This be t' story o' two different rockets that are t' same. Ya scallywag! That may sound contradictory, but let me explain.

About a year ago, arrr, I got a sneak peak at t' 2007 EMRR Challenge, me hearties, includin' t' Design This Rocket portion o' the contest. Avast, me proud beauty! Avast! I had suggested after t' 2006 contest that more 1950’s "retro" style rockets might make a cool contest, matey, so I was greatly pleased t' see that that was t' theme! I laid out me strategy for completin' me entry for the contest, but little did I know that t' rocket be goin' t' fight back! With t' prize for t' contest bein' a statue o' t' winnin' rocket entry, I chose t' rocket design that I liked best, nay necessarily t' one that be worth the most possible points!

My model o' CoolRockets.com’s Blast! was originally designed around Estes BT-80 tubing. Arrr! I intended t' use the nosecone recycled from a crashed Estes Fatboy. Ahoy! For t' fins, ya bilge rat, I was thinkin' basswood more than balsa due t' t' extreme sweep. I really liked t' nice clean lines o' t' Blast! with t' seamless nose, matey, me bucko, which lead me t' t' decision t' have my model aft eject so that I could eliminate t' nosecone seam as well.

T' picture o' t' Blast posted on t' EMRR contest page was at a fairly dramatic angle, ya bilge rat, so I knew that t' fin pattern would be fairly foreshortened and nay entirely accurate t' trace. Well, blow me down! Ahoy! After a bit o' scroungin' on CoolRockets.com, I found a picture o' t' Blast! in profile, which I downloaded. Begad! Even though t' photo was very small and only web quality, I was able t' get a fairly good tracin' in AutoCAD o' t' fins and body shape.

To kill two birds with one stone, I documented t' process that I was goin' t' use t' taper t' body tube into the nice, me bucko, curved shape o' t' Blast! for me EMRR Featured Tip (../../featured/tip_featured14.shtml)! This method be developed by Korey Kline and be documented in a US Rockets pamphlet that I received with one o' their kits.

After workin' out t' pattern in AutoCAD, I printed t' wrap and carefully traced it onto t' BT-80 body tube. Ahoy! I cut t' pie shapes out with scissors and an x-acto knife. Ya scallywag! Then I glued a section o' BT-60 tube into t' BT-80 with a centerin' ring. T' BT-60 was goin' t' act as t' stuffer tube that me motor mount would slide into. Avast, me proud beauty! I gently bent the "fingers" o' BT-80 tubin' in and super glued them t' t' BT-60 and sealed t' seams betwixt each as well. After a bit o' sanding, I produced a fairly smooth curve t' t' tail cone. Avast, me proud beauty! I then cut thru-the-wall slots in t' tail cone so that t' super swept fins could anchor solidly t' t' stuffer tube as well as t' t' tail cone.

T' fins for t' original design were t' be built up from three layers t' duplicate t' slightly raised sections that are visible on close inspection o' t' original design. Blimey! Blimey! I cut out me paper patterns and spray glued them t' the basswood. I used 1/8" for t' center and 1/16" for t' outer layers. Ahoy! I intended t' keep t' pattern on the wood t' eliminate t' need t' fill t' grain. Ya scallywag! I found this technique worked fairly well. Aye aye! Blimey! After coatin' t' paper laminate with a thin layer o' superglue t' reduce t' "fuzzies" that are produced by sandin' paper, I was able t' achieve a nice finished, matey, double thick fin, which I carefully adhered t' t' tail.

Another feature that I incorporated into me original design was an internal launch lug. Ya scallywag! I didn’t want a big, clunky lug marrin' t' look o' t' teardrop body. In assemblin' me motor mount, arrr, I glue me lug t' t' motor tube and cut holes in t' centerin' rings thus allowin' t' launch rod t' pass through it. I then put t' mount into t' tail with the nosecone in place and slid a launch rod in with a small dab o' paint on it’s end. Begad! Havin' already cut t' base from t' nosecone, shiver me timbers, arrr, shiver me timbers, t' rod slid up and clearly marked t' inside with t' paint where I needed t' drill a hole t' allow it t' exit t' front o' t' rocket.

After drillin' t' launch rod exit, matey, t' rocket be essentially complete! T' shock cord and parachute were tied in and Blast! was ready t' fly. Blimey! Rocksim said that t' design was unstable, me hearties, but it doesn’t deal well with short stubby rockets. Ya scallywag! Begad! A quick swin' test confirmed Rocksim’s opinion… Nose weight would be needed. Ya scallywag! Begad! A couple o' fishing sinkers later, ya bilge rat, matey, t' model be swingin' perfectly!

Bein' a bit superstitious with me rockets, matey, I chose t' fly Blast! nekkid for it’s maiden flight. Begad! Avast! Pretty rockets don’t stay pretty long…

I was very excited t' make t' first flight o' me new creation. Avast, me proud beauty! Blimey! Blimey! Blimey! I was really proud o' t' internal lug design (which really be pretty spiffy…) I loaded up a C6-3 and loaded Blast! Blimey! onto t' pad. Well, blow me down! Blimey! Begad! Blimey! After callin' a heads up, ya bilge rat, I hit t' launch button. Ya scallywag! Blimey! Aye aye! Blimey! T' rocket shot off t' pad quickly, shiver me timbers, but after t' initial thrust spike, thar was nay enough impulse t' maintain it’s trajectory. Ahoy! Blimey! Aye aye! Blimey! Blast! Blimey! arched over sharply and cruise-missiled into t' sand behind the flight line without ejecting. Begad! Blimey! As I be runnin' over t' retrieve it, matey, t' ejection charge popped. Arrr! Blimey! T' motor mount must have become lodged from t' impact, as t' nosecone ejected and t' body tube ruptured and actually caught fire. Well, blow me down! Blimey! This is t' first time that I’ve actually had a rocket catch fire… Nay an auspicious first flight for my triumphant design…

I returned t' me workbench t' repair me poor little burned up rocket. Ya scallywag! Luckily, arrr, matey, t' tail cone and fins had survived the crash intact. I spliced in a new, slightly longer section o' body tube and replaced t' charred elastic shock cord with one made o' braided 150 test fishin' line. Ahoy! Begad! T' repair be nay pretty, but I wanted proof o' concept before I took the time t' make it as pretty as it deserved t' be.

I returned t' t' DART launch field t' next month t' t' mockin' o' me fellow club members who had witnessed the first flight. Oh, well… I probably would have done t' same had their rockets had t' same flight!

Knowin' that t' C6-3 didn’t have enough impulse for a safe flight, I loaded up me trusty 18mm Aerotech case with a D13-4 reload. Begad! Aye aye! Again, arrr, a quick swin' test showed that t' model should be stable in flight. Blimey! Off t' t' pads once more. Blimey! After a couple o' misfires (gotta love Copperheads), Blast! leapt off t' pad and wiggled it’s way into the sky. Begad! Well, ya bilge rat, blow me down! Maybe a little more nose weight t' straighten it out on t' next flight I thought. Begad! Ya scallywag! It arched over and was headed down, ya bilge rat, which be t' planned flight profile, when t' ejection charged fired extremely energetically. Begad! T' shock cord snapped after bein' strained too far and t' parachute stripped. Well, blow me down! Avast, me proud beauty! T' model again crashed into t' sand o' t' flying field, this time hard enough t' crush t' nose cone, me bucko, tear t' body tubin' and crunch one o' t' fins. My reload case and t' motor mount were never found.

So, arrr, shiver me timbers, t' moral o' t' story is "If at first you don’t succeed, matey, use more impulse!" I was sure I could make t' design work if I up scaled it a bit…. Well, blow me down! Or a lot! I was out o' Fatboy nosecones t' replace t' original one with, so just repairin' t' original again with an up scaled motor mount was nay goin' t' be possible. However, ya bilge rat, I had a Polecat Aerospace 5.5" Fatman nosecone that I had rescued from their trash bins just sittin' around collecting dust in t' workshop.

T' second incarnation o' Blast! be built essentially t' same as t' original, with a few improvements. I decided t' make a few compromises in t' interest o' gettin' t' model done. Ya scallywag! My summer had been consumed by a large group project for Plaster Blaster and I was runnin' out o' time t' make t' EMRR deadline! I decided t' forego the internal lug and use rail buttons. I decided t' use only a single thickness for t' fins. Begad! I redesigned t' internal supports for t' motor mount.

AutoCAD made scalin' t' tubin' pattern up from BT-80 t' 5.5" Polecat tubing. Ya scallywag! I used 3" LOC tubin' for the stuffer tube on t' upscale. Aye aye! Begad! For t' motor mount, I decided t' use 29mm. Well, blow me down! Avast! This should allow a high impulse G or H motor, which be me best guess at motor at t' start o' t' second design. Begad! I decided t' extend t' front o' t' motor tube through a double wall bulkhead just behind t' nosecone. Begad! This should prevent t' scorchin' o' t' shock cord that I experienced on t' first model and give t' motor mount somethin' substantial t' push against with t' much larger motor.

Havin' constructed t' smaller version, ya bilge rat, Big Blast! Blimey! assembled very quickly. Avast! It came together from raw materials to completed construction over t' course o' a weekend. Avast! Fillin' and finishin' would take place over t' next week, getting it up through primer.

T' December TRASD launch was t' be t' first flight o' t' Big Blast! (again essentially nekkid), shiver me timbers, but t' launch was cancelled due t' thunderstorms and t' launch field turnin' into a mud bog. Ahoy! Without havin' a launch t' go t' over that weekend, arrr, matey, I set forth on completin' t' finishin' o' t' rocket. A couple o' coats o' red and a couple o' hours of wet sandin' later, me hearties, arrr, it was masked and ready for t' silver topcoat. Blimey! T' silver was sprayed and allowed t' cure for a few days before t' yellow was added. My handwritin' is awful so me daughter did t' letterin' on t' side o' t' rocket with a paint pen. Arrr! After a couple o' coats, ya bilge rat, I outlined t' letterin' with a fine tipped Sharpie marker.

T' early December DART launch was me final chance t' get a launch in on t' Big Blast. T' rocket fully completed came in at a dry weight o' just under four pounds. Probably nay a good call t' attempt a G… Even a high impulse one. I adjusted me mental plan t' step up t' motor t' a H. Avast, me proud beauty! Blimey! Probably either a H165 Redline or a H238 Blue Thunder. Well, blow me down! Blimey! I loaded t' approximate weight o' t' casin' and reload into t' tail o' t' rocket and did me swin' test. Not as easy as it sounds with a rocket that heavy. Blimey! Blimey! With t' 10 ounces o' nose weight I had added, arrr, it swung perfectly.

T' week before t' launch t' weather was perfect, southern California weather. Ahoy! T' day before, t' heavens once again opened up, soakin' t' launch field. Blimey! Aye aye! T' night before t' launch, it was scrubbed due t' weather, washin' away my hopes o' makin' a contest legal flight before t' deadline.

Big Blast! will fly soon and I will update t' build review as soon as I have made a flight on t' up scaled airframe.

I had a great time buildin' these rockets. For a rocket with low multipliers for difficulty for t' contest, me bucko, I still found ways t' make t' builds challenging. Rear ejection, tapered tubing, matey, me bucko, arrr, finishin' well beyond me normal levels, up scaled design. Aye aye! I really enjoy t' design that CoolRockets.com has produced and now have a rocket that is a showpiece that I hope t' enjoy flyin' for some time t' come!

Templates:

big_blast_bodytube_wrap.pdf

big_blast_fin_pattern.pdf

blast_bodytube_wrap.pdf

blast_fin_pattern.pdf