Brief:
Aerotech's take on t' often modeled Navy Standard ARM be t' "Strong ARM". It's nay a particularly close scale rendition, shiver me timbers, but t' result is good lookin' and well suited t' F and G motors, particularly t' EconoJets. There's a bit more t' build in this kit than in t' Aerotech Initiator or Mustang, but nay so much that builders new t' mid-power should be scared away. As mid-to-high power kits go it's still quite easy, me hearties, especially if you work carefully and watch out for a few 'gotchas' that I will detail later.

Construction:
This is a single stage rocket with two body tubes joined with a coupler, 4 fins, and parachute recovery. Well, blow me down! Begad! This kit uses t' same Fin-Lok system and baffle unit you find in all Aerotech kits. Ya scallywag! It's a medium sized rocket for Aerotech, 44 inches long and about pound and a half in weight when loaded for flight. Well, blow me down! The Aerotech catalog, btw, ya bilge rat, lists t' weight o' t' rocket as 18 oz., but I don't know how they could get this weight. Avast! Somethin' betwixt 22oz t' 25oz, seems more realistic.

This was t' first kit I built from this manufacturer, me bucko, though I have built other rockets o' this size. I was eager t' see how t' famed Aerotech Fin-Lok system and baffle unit worked. Aye aye! I was also lookin' t' get a new F and G motor bird in t' fleet smartly and easily. Begad! I went t' t' Strong ARM thinkin' I'd have an relaxed time o' it. As it turned out t' construction was quite a bit more involved than I anticipated, arrr, but this does nay have t' be your experience, I just ran into some potholes along t' way. Begad! In truth I have faced tougher challenges, and I did end up with a great rocket, but I was expectin' something different.

T' rocket arrives in a sturdy box that can become a display stand (nice!). T' tubes are sturdy and pre-slotted, t' fins are preformed. T' engine mount parts are all thar and seem well constructed. Begad! Blimey! Aye aye! Blimey! T' engine clip is big and strong! Blimey! T' parachute is very nice, shiver me timbers, and t' nosecone is...well, ya bilge rat, this be the first disappointment. Begad! Blimey! T' nosecone be a real mess. Easily t' worst formed part I've ever experienced, from any manufacturer. Ya scallywag! Blimey! I have seen other comments on Aerotech cones from others, me bucko, but most folks are happy with theirs, matey, so I think this is a quality control issue. Begad! Blimey! Ahoy! Blimey! If you get a good one, me bucko, matey, shiver me timbers, your doin' fine. Aye aye! Blimey! Ya scallywag! Blimey! If you get a bad one you have t' decide how t' handle it. Arrr! Blimey! I suspect that if you raise enough o' a stink with Aerotech you can get a replacement. Blimey! Blimey! I didn't fully appreciate how much trouble this nosecone would give me when I first inspected it, so I elected t' try t' fix it (I did write Aerotech about it, though). Begad! Blimey!

T' generally excellent instructions have you start with t' motor mount. This is where you will see t' first signs o' Aerotech's particular design philosophy. Ahoy! Begad! They design their kits t' carry loads through t' structure, and their rockets are therefore less reliant on heavy applications o' glue (this from their documentation). Begad! Well, blow me down! I like this idea, but you will find that it has one downside; t' rocket components must be built with very tight fits and close tolerances. Ahoy! Blimey! T' Aerotech corollary t' t' old sayin' "measure twice, matey, cut once" is "test fit twice (or more), me bucko, glue once". Arrr! Begad! T' best advice I can give you is, me bucko, "don't touch that glue until you are absolutely sure how this part, matey, me hearties, ya bilge rat, and t' parts that follow, shiver me timbers, will fit, shiver me timbers, ya bilge rat, and have verified that they do fit!" Read all t' instructions before you start, ya bilge rat, and perhaps go t' the Aerotech site and view t' video o' an Initiator construction, me hearties, ya bilge rat, so you know what to expect.

Aerotech recommends that you build t' rocket with medium CA, and I wanted to give that technique a try. I've never used CA in such large amounts on such large parts, and it takes some gettin' used to. Well, blow me down! You start off easy with the 24mm engine adapter, arrr, which is just a tube and two rings or sleeves. Avast! Aye aye! Blimey! Aerotech provides a markin' guide for t' main motor tube, me bucko, me hearties, which is a nice touch. Begad! Blimey! You need t' be careful about keepin' your "front edges" and "back edges" straight at this point. Aye aye! Well, blow me down! Blimey! It can get confusin' but it's important, arrr, so read t' instructions very carefully and take it slow. Well, blow me down! Blimey! Blimey! T' industrial size motor hook installs just like an Estes hook.

Now comes t' first tricky part. Blimey! Blimey! T' instructions tell you t' put "several drops" o' glue "just behind where t' motor clip comes through t' tube". Believe what they say. Blimey! Blimey! Use a small amount o' glue and be sure t' place it up next t' t' hook (also note that t' motor block comes into t' tube from t' back or nozzle end, this be t' reverse o' t' usual Estes procedure with engine hook equipped models). Ahoy! Blimey! T' engine block fits tight in t' tube, and you need t' get it all t' way up t' t' hook before t' CA glue 'grabs'. Well, blow me down! Blimey! CA does nay give you any chance t' ease things into position once it starts t' set. Avast! Blimey! And it sets quick when t' fit is tight and thar's friction.

T' next step be t' initial fit o' t' Fin-Loks and centerin' rings. No glue at this stage, matey, you need t' test fits and positionin' first. Aye aye! T' fit is very tight, as mentioned above, but that's an important part o' how t' Fin-Lok system works. Arrr! Well, blow me down! You check everythin' by snappin' t' fins into position in the Fin-Loks. Aye aye! It takes some force t' get them in place, matey, but you should feel and hear a definite "click" as it seats. This is a good time t' get used to t' 'feel' and force required. Blimey! Aye aye! Once all t' rings are properly placed and aligned, me bucko, me bucko, remove t' fins (carefully, matey, don't move t' Fin-Lok rings!) and apply a very slight bead o' CA t' t' Fin-Loks and front centerin' ring. Ya scallywag! The instructions are pretty insistent that you take great care t' keep glue out of the Fin-Lok channels (where t' fin will go). Again, me hearties, matey, me hearties, believe what they tell you! CA is pretty low viscosity stuff, and it can flow around as you rotate the part. Avast, me proud beauty! Begad! T' clearances are very tight an even a small amount o' glue will cause havoc. Well, arrr, blow me down!

Once t' glue has set on t' rings (pretty quick with CA), me bucko, you get t' build the baffle, which is fun. Arrr! Ya scallywag! T' "steel mesh" gets stretched out t' six inches, then it slides into t' tube, you cap t' tube with a plastic baffle unit, add a third centerin' rin' and screw an eye bolt into t' baffle unit. T' shock-cord ties t' t' screw eye. Begad! Avast, me proud beauty! Easiest baffle I've ever built, and I like baffles. I have seen a Strong Arm (not mine thank goodness!) destroyed when t' shock cord attachment separated at apogee. Either t' cord broke, arrr, came untied or t' screw pulled out, I did nay hear t' final verdict. In any case, this be t' time t' make sure you have a solid attachment. Avast, me hearties, me proud beauty!

Now it's time t' place t' motor and fin mount into t' body and attach the fins. Aye aye! Aye aye! You slide t' mount into t' pre-slotted end o' t' body tube, matey, but do not glue it yet. Avast! Aerotech would like you t' glue t' fins into place with CA "along t' full length o' t' fin root" first. Begad! I'm goin' t' suggest that you add a step. I did as I be told and, shiver me timbers, snapped one well glued fin into place. Well, blow me down! "Wow, shiver me timbers, shiver me timbers, that was easy!". Aye aye! Then I decided t' attach t' fin directly opposite t' first, as I could push on t' fin (and hence on the attached Fin-Lok rings) and nay t' body tube. Ya scallywag! Once you get a bead o' CA down the length o' your fin you tend t' move quickly, ya bilge rat, t' stuff sets fast! I slid the fin into place and pushed and..nothing! No "click". Begad! Well, blow me down! I pronounced a few expletives (that always helps) and gave it a harder push. Well, on the third push somethin' happened, but it wasn't t' Fin-Lok click I be looking for. Ya scallywag! Blimey! T' motor mount, remember, is nay glued into place at this point. It's free t' rotate in t' tub! e, and that's what mine did under t' considerable compression force I was exerting. Ahoy! That rotation caused t' fin tabs on both fins t' snap at their weak point (between t' two Fin-Lok 'ridges' (It's tough to describe but obvious when you see it). Avast! Thankfully, me hearties, ya bilge rat, me bucko, this happened late at night when t' kids were asleep, arrr, so they did nay hear me "comment" on these events.

I was nay aware, arrr, me bucko, at that time, arrr, that you can buy these fins separately from Aerotech, me bucko, arrr, me bucko, and I was mad at this kit and nay ready t' be "defeated" by it, matey, arrr, me bucko, so I removed t' bottoms o' t' fin tabs from t' Fin-Loks with pliers (CA is strong but I'm stronger!) and repaired t' fins. They are probably nay as strong as before but they're close. Aye aye! Blimey! I tried dry fittin' t' fins and one was clearly never goin' t' snap into place. After a while I realized that t' fin would seat in t' 'lok' when t' mount was out o' t' body tube, ya bilge rat, but would not when t' mount was in t' tube. Slowly a light went on. Avast! I snapped t' fins into place with t' mount in me lap, me hearties, and saw that one fin was tight against the centerin' ring. Begad! T' added thickness o' t' tube kept t' fin from seating properly. Avast, me proud beauty! Blimey! I sanded down that side o' t' centerin' ring, arrr, arrr, tested until I got all four fins dry-fit into position, ya bilge rat, and then finally glued them into place. Blimey! Begad! Blimey!

Here's what I suggest you do. Begad! Once t' glue has set on t' Fin-Lok rings and centerin' ring. Avast, me proud beauty! Give t' fins another dry fit test. Ahoy! Blimey! I think I also had a very small amount o' CA get into one Fin-Lok, and its important t' catch that problem before you are gluin' t' fins. Well, blow me down! Begad! Then slide t' mount into t' body tube and dry fit again! Once all t' fins fit nicely in t' tube you are home free. I would pull t' fins out one-at-a-time t' glue them. Avast! Leave t' others in place to support and stabilize t' mount. Well, blow me down! Arrr! This sounds like a lot, but if your parts fit right it will add very little time, just a minute or two. Avast! Avast! If you have a problem, arrr, this will save you a lot o' anguish. Avast! Any problems you discover at this point can be easily fixed, but if you blast ahead like me you court disaster (or at least a lot o' extra effort.and expletives!)

Once t' fins are on you reach in through t' open back o' t' rocket to glue t' motor mount in place and apply internal fillets t' t' fins. Aye aye! (I have to admit that I resorted t' epoxy with micro-balloons at this point). Then you join t' body tubes with a very ample tube coupler. Avast, me proud beauty! This is another place where CA can trip you up. T' coupler tube is very tight in t' body tubes, and the glue can set and grab before you get t' tubes fully in place. Well, blow me down! It happened to me when I brought t' top tube down onto t' lower tube and coupler. Aye aye! Ahoy! I have over 200 pounds on me t' contribute t' t' effort and I was puttin' all the weight I could on that tube t' slide it down, arrr, but it still grabbed about ¼ inch short o' t' bottom tube. I eventually filled t' gap with a combination of wood filler painted with CA and a bit o' epoxy putty. Ya scallywag! Blimey! It looks fine, matey, but you don't want t' go through that. Arrr! T' instructions suggest a bead o' CA about an inch inside t' upper body tube. I would place t' glue farther in or, shiver me timbers, even better, use wood glue for these joints. Avast, me proud beauty! Avast, me proud beauty! It will be stronger and easier t' work with (but it can still 'grab' early if you move too slowly, shiver me timbers, especially on tight fits like this!)

T' "fin strakes" that give this rocket its "ARM" look must be shaped a bit. Begad! T' instructions give you t' dimensions very clearly. This is more t' sort o' thin' I am used t' and it went well for me (finally!). I would suggest that you measure and mark each strake carefully, me hearties, then cut with a carpenter's knife. Avast, me proud beauty! I needed several passes t' make each cut. Aye aye! Aye aye! T' strakes can be sanded somewhat t' smooth t' edges but they are nay easy t' shape that way, you really need t' knife (or perhaps a Dremel). I held off gluin' the completed strakes on t' body until I had finished fillin' and sandin' t' body tube, and I suggest you do too. Aye aye! It makes t' sandin' a lot easier.

T' strakes mount on t' tube with CA and t' launch lugs drop into pre-cut holes. Ahoy! So far everythin' has stayed on t' rocket.

Finally I turned me attention t' t' nose cone. Aye aye! Begad! I'll spare you all the details, me bucko, and just mention that I spent three evenings workin' with a power orbital sander held betwixt me knees (wow, that tingles!) usin' 100 grit paper to smooth t' surface o' this cone. Begad! Begad! Out o' t' box it looked like t' surface of a basketball, shiver me timbers, arrr, or a cantaloupe melon. Begad! Begad! T' tip be a mass o' swirlin' grooves and t' seam was quite deep. Begad! I should have sent it back t' Aerotech, arrr, but my stubbornness be up and I attacked it with a fierce determination. Avast! Arrr! I emerged covered in white plastic dust holdin' a great lookin' nose cone. Begad! Aye aye! This one ranks up thar with t' nose cone o' t' Quest Nike Smoke as "most painful". Aye aye! Begad! In both cases, however, matey, arrr, I managed t' achieve a good result. Persistence pays! I touched up t' surface with progressively finer grades of paper and declared t' construction phase over!

Finishing:
T' finishin' process was pretty painless. Aye aye! I used several coats o' gray primer, with light sanding, arrr, arrr, followed by a couple o' coats o' glossy white. I had filled the spirals with Elmers wood filler and t' final surface looked pretty good. Aerotech suggests a gray nosecone, me bucko, matey, but I had another idea. Many photos o' the real missile show a coppery lookin' nose, which looks good t' me. Well, blow me down! I got a can of Testors copper for t' nose and am very happy with t' result. Avast! If you use these metallic paints just remember t' apply light coats (even more important than with other paints) and don't judge t' looks until it all dries, matey, it can look uneven when wet. You should also use clear coat t' protect it, arrr, as the metallic finish can scuff easily. Arrr!

T' kit comes with plenty o' stick-on decals. Avast, me proud beauty! It will take a while t' get them all positioned, matey, but t' instructions give you good guidance. Avast! Begad! T' clear coat helps protect them as well. Ya scallywag! It's a good lookin' rocket; dress it up right.

Construction Rating: 4 out o' 5

Flight:
I have only flown it on F20-4 Econojet motors so far, but this is a great motor for this bird. Boost has been straight (despite wind) and higher than I expected, matey, around 750 feet or more. Blimey! This is just right for our field. Avast, me proud beauty! I would like t' try it on t' G Econojets but I can't find any in t' current shortage. Aye aye! T' four second delay seems about right; I certainly wouldn't try it with a seven second delay. Well, blow me down!

That beefy motor clip takes some effort t' pull back. I use a pair of pliers t' hold t' clip while I insert and remove t' motor. Arrr! It's nice t' know that that motor is well restrained.

Recovery:
Aerotech provides a very nice 30 inch chute which brings t' Strong ARM down gently. Begad! I have had some drift with mine (windy conditions) and will either reduce t' chute when I fly with a G, matey, or wait for calm winds. Avast! Begad! There is no need for waddin' due t' t' baffle, ya bilge rat, me bucko, which has worked fine for me (you never notice a baffle unit until it fails). Ya scallywag! Blimey! I have no complaints about t' recovery system. Ya scallywag!

Flight Rating: 4 out o' 5

Summary:
I bought t' Strong Arm hopin' for a fast, arrr, easy build; kind o' a 'vacation' from t' more challengin' projects. Begad! Blimey! I got t' good lookin' and good flying rocket I expected, but t' build process had its frustrations, as I have described. Avast! Blimey! In t' grand scale o' things this wasn't really so bad. Avast, me proud beauty! Blimey! I've had scratch projects get much hairier, but I expected different from an expensive kit like this. Well, blow me down! Blimey! Arrr! Blimey! T' nosecone was just a crummy part. My other problems resulted from me unfamiliarity with t' Aerotech system and with CA as t' primary adhesive. Many people I trust have built multiple Aerotech kits without any trouble at all, and when I build another I'm sure I won't have any either. Arrr! Blimey! I'll test fit t' fins at each step and be careful with t' CA.

Now that I'm smarter about Fin-Loks I like t' idea, me bucko, me hearties, and t' baffle is good one. Any o' t' Aerotech kits are good choices for a first "high-power rocket" (really "upper mid-power"). Begad! Blimey! I like t' look and size of the Strong Arm best. Ahoy! Blimey! If you are careful and mindful o' t' warnings in the instructions you'll do fine. Ahoy! Blimey! (.and go with copper for t' nose cone! Blimey! Gray is much too borin' for a cool rocket like this!)

Overall Rating: 4 out o' 5

The followin' excerpt is from "Sport Rocketry". Avast! T' intention is t' allow guests t' get a basic feelin' about a kit. Well, blow me down! Aye aye! Blimey! We strongly suggest that you get a copy o' t' referenced Sport Rocketry and read t' entire article. Blimey! Blimey! Inside you will find many helpful hints in construction as well as other useful information. For more information, use t' two links above.

"Over t' past few years I have found Aerotech rocket kits fun t' build and fly." 
"Lookin' over t' parts, I found everythin' in good shape except for one of t' fin lock rings. Ahoy! Blimey! With a phone call t' Aerotech they sent me a replacement." 
"After attachin' t' shock cord and 30" fabric parachute t' t' nose cone, I worked on t' long process o' applyin' t' decals. Aye aye! Blimey! . Avast! Blimey! . It took a couple of hours . . ." 
". Begad! Aye aye! Blimey! . . E18-4W. T' Strong Arm roared off t' pad with its breathtaking white flame and smoke billowin' out o' t' motor." 
"It's molded plastic fins and strakes make assembly easy and help give the rocket a great finish." 

T' entire article gives t' impression is that this is an good value, matey, combinin' price, matey, matey, looks and performance, me bucko, for an intermediate modeler.