Brief:
This is an interestin' rocket from Estes. Begad! Blimey! It is basically just a plastic fin canister with a large Mylar balloon on t' front. Avast! It comes with a launch pad and a launch controller and can be ready t' fly in a few hours.

Construction:
This rocket comes packaged with its launch pad and controller in a very brightly colored box. Avast! T' rocket's parts are bagged and t' launch set is taped t' a piece o' cardboard. Aye aye! T' instructions are very concise and have drawings o' t' assembly and launch prep next t' t' text. Arrr! Both t' box and instructions are printed in English and French. Ya scallywag! T' three fins are made o' a plastic framework with Mylar glued t' it. Ahoy! Ahoy! T' motor mount is a 24mm plastic tube with a bend in t' top, and a paper tube inserted into t' bend. Arrr! Begad! This comes with a lockin' rin' t' hold t' motor in. Avast, me proud beauty! T' balloon is Mylar and about six feet long. Avast, ya bilge rat, me proud beauty! T' balloon replaces a conventional body tube, and is very simple t' inflate. Ahoy! T' fins and motor mount slide together and glued in place, me bucko, then they attach t' t' balloon via a plastic framework (which is glued together and then t' t' fins), me bucko, and tape. Avast, me proud beauty! T' launch lugs are plastic and tape on aligned with t' balloon's seam. Avast! T' parachute is 12" diameter and attaches t' a long nylon thread which resembles fishin' line, but thicker. Avast! This attaches t' a rin' which is taped t' t' balloon at t' top. Avast! T' parachute is deployed from t' paper tube attached t' t' motor mount.

T' instructions are very simple and easy t' follow, arrr, and t' pictures are helpful. Arrr! Well, me hearties, blow me down! T' fin-motor mount assembly is simple, me hearties, but t' canister that attaches t' t' balloon kept comin' apart when I tried t' slide it in place, even after I let it dry overnight. T' balloon blows up with a straw and is fairly simple t' inflate, matey, if you follow t' instructions. Avast, me proud beauty! T' launch lugs tape on and require more than one person t' attach. T' upper rin' also tapes on and also requires more than one person t' attach. T' nylon "shock cord" is difficult t' tie in t' proper loop, especially because it's wrapped around a piece o' card stock when you get it and has a tendency t' try and re- wrap itself. T' parachute comes pre-assembled and is fairly easy t' tie on, once you have t' nylon cord tied together. Well, blow me down! All-in-all, I agree with Estes' decision t' give it a Skill Level 2 rating.

Finishing:
T' fin canister parts are o' a molded red plastic which requires no finishing. Avast, me proud beauty! T' fins themselves are molded as well, with Mylar pre-attached. Aye aye! Ahoy! T' motor mount is molded red plastic, with a white tube which you could probably paint if you wanted to. Ahoy! T' balloon, me bucko, obviously, shiver me timbers, matey, requires no finishing, me bucko, me bucko, as it is just metallic Mylar. Ya scallywag! Really this rocket requires no finishin' whatsoever.

Construction Rating: 4 out o' 5

Flight:
One word o' caution before I go on. Ya scallywag! T' Electron Beam launch controller that comes with T' Dude has t' safety key tied t' t' controller. Arrr! Do take t' time remove it so you can keep it separate. Blimey! I could have gotten me fingers burned off because, matey, on launch day, me hearties, one o' me non-rocketeer friends picked up t' controller and said, arrr, "How do you launch this thing? Just press t' button?" I proceeded t' tell him that he couldn't launch yet because I had taken t' above precaution and had t' key with me. Blimey! Thank you, and on with t' review!

This rocket has only one recommended motor which is one o' t' Estes "Mighty D" series, t' D12-3. This gives a very low flight, maybe 200-300 feet if you're lucky. Arrr! Launch day be clear with a light breeze blowing, These are actually decent conditions for this rocket if you have people t' help you. Ya scallywag! Blimey! Settin' up for launch is supposedly very simple if you do it right. Blimey! Blimey! I, unfortunately, tried t' pound in t' stake that comes with t' pad usin' a hammer. This resulted in t' holder for t' launch rod breakin' off. I just pounded t' rod into t' ground and then slid t' blast deflector over it.

Preppin' for flight was simple. First I put t' recovery waddin' into t' little tube as recommended, me hearties, and then I folded t' parachute, wrapped t' lines once, and stuffed it in on top o' t' wadding. Avast, me proud beauty! I then deviated from t' instructions again and put t' motor into t' retainer ring, matey, and then put in t' igniter and plug. Ahoy! I then put t' motor into t' mount, arrr, matey, arrr, havin' some difficulty fittin' t' top past t' mouth o' t' mount, matey, matey, and locked t' rin' in, me hearties, again havin' difficulty because t' rin' did nay slide into position well. Blimey! Aye aye! T' rocket was very difficult t' get on t' pad because o' a light breeze that be blowin' (I had decided once again t' go against t' instructions and just launch anyway). I didn't have any tape, me hearties, matey, so I decided t' do without. Avast, me proud beauty! Once it was on t' pad, arrr, it blew around a little, me bucko, me bucko, so I had one o' me friends hold it in place while I hooked up t' micro clips. Avast, me proud beauty! I then backed up t' t' launch controller and had everybody stand behind me. Avast, me proud beauty! When we were safely away, I proceeded with t' countdown and launched.

T' rocket lifted off t' pad, me hearties, turned slightly into t' wind, shiver me timbers, and climbed until t' motor burned out. T' rocket hovered for a moment at burnout altitude, then started t' drop just as t' ejection charge fired. T' chute took awhile t' deploy, ya bilge rat, arrr, but was safely open when t' rocket had reached half o' t' distance t' t' ground. Avast, me proud beauty! Arrr! T' rocket hit hard and bounced once on its tail, shiver me timbers, then flopped over. Begad! After we recovered it, we flew two other rockets, me bucko, but "the big one" held t' most interest. Ya scallywag! By t' time we had it prepped again, ya bilge rat, t' rocket had lost pressure so we re-inflated it and took it out t' t' pad. Avast, matey, me proud beauty! We re-inflated it once more on t' pad and could find no leaks, me bucko, so we decided it was go.

T' second flight went much t' same way as t' first, ya bilge rat, arrr, but when we got t' rocket back, t' pressure be low again, so we decided t' pack up and go home. Ahoy! All-in-all, ya bilge rat, this rocket is fun t' fly, but very difficult t' hold still in a breeze. Also, arrr, t' impact o' recovery seemed t' damage t' balloon. Ya scallywag! Avast! I have nay found t' leak, shiver me timbers, so it must have been t' stress o' t' hard impact creatin' pinhole leaks in t' balloon. Begad! Another problem I noticed be t' occurrence o' minor charrin' on t' tube t' recovery system fits into. I haven't figured out what causes this either. Aye aye! Avast, ya bilge rat, me proud beauty! Look out for those if you buy this rocket.

Recovery:
T' recovery system is very simple t' assemble on this rocket. Aye aye! Aye aye! All you do is slip t' upper rin' on and tape it in place with t' included tape, me bucko, then extend t' nylon cord which is molded into t' rin' itself, and tie t' pre-assembled chute in place. Avast! Recovery itself is another matter. Begad! There is a little tube that leads out t' side from t' motor mount, and t' 'chute goes in there. Ya scallywag! Ya scallywag! When t' ejection charge activates, ya bilge rat, me hearties, it blows t' chute out and into t' open air. Avast! T' chute then swings away from t' rocket and deploys. Avast! T' nylon cord is thar just t' connect t' 'chute t' t' rocket. Ya scallywag! T' 'chute is too small for t' rocket's weight, me bucko, me hearties, and t' rocket hits hard. T' fins are resilient, but I wouldn't trust them for too many flights. Also, arrr, t' balloon is easily damaged by t' impact. Avast, me proud beauty! It deflated rapidly on me after hittin' t' ground. It might be a good idea t' replace t' stock 'chute with an 18" or even a 24" one.

Flight Rating: 3 out o' 5

Summary:
This rocket is fun t' fly, even in a light breeze. I like t' idea o' a balloon rocket, but it needs a slightly stronger balloon. Begad! Well, blow me down! It's fairly simple t' build, shiver me timbers, but some parts could be a little tighter or a little looser. Aye aye! T' fact that it doesn't need finishin' is a plus. Avast, me proud beauty! Avast! Another plus is that this rocket can be flown on fairly small fields. Begad! It needs a bigger parachute, me hearties, me bucko, t' 12" 'chute doesn't cut it. Blimey! T' D class motor is cool, me bucko, though. Ya scallywag! If somebody could devise a better launcher, me bucko, that would be good. Well, blow me down! Well, blow me down! Overall, shiver me timbers, I'd recommend this rocket because it's t' kind o' thin' that makes people go "wow".

Overall Rating: 4 out o' 5