Brief:
This is #8 o' 10 "ready t' build" models released by Semroc at NARAM-52. Ya scallywag! T' Mini Hustler is based upon t' Lee Piester/Centuri large scale series design but downscaled t' fly on 18mm motors. Begad! This could also be considered t' little brother o' Semroc's SLS Hustler and Lil' Hustler models.

Construction:
Parts were excellent quality, and t' sealed bag contained:

• Balsa nose cone
• Series 10 slotted body tube (1" ID)
• Series 13 payload bay (tube, balsa transition)
• Series 10 booster tube
• 18mm booster motor mount (tube, matey, metal hook, me bucko, arrr, centerin' rings)
• TC-10 coupler
• Series 9 stuffer tube (1" OD)
• 18mm motor mount (tube, shiver me timbers, metal hook, me bucko, shiver me timbers, centerin' rings)
• Laser-cut balsa fins (2 sets o' 4)
• Elastic shock cord
• 12" plastic chute
• Waterslide decals

T' "ready t' build" series is Semroc's answer t' numerous requests for "ready t' fly" rockets. In t' RTB series, me bucko, t' modeler still has t' actually do work t' build and fly t' model, but t' design includes a number o' features that simplify t' build process, includin' slotted body tubes for thru-wall fin mounting, ya bilge rat, an alignment jig, arrr, and a stuffer tube t' serve as shock cord anchor and reinforce t' body tube.

T' RTB series are all fairly easy t' build, matey, me hearties, with almost all o' t' construction process usin' t' same standardized steps. Begad! Blimey! Avast! Blimey! This is definitely a skill level 1 model, and aside from paint and surface prep, t' total build is well under an hour.

T' motor mount is a standard BT-20 tube, ya bilge rat, shiver me timbers, metal hook, arrr, and a pair o' centerin' rings. Avast, me proud beauty! Blimey! Unlike t' typical mount, matey, though, me hearties, thar are two different centerin' rings involved with slightly different diameters. Pay careful attention t' t' instructions, arrr, as t' white rin' goes forward and t' brown rin' goes aft. Arrr! Begad! Blimey! This is critical later in t' process. Ya scallywag! Surprisingly, me bucko, t' mount does nay include an inner motor block, so t' metal hook will have t' hold for t' life o' t' model. I found t' centerin' rings a bit too snug, me bucko, and had t' peel off a layer o' paper from t' inside o' each, me hearties, matey, plus one layer o' paper from t' outside o' t' white ring.

T' stuffer tube contains a couple slits, me hearties, which are used t' slip t' elastic shock cord through, servin' as an anchor. After knottin' t' cord and reinforcin' with a drop o' glue, it's ready for t' motor mount. Ahoy! T' motor mount slides just a tiny bit into t' stuffer tube, shiver me timbers, enough that t' forward (white) centerin' rin' is flush with t' aft end o' t' stuffer tube. Ahoy! Do nay slide t' motor tube any further--the aft/brown rin' is too large for t' stuffer tube and instead is used t' align inside t' large series 10 body tube. Blimey! Avast! Slidin' t' assembly into t' body tube t' dry fit is a good idea at this point, shiver me timbers, t' make sure t' forward centerin' rin' is aligned properly inside t' stuffer tube. Blimey! Once t' motor mount/stuffer tube assembly has completely dried, arrr, matey, it can then be glued inside t' body tube (though be careful t' make sure t' metal engine hook does nay line up under a fin slot).

Usin' t' same two-piece fin lock technology as t' larger Hustlers, these fins need t' be bonded together first, carefully linin' up t' matchin' groove patterns. Aye aye! Begad! As noted, matey, fins are thru-wall, and t' fit against t' motor tube be very good. Included in t' kit is a nifty little cardboard fin alignment jog, matey, arrr, which fits smoothly on t' series 10 body tube and has notches t' accept 3 and 4 fin patterns. Well, arrr, blow me down! T' fixture fits well for most fins in t' RTB series, though for fins that have a significant span and are nay swept back very far, t' slots in t' jig are nay long enough t' be o' much use. Aye aye! Aye aye! That wound up nay bein' an issue on this model.

T' payload bay is a simple extension, matey, consistin' o' a 4.6" length o' body tube and a balsa transition, into which a screw eye anchor is inserted. Ya scallywag! Begad! I also drilled a couple vent holes in mine for altimeter use down t' road.

Tack on a pair o' launch lugs with standoffs , me bucko, make t' chute and construction's done.

Finishing:
I went with t' stock paint scheme on this, startin' with two coats o' primer, arrr, matey, followin' up with a couple thin coats o' gloss white, then maskin' off t' hit t' fins, me hearties, ya bilge rat, transition and nose cone gloss black, and t' payload bay gloss red.

T' waterslide decals add t' name and a roll pattern.

Construction Rating: 4 out o' 5

Flight:
T' first flight on this turned out t' be a bit o' an adventure, shiver me timbers, more me fault than that o' t' model. I loaded up a C6-5, and has intended t' load an altimeter in t' payload bay, but wound up skippin' that due t' issues with t' battery holder on me altimeter. Ahoy! As a result, t' nose cone be only secured with a light friction fit.

T' model flew perfectly straight off t' rod, me hearties, and t' -5 be t' right delay, me bucko, ya bilge rat, me bucko, deployin' just over apogee. Begad! Ahoy! Unfortunately, matey, t' elastic shock cord resulted in a snap-back effect on t' nose cone/payload, me bucko, and t' nose cone picked up one o' those common smiles/dings when it struck t' body tube. That was also enough force t' knock t' nose cone off t' bay. Arrr! I was able t' track t' tumblin' cone along with t' rocket, ya bilge rat, shiver me timbers, so I manage a full recovery.

Recovery:
Other than t' nose cone issue, shiver me timbers, t' recovery was fine. Ahoy! T' 12" chute is adequate for this weight.

Flight Rating: 4 out o' 5

Summary:
This Mini Hustler is a neat little payloader, and makes a nice addition t' t' Hustler family (SLS Hustler, Lil' Hustler).

Overall Rating: 4 out o' 5