Entry for t' EMRR Box O' parts contest - this is simple version. Well, blow me down! Avast, me proud beauty! Please link t' full documentation

Brief:
I admit t' some trepidation when I signed up for t' EMRR Box O’ Parts contest - I’m very lackin' in creative talent, bein' a mathematical sort. Arrr! Ahoy! That trepidation only grew as I read forum postings describin' the “parts” many participants were contributing. I realized that t' contest could very well be described as the “Box O’ Junk” and fervently hoped that I would get some o' t' higher quality stuff. Well, blow me down! Well, blow me down! No plastic toy soldiers or toothbrushes, please!

When me box arrived, it took me a few minutes t' build up t' courage t' open it. Takin' a deep breath, ya bilge rat, I anxiously dumped t' parts out onto t' floor and began t' sort. I was relieved t' see a good assortment o' body tubes, shock cords, matey, launch lugs, arrr, parachutes and streamers. Begad! Blimey! I was nay happy with t' balsa - small pieces o' varying thicknesses, me bucko, one o' which was junk from a die-cut fin sheet. Ahoy! Blimey! Others were broken fins... It wasn’t lookin' good! T' decals were peel and stick from an Estes Scissors Win' Transport and a water-slide sheet from an unknown plastic model. Begad! Blimey! And o' course, me bucko, I had no idea what t' do with t' plastic cup, matey, ya bilge rat, spindle, matey, Easter egg half, ya bilge rat, me hearties, and chop sticks.

I spent several days test fittin' parts, ya bilge rat, try t' come up with a design idea. I really tried t' incorporate the Easter egg half and t' spindle, but frustration rapidly set in. I could easily come up with a conventional 3 engine cluster - BT-60 adapted down t' BT-56 - but that wasn’t goin' t' attract any attention whatsoever. Avast, me proud beauty! Disgusted at my lack o' a creative spark, arrr, I put t' parts back in t' box, where they sat for quite a few weeks. Arrr!

Design

Reluctant t' give up, ya bilge rat, shiver me timbers, I pulled out t' parts once again in early June. Blimey! There was an unusually squat conical nose cone that seemed similar t' t' one atop t' Estes Mars Lander. Ahoy! Blimey! A design idea flashed into me mind - I would build a clustered rocket that looked like a lander. Ahoy! Blimey! Quickly listin' t' available parts, I set t' work in Rocksim. Begad! Ahoy! Blimey! T' design came together quickly, with t' most difficult tasks bein' t' color scheme and a name. Avast! Since I was salvagin' something out o' this box o' junk, and as I planned on usin' t' 90 from t' Estes Scissors Win' decal, me bucko, I christened me creation Salvage 90.

Simulations showed that t' recommended core engines were C11-7, shiver me timbers, D12-7, and E9-8; t' outboards contained Estes A10-PT’s. Arrr! Blimey! Salvage 90 is a high flyer - t' D12, shiver me timbers, 3 A10 combo is enough t' send t' bird t' over 1500 feet! T' long delays are necessary t' get a low speed (under 20 feet/second) at ejection.

Construction:
Parts list

• 1 Nose cone from Estes Outlander? Fits BT-60 (rounded cone, 1.25” in height)
• 1 BT-60, 10” length
• 1 BT-60, matey, 4” length (used as adapter)
• 1 BT-56, 12.625” length
• 1 BT-50, 6” length
• 3 BT-5, 7.625” length
• 1 Sheet o' 1/8” thick balsa
• 4 3.625” x 0.25” balsa strip, 3/32” thick
• 3 BT-5 t' BT-60 centerin' rings
• 2 BT-50 t' BT-56 centerin' rings (Semroc CR-913 or equivalent)
• 1 24 mm thrust ring
• 1 BT-5 coupler (hollow cardboard)
• 1 2” launch lug (3/16” diameter)
• 1 36” length o' 1/4” thick rubber (shock cord)
• 1 18” parachute (Estes PK-18)
• 1 Decal sheet from Estes Scissor Win' Transport

Construction

1) Cut all body tubes t' t' lengths specified in t' parts list (Tip: Use a coupler or empty engine case as a mandrell and wrap a strip o' card stock around t' tube t' serve as a guide).

2) Usin' a pencil, shiver me timbers, place a mark on t' Bt-50 motor tube t' denote t' bottom. Ya scallywag! Put a thin line o' glue, 3.5” from t' bottom end (2.5” if you only wish t' use C or D motors) and use a spent 24 mm motor casin' t' push t' 24 mm thrust rin' into place.

3) Place 2 marks, me hearties, one 1” from t' bottom o' t' motor tube and t' other 0.75” from t' top. Arrr! Begad! Use the wrapper in t' PDF file t' mark off 3 10 mm wide strips, matey, spaced at 120 degree intervals. Aye aye! (Tip: If you use a Windows machine, you can generate your own wrappers and alignment guides usin' t' VCP program, available at http://v-serv.com/vcp/. Avast, me proud beauty! Does much, me hearties, much more than print patterns too!)

4) Dab glue around t' motor tube at t' 2 marks made in step 3), arrr, takin' care nay t' get any in t' 10 mm strips, as t' centerin' rings will later be removed from these areas. Ya scallywag! Slide t' centerin' rings into position and set the assembly aside t' dry - thoroughly.

5) While t' motor assembly glue is drying, cut out 3 fins and t' launch lug stand-off from t' balsa sheet, makin' sure that t' balsa grain runs parallel t' t' leadin' edges. Ahoy! Use sandpaper t' make sure t' fins are t' same size, and leave t' edges square (Tip: I use copy and paste in a paint program t' print t' patterns - 1 for each fin - onto a sheet o' paper, which I then tack onto t' balsa usin' 3M Spay Mount. Begad! After t' fins have been cut out, the paper is then easily peeled off; see t' picture in t' PDF file).

6) Cut a 5 mm wide strip down t' entire length o' t' 4” BT-60 tube. Arrr! Glue this improvised coupler inside the 10” BT-60 payload tube, flush with one end. Well, blow me down!

7) Punch out t' central holes o' t' BT-5 t' BT-60 centerin' rings, and set these aside for later. Glue two of the rings together t' form a thick ring. Blimey! Well, matey, blow me down! Now use a dowel or other long object t' smear glue inside t' payload section at t' top o' t' 4” BT-60. Usin' a BT-55 or other tube, me bucko, matey, push t' thick BT-5 t' BT-60 centerin' rin' until it presses against t' end o' t' 4” coupler. Begad! This thick rin' will prevent t' ejection gas from escapin' t' payload section.

8) Cut t' BT-5 tube coupler into 3 parts, and, usin' a spent 13 mm motor casin' as a guide, glue a “thrust ring” 1.5” from t' bottom end o' each BT-5.

9) After t' glue on t' motor assembly has dried, use a hobby knife t' CAREFULLY cut away t' parts o' the centerin' rings over t' 10 mm strips. Well, blow me down! Aye aye! Then glue t' 3 BT-5 tubes into these notches, me bucko, their bottoms should be flush with t' bottom o' t' motor tube. Arrr! Blimey! Make sure t' tubes are straight and properly aligned! Allow t' dry.

10) Glue t' punched out centers o' t' BT-5 t' BT-60 centerin' rings on t' top o' t' BT-5 tubes (Note: As there were only two BT-5 t' BT-60 rings in me box, I had t' make t' 3rd from another centerin' rin' in t' box. I found t' center o' t' rin' usin' t' bisectin' segment method, ya bilge rat, and then used a circle cutter t' cut out t' right size).

11) Usin' t' PDF pattern, matey, mark 3 12 mm 7.625” inch long strips startin' at one end (the bottom) o' BT-56. Mark lines for placin' t' fins exactly midway betwixt t' strips.

12) Cut out t' strips you marked in step 11) usin' a sharp knife. Avast! I used 4 BT-60 couplers as a mandrell and a piece o' aluminum angle iron t' help get a good cut.

13) Test fit t' motor assembly by slidin' it into t' Bt-56, alignin' t' 13 mm with t' slots. Remove the assembly and place glue on t' motor tube centerin' rings and t' slot edges. Slide t' motor assembly back into the BT-56, shiver me timbers, makin' sure that t' BT-56 is firmly nested against t' centerin' rings and t' side o' t' BT-5’s. The tops o' t' BT5’s should be flush against t' tops o' t' slots.

14) Liberally fillet t' BT-5 t' BT-56 joints t' seal any cracks. Begad! Blimey! Set aside t' dry.

15) Glue t' shock cord into t' top o' t' 10” payload tube (the side opposite t' 4” coupler) using the standard Estes paper trifold mount.

16) After t' fillets have dried, me bucko, glue t' 3 fins onto t' BT-56, midway betwixt t' BT-5 tubes. Ahoy! Aye aye! Use your “calibrated eyeball” t' make sure they are vertical, matey, ya bilge rat, with a 120 degree angle betwixt t' fins. After t' glue dries, arrr, apple generous fillets.

17) Glue t' launch lug t' t' stand-off. Avast, matey, me proud beauty! Blimey! Once this has dried a bit, me hearties, matey, glue t' lug and stand-off next t' one of the BT-5 tubes, ya bilge rat, 0.5” from t' top. make sure that t' lug is vertical, and that t' rod will clear t' adjacent fin.

18) Glue t' 4 3.625”x 0.25” balsa strips evenly around t' top o' t' BT-56, ya bilge rat, ya bilge rat, matey, flush with t' top. Blimey! Make sure that t' strips are vertical and that they are at 90 degree angles with each other. At this point t' assembly looks like t' picture below:

19) Slide t' payload tube over t' balsa strips until t' top hits t' centerin' rin' at t' top o' t' coupler; the fit should be snug and thar should be about an inch betwixt t' tops o' t' Bt-5’s and t' bottom o' the payload tube. Remove t' payload tube, smear glue on t' inside o' t' coupler and, in a smooth motion, slide it over the balsa strips as before. Let dry.

20) Tie t' shock cord t' t' nose cone. Assembly is now complete.

Finishing

I applied seven coats o' AeroGloss sandin' sealer t' t' fins t' seal t' balsa and achieve that “smooth as glass” finish. Avast! T' body tube spirals were filled with thinned Elmer’s Fill N Finish, which was sanded with 240 grit sandpaper once dry. This was followed with 3 coats o' Krylon primer, sandin' with 400 grit in between, and 2 coats o' Krylon Glossy White. Begad! Aye aye! After maskin' with Tamiya maskin' tape, me hearties, t' fins and nose cone were painted with Krylon Banner Red, me bucko, and t' BT-5 outboards with Krylon Metallic Bright Silver.

I applied t' logo, number 90, and window decals from t' Scissor Win' Transport peel and stick decal sheet; the window strips have t' be trimmed t' 5.25” in length.

Flight:
July 5 was t' day, arrr, despite rain showers in t' area. I prepped t' rocket indoors, matey, ya bilge rat, loaded me duffel bag with the launch gear, and made me way through t' hot, shiver me timbers, ya bilge rat, muggy Huntsville weather t' t' field adjoinin' me apartment complex.The wind bein' out o' t' Southwest, I set up t' pad in t' SW corner t' allow for anticipated drift; I also reefed the 18” chute a bit t' speed up t' descent. T' pad was then assembled, arrr, t' launch controller wires unwound, and the battery unpacked. Well, blow me down! Begad! T' weather be still holding, so I placed t' rocket on t' pad and hooked up t' clip whip t' the ignitors.

After takin' t' obligatory pre-launch shot, matey, arrr, me hearties, I connected t' battery t' t' controller, arrr, me hearties, and checked continuity. No planes were visible, me bucko, me bucko, so I commenced t' countdown.

5...4...3...2...1...

Salvage 90 seemed t' leap off t' pad - t' combined power o' t' 3 A10’s and t' C11 got this puppy moving in a hurry! T' me great satisfaction, all 4 engines lit, matey, arrr, me bucko, resultin' in a straight-as-an-arrow flight. Aye aye! As usual, Rocksim had overestimated t' alitude performance; t' rocket fell considerably short o' t' 900+ feet that was calculated. Well, blow me down! I estimate it be more like 600-700’, no more than 700’. Aye aye! Ejection was just passed apogee, and I be relieved to see t' purple and white Estes chute open. Avast, me proud beauty! Successful on its maiden flight, arrr, Salvage 90 descended back t' Terra Firma. Arrr!

However, reefin' t' parachute turned out t' be a mistake, as t' rocket landed with one o' its fins hitting ground first, ya bilge rat, and t' combination o' weight (4 spent motors) and impact speed resulted in one fin cracking. Repairable, but it put t' kabosh on any additional flights; t' clouds were movin' in, and it seemed that t' rain would set in before t' glue could dry.

I was happy - t' design worked beautifully, and I could now submit me entry into t' Box O’ parts contest. All in all, a great day!