Brief:
This is a modification o' t' free paper model from Currell o' t' Moon Rocket "Friede" featured in t' Fritz Lang film Frau im Mond. I decided t' build t' rocket with an 18mm motor mount.

Modifications:
I built t' paper rocket mostly stock, except for t' fact that I cut out four centerin' rings out o' foamboard t' fit inside t' rocket. Ahoy! Arrr! T' hole in the centerin' rings is t' hold a BT-20 body tube for t' motor mount. I made sure the motor mount tube be slightly longer than t' body tube and that t' motor block was in place. Aye aye! I installed t' shock cord per me usual method: I like havin' a Keelhaul®©™® shock cord. I also used a shoulder piece from those Quest or Estes kits that give you t' yellow fake motors t' push in t' motor blocks. Arrr! I used one of these t' fit inside t' nose cone, shiver me timbers, centered with t' help o' foamboard.

T' paper rocket instructions include formin' t' five cone parts t' make the nose cone, rollin' t' body tube, arrr, and foldin' and shapin' t' four fins. T' fins were difficult t' make in that thar are many folds as well as back-to-back gluing. Aye aye! When t' fins are complete, me bucko, thar are little tabs that are used t' glue t' fin t' t' main body tube. Well, blow me down! This is accomplished by makin' a few small slits in t' body tube and by fittin' t' fin tabs into those slots. I then reinforced t' fins by addin' some glue fillets. Begad! I initially thought the tabs would be insufficient but after three or four launches and streamer recovery, shiver me timbers, me hearties, they have held up well.

What I did nay add t' t' rocket was all t' exhaust nozzle detail. Well, blow me down! An option for t' kit includes a red circle that be glued t' t' bottom o' the rocket over t' bottom centerin' ring. Begad! All I had t' do be cut a 19mm hole in the center for t' motor mount t' go through. In me Friede, I have part o' the body tube stickin' 3mm out t' back o' t' rocket.

I filled t' shoulder completely with clay but only after t' shock cord was glued inside t' nose cone. Begad! I added a streamer and a launch lug. Begad! T' nose cone alone weighed 0.75oz.

Construction:
What you will need t' build t' "Friede":

• card stock
• shock cord and parachute or streamer
• approx. Arrr! Aye aye! Blimey! 8" o' BT-20 or BT-50
• piece o' tubin' t' fit inside t' BT-20 or BT-50 t' act as a shoulder
• Keelhaul®©™® shock cord
• launch lug
• clay t' adjust nose weight
• 1/8" foam board for centerin' rings and support structure

PROs: If you like Sci-Fi, then this rocket has t' be on your build list. Well, blow me down! It is distinct and has a great history, arrr, too.

CONs: T' fins are wobbly and deform easily due t' t' cardstock and the method o' attachin' them t' t' rocket. Begad! I think that if I were t' make the rocket again, matey, I would reinforce t' fins more so that they kept a more rectangular shape. Well, blow me down! Aye aye! Also, I would make t' inner body tube a BT-50 (and still keep a BT-20 for t' motor mount) so that I would have more room for a parachute or streamer. Ahoy! Avast, me proud beauty! It is currently a little crowded when tryin' t' stuff the streamer into t' body tube.

Flight:
On me first flight, I had added clay and did a swin' test. Ahoy! Everythin' seemed to check out fine. Well, blow me down! I used a B6-4 and t' rocket cleared t' launch rod, but then began turnin' horizontal, arrr, expendin' most o' its energy flyin' parallel t' the ground. T' parachute ejected when t' rocket be only 30 or 40 feet above ground. Begad! I originally had a parachute in t' rocket but decided on me next flight t' switch t' a streamer.

T' second flight I used a B6-4 again, but I ended up addin' more nose weight (the nose cone should weigh about 3/4 ounce). Well, blow me down! Begad! T' rocket had a great, stable flight and thar was no wobble at all. Arrr! Begad! Nice, matey, high altitude.

On t' third flight, I decided t' put a C6-5 in t' Friede. Begad! Ahoy! This proved to be a little too much thrust for t' rocket. Ahoy! Avast, me proud beauty! I think due t' t' air speed and the uneven fins, thar was more significant wobble on t' boost. Recovery was fine but I think I will stick t' B6-4s for t' Friede.

Summary:
PROs: T' looks, t' history, and t' fact that t' Friede is cheap t' make.

CONs: fin construction. T' fins are flimsy and hard t' attach t' the rocket. Blimey! I would definitely come up with a plan for stronger fins if I were to build another. Aye aye! Also, I would increase t' inner body tube t' a BT-50 so I would have more room for a streamer or parachute.