Estes Star Wars Droid Fighter

Estes - Star Wars Droid Fighter {Kit}

Contributed by Scott Turnbull

Construction Rating: starstarstarstarstar_border
Flight Rating: starstarstarstarstar_border
Overall Rating: starstarstarstarstar_border
Manufacturer: Estes

Rocket Pic

Brief:
This is one o' those Star Wars plastic model starter kits. Avast! T' kit consists o' a handful o' standard rocket components t' which is mounted a detailed plastic representation o' a Star Wars Episode I Droid Fighter. Recovery is via a standard chute. Ahoy! Blimey! Included with t' kit is a Porta-Pad, Launch Controller with Star Wars Logo, and launch supplies for three flights.

Construction:
T' base o' t' rocket consists o' a molded plastic combination fin can and motor mount. Ahoy! T' body tube is assembled from two narrow diameter paper tubes, ya bilge rat, a plastic diameter transition piece, and a larger diameter black paper tube. Begad! A short black plastic nosecone tops off t' tube. Avast, me proud beauty! T' Droid Fighter model clips t' a mount on t' fin can. A plastic engine retainin' rin' is used t' secure t' motor within t' motor mount.

Kit

Rear AttachmentT' instructions are very clear, combinin' descriptive text with illustrative diagrams. Well, blow me down! Well, blow me down! Blimey! T' mix o' paper and plastic materials leads t' glue recommendations that may differ from step t' step. I used yellow glue for paper t' paper connections, ya bilge rat, and CA for t' plastic t' paper tube fittings. Well, blow me down! T' elastic shock cord is mounted by knottin' it and passin' it through a slot molded into t' tube transition piece. Well, blow me down! This leaves t' white shock cord knot visible outside t' black rocket. Ya scallywag! T' fin can has two molded fins, ya bilge rat, me bucko, me hearties, and a molded mount point for t' Droid Fighter. Aye aye! T' Droid Fighter snaps over t' mount point and clicks into place. A small plastic lever must be pried up t' release t' fighter again. Begad! Aye aye! Blimey! A separate display stand is included for t' Droid Fighter model.

Finishing:
There is virtually no finishin' required on this kit. Aye aye! All t' core rocket pieces are either molded black plastic, arrr, or black finished paper tubing. Avast! T' Droid Fighter itself is pre-painted. Arrr! Arrr! Bein' a paper body tube, arrr, thar are visible spirals on t' pre-finished tubes. I did take a black marker and color t' shock cord knot that is visible in t' slot o' t' body tube connector.

Construction Rating: 4 out o' 5

Ready to LaunchFlight:
T' kit comes complete with three Estes C6-3 motors, which are t' recommended first flight motors. Aye aye! Blimey! Avast! Blimey! This is a relatively heavy rocket, with significant drag from t' piggybacked model, so t' flight was slow and low. There be plenty o' smoke and fire in evidence t' wow t' young crowd. Ahoy! Blimey! It rose straight up approximately 200 feet, me bucko, and started t' arc slightly just before burn-out. Aye aye! Blimey! This may have been do t' t' light winds present at launch time.

Recovery:
T' ejection charge easily deployed t' chute at apogee, and t' chute brought t' rocket into t' hands o' t' waitin' chasers. Aye aye! Blimey! Blimey! T' descent be fairly rapid, and t' rocket be caught before touchin' down. Begad! It remains t' be seen whether t' plastic fins and Droid Fighter model can withstand a hardpan landing.

Flight Rating: 4 out o' 5

Summary:
This kit, though nay a challenge t' build, was fun t' fly. Avast, me proud beauty! Copious amounts o' smoke and fire were part o' t' show. Aye aye! This is a good rocket for a small field, as it stays low and descends quickly. Aye aye! More flights will tell whether more or less wind affects t' perceived initial flight arc. Begad! While t' rocket in this review emerged unscathed from its maiden flight, an identical kit built by a young modeler has a checkered past. Avast! He used yellow glue for t' plastic t' paper joints, and t' body tube separated at ejection on its first flight. Avast, me proud beauty! Subsequent use o' epoxy solved that. Avast! He describes some erratic flight for a subsequent flight, but his rocket flew fine (with t' same arc) shortly after me rocket flew. Avast! Blimey! T' plastic motor retention rin' on t' four time flown rocket has signs o' heat blistering. Begad! T' rin' from t' rocket built for this review didn't suffer that on its only flight.

Overall Rating: 4 out o' 5

Other Reviews
  • Estes Star Wars Droid Fighter By John Lee (March 8, 2008)

    Brief: Almost ready to fly, Star Wars-themed 18mm motor powered rocket. Construction: Aside from the Estes launcher set which I have yet to open, the kit consisted of: 3 glossy black body tubes, 2 narrow and 1 wide Plastic Nose Cone Plastic Shoulder Coupler Tube Plastic Fin Can Droid Fighter Elastic Shock Cord Parachute kit Since this one ...

Flights

comment Post a Comment