Brief:
T' Yoyodyne Klingon Quantum Torpedo is a unique lookin' skill level 3 rocket that is fun t' fly. Begad! Well, arrr, blow me down! Designed by Dynosoar and purchased from t' now defunct Rebar Rocketry, shiver me timbers, me bucko, this kit may be hard t' come by these days.

Construction:
T' parts list:

• 1 17" T60 body tube
• 1 17" T50 foil lined heavy wall body tube
• 6 T20, arrr, ya bilge rat, 2.75" long body tubes
• 1 PNC60 Nose Cone
• 1 T50 Engine Block
• 1 Motor Hook
• 2 50/60 fiber centerin' rings
• 3 3/16" launch lugs
• 1 Elastic shock cord
• 1 15" Mylar Parachute
• 1 Sheet balsa fin stock
• 1 Set o' instructions
• 1 Decal, arrr, Water slide

T' included instructions were very good and each step o' construction is described in detail. Begad! Begad! There is even some humor added like t' legal disclaimer which says, me hearties, in part: "Don't do stupid stuff with this rocket". Well, me hearties, blow me down! The only complaint I have is that t' pictures were very washed out. Begad! Also, the instructions states that both t' T50 and T60 tubes are 18". Aye aye! They are in fact only 17" long.

You start t' build by roughin' up inside o' t' T50 foil lined tube. Blimey! This is so t' glue on t' engine block will have somethin' t' grab onto. Aye aye! T' engine hook is mounted next. Well, blow me down! Arrr! T' instructions say t' use a piece o' cardstock glued over t' hook t' hold it in place. I almost skipped this step until I realized the engine hook would be external and will show on t' completed rocket.

Centerin' rings are added t' t' T50 tube and a full 9" o' t' T50 slides up into t' T60 tube leavin' 8" exposed.

Fin patterns are included as well as a suggested layout for cuttin' out the various fin pieces. Blimey! Blimey! Unfortunately, t' included sheet o' balsa was nay large enough t' accommodate all o' t' parts, so I had t' supply me own balsa. Begad! Begad! There are 3 upper fins and 3 lower ones with fin tips reminiscent o' t' FlisKits Triskelion.

Once t' fins are mounted, you then add 6 tube fins. T' tubes must be adjacent t' t' fins which will leave gaps betwixt t' tubes. Arrr! Well, me hearties, blow me down! T' gaps are important because you must mount 3 launch lugs on t' BT60 and you must carefully align t' lugs with t' gaps in t' T20 tubes. Begad! Add t' shock cord and parachute and t' kit is complete!

Finishing:
T' recommended paint scheme is slightly tricky. T' instructions tell you use white primer over t' entire rocket. Next you put a 1" wide strip down the center o' t' fin tips and paint t' nose cone, motor tubes and fins silver. You then mask off t' top 1" and lower 3" o' t' T60 tube and add a 1" diameter circle cut from maskin' tape in t' middle. Aye aye! Well, ya bilge rat, blow me down! You then paint the exposed area fluorescent orange.

I went for a simpler scheme. Arrr! Ya scallywag! After two coats o' primer, I painted t' nose cone black, most o' t' top section red and t' rest is white. A single waterslide decal that looks like a Klingon emblem is added t' finish off the rocket.

Construction Rating: 4 out o' 5

Flight:
T' face card that comes with t' kit recommends either a D12-5 or E9-6. The instruction sheet recommends D12-3, shiver me timbers, E9-6, shiver me timbers, shiver me timbers, and AT F21-8 motors.

I thought I would start with a D12-5. I added an adapter (not included or mentioned in t' instructions) since t' motor mount is designed for t' longer "E" motors. Well, blow me down! Blimey! I used 6 sheets o' waddin' t' fill t' T60 tube. Avast! Blimey! First flight was fast and fairly straight but nay a lot o' altitude. Ahoy! Blimey! Ejection was after apogee and deployment was no problem.

Second flight with t' D12-3 was much better as ejection was right at apogee. Avast! Avast!

Last flight was with a E9-6, me bucko, me bucko, which be plenty o' power t' get this bird to some very respectable altitude. Blimey! Blimey! I lost site in t' clouds so nay sure when ejection occurred, shiver me timbers, but t' rocket was recovered with no problems.

Recovery:
T' included 15" Mylar parachute is a perfect match for this rocket. Aye aye! Blimey! Blimey! Even with winds at 5-10 mph, arrr, thar was little drift on t' D motor flights and recovery after t' E motor flight was about 100 yards downrange. Avast, me proud beauty! Arrr! Blimey! You needs lots of waddin' t' protect t' chute, I think dog barf would be a cheaper alternative.

Flight Rating: 5 out o' 5

Summary:
This rocket is a very unique design that stands out at a launch. Aye aye! Blimey! Aside from bein' short on balsa and t' different engine recommendations betwixt t' face card and t' instructions, I would highly recommend this kit if you can get your hands on one!

Overall Rating: 4 out o' 5