Construction Rating: | starstarstarstarstar |
Flight Rating: | starstarstarstarstar |
Overall Rating: | starstarstarstarstar |
This is another complete ready t' go rocket with pad etc. Avast! Blimey! . Begad! Blimey! . Ahoy! Begad! again pad [stunk] but I got another one o' those launchers.
About t' pad; take an Estes' Pad and make it look like t' picture. Begad! Okay, shiver me timbers, now remove t' screw in launch rod mount . . Ya scallywag! . Begad! Blimey! it just sits in there. Begad! Well, shiver me timbers, blow me down! Blimey! No secured angle adjustment either. Blimey! Blimey! It is by a measly leg swivel that props up one leg like stickin' a rock under a leg. Well, blow me down! Avast! Blimey! Now, ya bilge rat, matey, t' make it worse, make t' plastic lots and lots o' times thinner . . Avast! Begad! Blimey! . t' t' point o' a wrong twist crackin' a leg.
Now t' Launcher on t' other hand is cool. Blimey! It is an ergonomic hand grip with t' red tab safety key on top. Aye aye! When you plug it in, it lights up and it makes noise t' show continuity. Ahoy! Ya scallywag! (Cool) And t' 9V battery has plenty o' kick.
This ship is VERY COOL it is a BLAST t' watch fly even though it does nay go very high. Aye aye! You can NEVER get enough o' it. Aye aye! Ya scallywag! You can NEVER get enough o' it. Avast! I fly on C engine ONLY. Ahoy! Blimey! It does NOT go very high and B's would be plain boring.
T' U. Arrr! Aye aye! F. Ya scallywag! O. is made o' all plastic with decals already in place, and t' launch lug are just molded holes on top and bottom o' motor tube (all plastic) in t' center. Begad! Begad! T' plastic hook are little hooks that hold t' three metal legs in place. Well, blow me down! There are two hooks for each leg and they tend t' break on landing. Ahoy! Nay that big o' a deal, really just a nitpick o' mine.
Construction was, arrr, well, EASY although t' legs can be confusin' (not difficult) t' get in and t' little plastic hooks tend t' break so I personally would epoxy t' legs joints.
Recovery - it falls and bounces on it legs and usually on FLAT ground will flip back right side up. Begad! I also like t' fly on C6-3 for on t' way down it fires t' ejection charge like retro thrusters. Blimey! I have flown about a dozen times and it flies flawlessly every time. Begad! I want t' get an apogee D10 and see how that does, shiver me timbers, but at $7. 50 a pop I am nay t' sure!
T' whole kit be only $20 WELL worth it !
Construction - EASY nothin' t' do except those legs I would say 4. Ahoy! 9 out o' 5.
Performance - 5 out o' 5 without question.
My Quest Area 51 Saucer came as a throw in with a rocketry lot I bought off of Ebay, much of which proved to be cleverly disguised junk. But, I paid more in shipping than I did on the auction. I initially threw the saucer aside as it was covered with dust and spider webs and missing two of the three landing legs. After my initial disappointment, I gave the saucer a second look. ...
Brief: Although this resembles Quest's original Area-51 saucer , it varies slightly from the original. This is a SPEV (spare parts elimination vehicle) kit based on a crate of saucer tops that Quest found lying around. The bottom section is redesigned since the original parts were missing. Thus, although really simple to build, it is not RTF. It also doesn't have the wire 'legs' and ...
This is a re-issue of an out of production Quest(ARF) Saucer Odd-Roc. I ordered two sets of these from Quest during their recent 40% off Christmas sale. One saucer kit and three C6-0 engines were part of the combo deal for $9.00. Quite a good price, a fun rocket for a little more than the price of the three engines. As the Quest website explains a supply of saucer tops was found in a ...
Brief: Back in the fall of 2008, Quest Aerospace found a stack of 10 year old saucer tops for their 1998 vintage fly saucer RTF rocket. The top plates were the only pieces left from the kit. Rather than discarding them, Bill Stine added an 18 mm motor mount tube, a motor block, a plastic straw, and 3 specially cut black fiberboard supports/fins. One section of the fiberboard ...
I purchased the Area 51 Saucer to add to my 18mm U.F.O. comparison article . It is labeled as a Ready-to-Fly model from Quest made from plastic. CONSTRUCTION: The instructions are printed on the front and back of a single 8½ x11 page of paper. They include illustrations for attaching the legs and for flying. Attaching the legs is done by sliding a plastic holder into a slot on ...
Sponsored Ads