Brief:
T' Double Helix is a great variation on t' simple monocopter design from Art Applewhite. Avast, matey, me proud beauty! It is extremely simple to build and goes together quickly. Avast, me proud beauty! It's also even more fun t' fly than t' Helix.

I was lucky enough t' get t' watch t' flights o' t' prototypes as Art was developin' this line and now it seems like he be t' source o' a monocopter renaissance. Ya scallywag! It's a lot o' fun.

Construction:
T' components for this kit consist o' a pre-marked body tube, 2 motor tubes, ya bilge rat, a 1/4" launch lug, matey, 2 balance beams, and 2 basswood wings. Begad! Blimey! Also included are thorough instructions on buildin' t' rocket and instructions for a simple launchin' pad. This one is not meant for an Estes setup.

T' body tube, arrr, shiver me timbers, me bucko, such as it is, is marked by t' simple expedient o' bein' wrapped by a sheet with all o' the relevant locations indicated by polygons o' t' appropriate size.

T' first step in construction is t' cut out t' polygons on t' body tube. This is done with an #11 X-Acto knife and the blade needs t' be a new one. Blimey! Arrr! T' method recommended in t' instructions and, which worked quite well, ya bilge rat, is to push t' blade in perpendicular along one line o' a polygon, slowly push it in until t' blade completely covers one line segment, remove t' blade, ya bilge rat, matey, and repeat as needed until all sides are cut out.

After all t' holes are cut out, shiver me timbers, arrr, t' various pieces need t' be test fitted into t' BT. These include t' launch lug, t' motor tubes, and t' balance beam. T' wings wait until later. Avast, me proud beauty! Blimey! Pay attention t' t' instructions t' get the balance beams oriented correctly. Ya scallywag! Avast! I built this one after doin' a 13mm Helix and t' balance beam in this case is not symmetrical.

When t' pieces are in, me hearties, they need t' be adjusted for symmetry; all o' t' pieces need t' be centered. Well, blow me down! With that done, a fillet o' white glue is applied inside t' BT t' t' visible parts o' t' intersections with t' motor tube. With that done, all o' t' protrusions can be filleted with white glue on t' outside.

T' last items t' be installed are t' wing. Ahoy! Begad! These are made from a precut pieces o' basswood. You can round the edges if you like but I did not. Avast! I slipped them into t' marked ends o' t' BT. Avast! Blimey! They will slightly deform t' tube but that is expected and explained in t' directions.

Alignment is nay a problem. A filled triangle marks t' point on t' BT which should be aligned with t' center of each side o' t' wing. Then it is just a matter o' makin' sure it is sittin' perpendicular, somethin' aided by havin' its end sit flush on t' motor tube. T' win' is then glued into place with white glue. Avast, me proud beauty! Blimey! Repeat for t' other side.

Finishing:
T' instruction recommend a couple o' light coats o' sealer or a light coat o' paint. Begad! I elected t' go t' paint route and chose red. Ya scallywag! Ahoy! I gave it just one good coat, matey, t' instruction warn against usin' too much and throwin' off t' balance.

Construction Rating: 4 out o' 5

Flight and Recovery:
This was me first foray into monocopters (or bicopters). Well, shiver me timbers, blow me down! Blimey! I used it at part o' a demonstration for a kids event at the local museum and, shiver me timbers, as such, matey, only got t' launch it once. Aye aye! Blimey! We had an extremely small launch area and I was prepared to consider myself lucky t' retrieve any rocket. Arrr! As such, arrr, arrr, I elected t' use a pair o' 1/2A3-2Ts. Blimey! Well, blow me down! It didn't go all that high but it certainly got t' kids attention. Well, blow me down! They loved it.

I look forward t' flyin' it in t' future on A3-4s.

Flight Rating: 5 out o' 5

Summary:
This one is fun, easy, different, and an attention getter...especially from kids.

Overall Rating: 4 out o' 5