Brief:
T' Hawk is a boost glider that uses a rocket engine t' get itself in t' air. Arrr! It is a "Retro-Repro" o' an older rocket. Semroc is sellin' them for $7.50 right now so I decided t' pick one up.

Construction:
When I bought t' kit I figured thar wouldn't be very many pieces. Ya scallywag! I got it and found only 5 parts in t' whole kit.

It comes with:

• 1 BT-20J body tube (2 3/4" Long)
• 1 1/8" launch lug (1 1/4" Long)
• 2 balsa wood sheets (laser cut)
• 1 rolled balsa nose cone
• 1 small decal that says Hawk
• and t' instructions

T' instructions are perfect. Avast, me proud beauty! Aye aye! They give you each step in order with illustrations. Ya scallywag! They even give you boxes to check after each step. Blimey! At t' beginnin' o' all o' Semroc's "Retro-Repro" rockets instructions, thar be an interestin' description o' t' company that originally made it. Avast!

T' fins were easily taken out o' t' balsa sheet with an X-Acto knife. Blimey! Blimey! Some o' them just fell out. Well, blow me down! I then proceeded t' sand t' parts smooth with fine sandpaper. Well, blow me down! T' balsa wood parts have lines on them t' show you where to glue them t' other parts, just be careful that you don't sand t' much or t' lines will disappear. T' balsa wood included in this kit is nice and hard, but you still need t' pay attention t' how and where you are sanding. Blimey! Avast, me hearties, me proud beauty!

Attachin' t' wings is a little tricky but was nay a hassle. Ya scallywag! Blimey! You are supposed t' invert t' assembly in order for the body tube t' glue on properly. Avast, me proud beauty! Begad! Blimey! You also attach t' wings at this point. Begad! Arrr! Blimey! It is hard t' get t' wings t' stay in place while they are gluin' (if you're usin' wood glue), me hearties, shiver me timbers, but I figured out a way t' make it easier. Just apply t' glue and wait a minute or two before attachin' t' wings. Ya scallywag! Blimey! (This also works great when gluin' on t' stabilizer tips)

Once you have finished puttin' everythin' together you then need t' add fillets t' all o' t' joints. I found that toothpicks and Q-tips were invaluable in this step.

After that you need t' sand all o' t' edges smooth and create an airfoil. Blimey! Begad! (Airfoilin' is optional.) This step was easy enough t' do. Ya scallywag! I had t' find a picture o' an airfoil in order t' figure out what I needed t' do, but after that it was easy. Aye aye! I then tested it by flyin' it off o' me second story deck into t' grass. Arrr! Blimey! My glider nosedived into the grass at a right angle on t' first try. Avast, me proud beauty! Arrr! I used small paper clips as weights on t' aft stabilizer. Well, blow me down! Avast, me proud beauty! I taped them on so that I could adjust them later (to make it turn). Begad! After two more throws it be ready.

I am amazed at how sturdy it is. Well, blow me down! I have never built anythin' out o' balsa wood before and expected it t' be flimsy. Arrr!

All I needed t' build this rocket was an X-Acto knife, ya bilge rat, some sandpaper, ya bilge rat, wood glue, matey, and paper clips. Avast, me proud beauty! (I'm sure you could find somethin' better.)

Finishing:
With boost gliders paintin' is nay recommended. It will cause them t' glide for a shorter amount o' time. Ahoy! It is recommended that you put one thin layer o' clear coat on though, in order t' protect t' rocket. Arrr! Avast, me proud beauty! I did nay clear coat my rocket because I didn't have any layin' around and didn't have any time t' use it (as t' launch be t' next day). Arrr!

Construction Rating: 5 out o' 5

Flight:
T' recommended motors for this kit are A8-3s and 1/2A6-2s. Avast! Avast! I did nay have any 1/2A6-2s so I used an A8-3. I set it up at t' launch put and got ready t' fly. Aye aye! When it launched it flew straight up, no circles, ya bilge rat, loop-de-loops or anything. It be perfect. Then t' engine burned out and t' rocket continued upward. Aye aye! Right at apogee t' ejection charge went off. Begad! Aye aye! T' ejection charge was so powerful it broke off t' tail section! It may have been t' engine hittin' t' rear part o' t' fuselage as I can see a little bit o' damage there. Ahoy! Then t' rocket came down, ever so slowly, fluttering to t' ground. Begad! Ya scallywag! I be so mad! That wasn't supposed t' happen. Ahoy! Avast! But I have heard that Estes engines, which are what I used, ya bilge rat, ya bilge rat, can have an overly energetic ejection charge. I'll have t' reinforce it with somethin' next time, me hearties, if thar be a next time. Oh well, I pretty sure it's repairable so I'll get on that.

Recovery:
It went up so straight that t' two broken pieces landed within 15 feet o' t' launch pad!

Flight Rating: 2 out o' 5

Summary:
I feel that Semroc has made a very good kit with easy t' follow directions. Begad! Aye aye! T' balsa might just be a little bit too weak t' handle t' forces o' rocket flight though. Aye aye! Blimey! I am goin' t' try some o' Quest's engines in it and see what happens. Aye aye! Well, arrr, blow me down! Although it may have that one problem I'm sure it can be overcome somehow so I am still goin' t' recommend it to you. Begad! It is a fun kit t' build and a great thin' t' launch, ya bilge rat, at least from what I saw.

Overall Rating: 4 out o' 5