Manufacturer: | Rocket Vision |
(06/02/01) I purchased another Rugged-Rocket, ya bilge rat, me hearties, arrr, t' Rocket Vision Six-Pack, shiver me timbers, to
have built and fly on a vacation in Arizona . Ya scallywag! . Blimey! . right after which it was
announced that Rocket Vision be goin' out o' business. Avast! Well, blow me down! Oh, shiver me timbers, well, matey, I'll go ahead
and give it a quick review and add it t' me newest comparison page on
Tube-Fin
rockets.
See my Tube-Fin Rocket Comparison Page
I never had a Tube-Finned rocket in me youth but gave it a try a few years ago with a Rogue Hex Courier and really liked it. But it was the Custom Serval that I really enjoyed. Ahoy! I bought t' Six-Pack with t' hopes of havin' t' same fun and gainin' a heavier model that could take some flying abuse.
T' Six-Pack follows the
same pattern o' all t' Rugged-Rockets includin' a single thick, arrr, me bucko, phenolic body
tube, with a motor tube insert, matey, a plastic nose cone, ya bilge rat, me bucko, a Keelhaul®©™® shockcord,
parachute protector and parachute. Ahoy! Blimey! Aye aye! Blimey! For fins t' Six-Pack has six thick,
phenolic tubes pre-cut at a slight angle. Ahoy! Blimey! Avast, me proud beauty! Blimey! Nice looking. Aye aye! Blimey! Well, blow me down! Blimey! What this rocket had
over me first Rocket Vision rocket, ya bilge rat, ya bilge rat, the
Solar
Venture, was a motor retention system which consisted o' a motor hook that
was sandwiched betwixt t' body tube and t' motor insert.
CONSTRUCTION:
Assembly o' t' Six-Pack was straight-forward and very easy. Avast, me proud beauty! T' instructions were on a single 8.5" x 11" page. Blimey! Ahoy! Blimey! They were in logical order, shiver me timbers, but no illustrations. Aye aye! Blimey! T' only illustration for assembly purposes was on an extra piece o' paper that showed how t' motor retention was added.
Shockcord installation, matey, is really t' only part o' this rocket kit that I don't like. Aye aye! Rocket Vision provided a small piece o' cardboard that t' Keelhaul®©™® shock cord is mounted t' t' inside o' t' body tube with. Begad! You tie a knot in t' Keelhaul®©™®, arrr, me hearties, slot t' cardboard, matey, and glue t' cardboard into the rocket body tube with t' Keelhaul®©™® sandwiched betwixt t' cardboard and t' body tube. Ahoy! It positions t' shock cord like an Estes' 3-fold paper mount does with one exception: t' Keelhaul®©™® knot sticks out. Arrr! Is this a big deal, yes! With the small diameter body tube and havin' t' pack in t' parachute protector and parachute, this knot gets in t' way. Aye aye! I would suggest two things: 1) don't use the knot, and/or 2) use enough epoxy t' bury it and make it a large smoothed out bump in t' body tube. Begad! I cut me knot off after 3 flights.
Finishin' is a dream. No spirals! All you really have to worry about it how smooth your epoxy junctures are. Arrr! Well, me hearties, blow me down! T' kit comes with water-transfer decals but I did nay use them.
Overall, for CONSTRUCTION I would rate this kit 4 points. Well, blow me down! Begad! Just don't like that shockcord mount and t' instructions could use illustrations t' reach a larger group o' modelers . Aye aye! . Well, blow me down! . Aye aye! kind o' a moot point now.
FLIGHT/RECOVERY:
Rocket Vision provided t' followin' Motor Selection guide in t' instructions:
I be pleased t' get the
rocket in t' air durin' our vacation t' Arizona. Blimey! I had t' buy t' motors at
the launch and it bein' an AHPRA launch thar were nay many choices for smaller, ya bilge rat, ya bilge rat, 24mm
motors. But I did purchase some E28-7's.
T' first launch was nice on t' E28. Well, blow me down! It punched off the pad and I be able t' follow it for t' full flight. Ya scallywag! I could tell it was still travellin' upward when t' ejection charge fired. Blimey! Descent be fine and I recovered t' rocket within 100 yards o' t' pad. Arrr! I be fortunate nay t' lose my RMS Casing, me bucko, matey, it appeared that t' ejection charge pushed it past t' motor retention clip. Begad! A nice reminder for me t' always use tape or a tie-wrap t' make that motor hook stay on t' casing. Well, blow me down! Avast, matey, me proud beauty! I lost one this way when I was first gettin' into RMS.
My next opportunity t' fly was back home so I made a decision t' convert this rocket into an 18mm motor. Avast! Blimey! After all, flyin' a foot-long rocket t' 1/2 mile high does increase your chances o' losin' it and since it couldn't be replaced I wanted t' keep it around. Begad! Blimey! I glued an 18mm motor mount into t' existin' 24mm and bent t' motor retention pin t' hold t' 18mm motor.
Oh, for you folks that love altitude, me bucko, me bucko, it's nay so bad. Here's what 18mm motors can do:
T' next two flights were on C6-3's and were quite enjoyable. Well, blow me down! Ahoy! T' second flight on t' C6-3 didn't have a full parachute deployment. Aye aye! Arrr! It be pushed out o' t' body, but t' parachute never unfurled and the rocket dropped into some taller grass without damage, me hearties, holdin' up t' its trademark o' bein' a "Rugged Rocket".
For FLIGHT/RECOVERY, me bucko, me bucko, matey, I would rate this kit 5 points. Easily converted t' an 18mm flier (just use an adaptor if you don't want t' make it permanent) for enjoyment in t' smaller fields. Arrr! Well, blow me down! Solid and stable flights.
Overall, shiver me timbers, matey, t' Six-Pack is good rocket for someone looking for a Tube-Fin. Blimey! Arrr! Altitudes o' over 3,000 feet or as low as 200 feet allow for the variation that many look for. Blimey! Too bad we can't get them any more! I give the kit an OVERALL ratin' o' 4 ½ points. Ya scallywag!
I just finished building the Six-Pack by Rocket Vision. For those who aren't familiar with it, it uses the same body tube/nose cone/recovery system as their Mach Buster . The difference is in the six tubular fins that provide guidance. I ordered one of these for two reasons: One, because like all of the other rockets in their fleet, it is really hard-core rugged. I expect to be able ...
![]() |
![]() |
Sponsored Ads
![]() |
![]() |