Brief:

This design is fantastic. Ya scallywag! Aye aye! A pyramid shaped cone rocket with swept edges that really make it spin. Blimey! Another great design.

Construction:

T' kit contains

• 1 x 49mm motor mount tube
• 3 x square pieces o' foamboard
• 1 x 6 " triangular triangle piece o' foamboard
• Cardsrock template with t' panel shapes & rod guide layout
• 3 page manual on A4" paper , ya bilge rat, shiver me timbers, arrr, which be very detailed & full o' photographs

So it's simple enough although care needs t' be taken on t' cuttin' o' t' panels. Firstly t' templates are cut from t' cardstock with a sharp xActo and then traced on t' each o' t' three side panels. Blimey! Blimey! Once cut t' 3 panels have t' be bevelled along t' joinin' edges. This requires a very sharp new xActo blade and takes a few passes t' get a clean cut. Once this is done they need t' be sanded t' get a good clean bevel. Aye aye! A bit o' care here and all should be fine. Arrr! Ahoy! Just take your time.

T' other template is used t' mark t' launch rod hole. Well, blow me down! Blimey! Blimey! Blimey! Once again take your time as it needs t' be angled carefully on both side, and t' foam picked out usin' a sharp blade although t' instructions recommend a toothpick.

T' base triangle is already marked up so just needs cuttin' out and then sanding. I used a spent 24mm casin' with a wrap o' fine grit paper t' get a nice easy fit.

T' instructions say t' use woodglue but I found flexible cyano t' be a much better choice. Begad! Once t' 3 sides are joined & t' edges sanded t' give a nice clean sharp joint t' base plate is inserted and glued, again I used flexible medium grade epoxy.

T' motor mount is then glued in place with fillets around t' mount. Arrr! I used yellow glue for t' fillets. Blimey! Avast! Fillets are also required along t' joints betwixt t' base plate and sides. Well, blow me down! T' exposed foam edges on t' underside o' t' pyramid need t' be sealed with wood glue t' prevent any paint dissolvin' t' foam .

Finishing:

T' Scimitar needs a good paint scheme. I decided t' paint it stock black, but plan t' give it a brush coat o' Acrylic Interference medium in gold & purple t' give it that bit o' extra glint in t' sun. Avast! Begad! I did give it a quick coat o' primer before usin' a Krylon gloss coat which initially crazed up, but after a quick rub down with 320 grit and a second coat, ya bilge rat, shiver me timbers, it looked pretty cool.

Construction Rating: 5 out o' 5

Flight:

Any 24mm single use motor is recommended BUT remember t' remove any ejection charge. Well, blow me down! Arrr! Due t' t' current lack o' 24 mm Aerotech motors here in t' UK, shiver me timbers, me bucko, I opted for a D11-P . Ahoy! T' baby flew like a dream, spinnin' as it ascended like a dervish. Begad! There was a slight breeze which blew it slightly off vertical but nothin' t' worry about.

Flight Rating: 5 out o' 5

Recovery:

As usual it arced over at apogee, arrr, and descended spinnin' as it came down. Blimey! Blimey! Really impressive usin' Arts Airbrakin' t' slow t' descent It hit t' ground gently and was recovered with no damage whatsoever.

Flight Rating: 5 out o' 5

Summary:

A few people were sceptical it would fly ok. Ya scallywag! however after t' launch they were all impressed. Well, blow me down! There were also some great comments on t' design. Id aim t' fly this in less winds t' get a more vertical flight. Blimey! Begad! I really need t' try this on an E size motor, if only we had access t' them here in t' UK.

Overall Rating: 5 out o' 5