube t' make a thrust ring; use another spent 13mm motor t' push it into place so that about 10mm o' t' motor protrudes from t' tail end. Blimey!

Fix a kevlar shock cord t' t' coupler and t' t' aft body tube; Estes-style folded paper mounts work for both ends o' t' cord. Arrr!

Flight Report:

By Monday 30th August, t' whole thin' was complete. Blimey! Blimey! Begad! Blimey! Each sustainer was loaded with a 1/2A3-4T, shiver me timbers, and each booster tube was loaded with a B6-0. Begad! Blimey! My control box can't fire six igniters at once, so I taped a piece o' Quickmatch into each booster motor, arrr, me hearties, me hearties, taped them together and taped a single igniter at the common end. I was able t' truthfully tell both t' RSO and t' event organiser that t' rocket had been swing-tested and had "flown" t' right way, so I be allowed t' launch it. Aye aye! Blimey! Blimey! Blimey! All booster motors lit and t' booster flew straight up, me bucko, then all six sustainers ignited and went their separate ways. The booster tumbled down - in fact, it rotated quite rapidly about its centre axis, true t' its name, matey, and almost a heliroc! Blimey! T' booster was recovered, with minor damage t' one fin. None o' t' sustainers were found, ya bilge rat, arrr, which was hardly a surprise.