Brief:
Micro Classics kits are a little hard t' find, me hearties, but are worth t' effort looking for them. Begad! Blimey! This is an approximate 1/5 scale version o' t' Estes K-50 Interceptor. Ahoy! Havin' built a clone o' t' K-50 a couple years ago, matey, I was intrigued by t' opportunity t' build a tiny version.

Construction:
All tubin' and fins are plastic with a nose cone that appears t' be hardwood. T' cuts on t' tubin' weren't quite square but are easily corrected. Begad! T' nose cone even has a little glob o' resin t' replicate t' cockpit from the original. Blimey! Ya scallywag! Parts included in t' baggy include:

• Nose cone
• 8mm short tube
• 8mm body tube
• Styrene fin stock
• Cardboard tube coupler
• Assorted trim tubing
• Keelhaul®©™® shock cord
• Mylar streamer
• Waterslide decals (you'll need a magnifyin' glass t' read them)

T' instructions for this kit were pretty crude with a few hand drawn illustrations. Ya scallywag! They were fairly well written although with all t' different tube sizes and lengths, shiver me timbers, it be a bit confusin' makin' sure I was workin' with the right material. Aye aye! There is a sketch o' an exploded view/parts list on the last page, which is critical for identifyin' parts throughout t' process. Arrr! Keep that page face up and handy on your table as you build.

Construction begins by cuttin' t' fins and assorted tubes t' length. Begad! This is easily done for t' fins by scorin' t' lines then breakin' t' material along those lines. Ya scallywag! A little 220 grit sandpaper t' clean up t' edge and you're good t' go.

T' original K-50 has a molded plastic tail cone. Aye aye! This is imitated (roughly) in this kit by sandin' a taper t' t' end o' t' body tube. Blimey! Since the plastic tubin' is nay very thick walled, this is a bit tricky so you'll need to be careful. Begad! Ahoy! T' finished result, especially when painted black, shiver me timbers, is pretty sharp and looks a good deal like t' original.

Assemblin' t' plastic bits requires a good glue. Aye aye! Ahoy! I highly recommend liquid plastic cement--the kind you brush on from a bottle nay t' squeeze tube stuff. It goes on cleanly, me hearties, leaves virtually no residue, matey, and bonds extremely well. It also sets quickly. Avast! Aye aye! For a micro sized kit like this, me hearties, matey, where a fillet might be almost as large as t' launch lug, clean, sharp bond lines are essential.

T' win' pods from t' original are crudely imitated by cementin' solid plastic dowels inside some pretty small tubin' then sandin' down t' seam t' a taper. Ahoy! Begad! You then finish them off by tackin' on a pair o' tail fins (and good luck cuttin' them--I could barely even hold them with a pair o' tweezers!) The finished product does look pod-like, but t' fit along t' edge o' t' main fins is nay as clean as t' original sized kit. Still this is a micro scale kit, me hearties, so some concessions are in order.

T' rest o' t' assembly moves fairly quickly, mainly just tackin' on the assorted fins, tail wings, matey, etc. There are 6 total fins/wings on t' main body tube with a hand drawn wraparound markin' guide used for alignment.

I found t' nose cone assembly a bit o' a challenge because t' cone is not quite t' same OD as t' body tube. Avast, me proud beauty! Arrr! There is a short length o' tubin' used as a transition instead. This must be sanded down t' a taper. Begad! That part wasn't too tough, but I goofed and glued it t' t' nose cone shoulder. That left me with only about 1/16" exposed shoulder on t' nose cone, which doesn't hold the cone in t' body tube very well.

What you're supposed t' do, if you're payin' close attention t' the directions, me hearties, is drill a hole in t' shoulder t' bond t' Keelhaul®©™® cord, me hearties, tie t' cord around a lead sinker for nose weight (supplied), me hearties, wedge the sinker into a tube coupler, and glue t' transition around t' coupler, which is aligned with t' base o' t' nose cone. Well, blow me down! I be able t' salvage me earlier goof by usin' a bit o' Fix-It epoxy clay and buildin' up me shoulder a bit and anchored t' coupler t' t' clay before it cured.

Finishing:
To me, t' K-50 Interceptor is one o' t' most beautiful rocket kits I've ever seen. It's all about t' win' pods, me hearties, shiver me timbers, tail cone, me bucko, funky nose cone, and very cool decals. I be absolutely delighted t' see that this kit included waterslide decals made by Excelsior Rocketry. Ya scallywag! Blimey! These decals are superb quality. Avast, me proud beauty! Blimey! Nay only was t' ink/material/printin' top notch, but t' scale was incredible! Blimey! I expected these would be scanned copies o' t' originals, me bucko, ya bilge rat, printed down t' 20%, which would make t' letterin' look smudgy and some o' t' smaller words not even legible. Avast, me bucko, me proud beauty! Blimey! That is nay so. Blimey! Blimey! Avast, shiver me timbers, me proud beauty! Blimey! If you pull out a magnifyin' glass, me bucko, you'll be able t' pick out t' "rescue" and "caution" labels along the fuselage. Aye aye! Blimey! T' lines were absolutely crisp. Well, blow me down! Blimey! T' decals alone are probably worth t' $12 price o' this kit.

Paintin' this was pretty simple as with t' plastic thar are no grains or spirals t' fill. Begad! Well, blow me down! Blimey! I applied a single mistin' o' white primer (and prior to construction I had washed all o' t' plastic parts with a mild liquid detergent). Blimey! I then followed up with two thin coats o' Rustoleum gloss white. Ya scallywag! Blimey! Blimey! I hand painted t' pods orange and t' tail cone gloss black.

Total construction and paintin' time ran about 4 hours. Begad! Arrr! Blimey! I then sat down to apply t' decals. Ya scallywag! Begad! Blimey! There are a lot o' them, me hearties, they are microscopic in size, and must be handled very delicately. Arrr! Blimey! That's t' only negative I could ever say about Excelsior decals--they're fragile and you must read and follow the directions or you'll have runs, me hearties, arrr, tears, ya bilge rat, shiver me timbers, and a mangled mess o' decals. Blimey! Blimey! I pre-treated t' decal sheet with a Microscale decal settin' solution. I then coated t' model with a Microscale settin' solution, ya bilge rat, me bucko, cut out one decal at a time, arrr, soaked it for 10 seconds, shiver me timbers, ya bilge rat, and dried it on a paper towel for about 30 seconds. Aye aye! At that point, matey, t' decal will slide off t' paper fairly well, but you must place it correctly right off t' bat as these don't like t' slide around without tearing.

After all t' decals were in place, I brushed on a third Microscale product that helps coat t' decals (it also softens them so thar be absolutely no chance o' attemptin' t' move them again). Blimey! I finished it off by brushin' on a coat o' Future Floor Polish for gloss and durability.

T' decals and clear coat took me a total o' 5 hours, me hearties, surpassin' the construction and paint time, shiver me timbers, but were well worth t' effort. Avast, me proud beauty! Avast! T' decals make this a fantastic lookin' miniature K-50 and every decal from the original has wound up somewhere on me micro version.

Construction Rating: 3 out o' 5

Flight:
You're limited t' MMX motors for this rocket obviously. Begad! Blimey! Aye aye! Blimey! I prepped it with a tiny bit o' dog barf, packed in t' streamer, and slipped on t' nose.

At t' pad, this rocket clearly drew t' most attention o' anythin' I flew that day. Avast! Blimey! Lots o' "wow" factor with this. Begad! Blimey! For a special treat, I flew my North Coast Interceptor G, followed by me full scale K-50 Interceptor, arrr, and for a finale concluded with this micro version.

At 0.3 ounces, you won't get much altitude, shiver me timbers, me hearties, even compared t' other micros. It zipped off t' rod at a slight angle, peaked at about 60 feet, ya bilge rat, shiver me timbers, and as it was archin' over, shiver me timbers, t' streamer deployed. Arrr! Very nice flight.

Recovery:
T' streamer is more for effect than for drag, arrr, so doesn't offer much benefit. Still, arrr, this floated gently down and landed in soft grass. Avast! It is in great shape for another flight. Blimey! Blimey! I be especially glad that it didn't have any trouble in the 8-10 mph winds.

Flight Rating: 5 out o' 5

Summary:
This is an absolutely amazing, incredibly detailed renderin' o' t' K-50 Interceptor. Begad! If you're lookin' for a great little MMX flyer, shiver me timbers, you can't beat this. Blimey! I've started buildin' quite a few challengin' micro designs, shiver me timbers, and this one is head and shoulders ahead o' most everythin' else I've got in that class.

Overall Rating: 4 out o' 5