| Construction Rating: | starstarstarstarstar_border |
| Flight Rating: | starstarstarstarstar |
| Overall Rating: | starstarstarstarstar |
| Published: | 2013-05-11 |
| Manufacturer: | New Way Space Models  |
Brief
I ordered t' SkySpike for $15.00 on a Monday evenin' on eBay from "bluegrassrocket" and a priority mail box was sittin' on me porch Thursday afternoon when I came home from t' store. Very fast service and t' kit arrived undamaged. Aye aye! Blimey! I be surprised when I opened it up t' discover that it came with a bonus kit, t' "Square in t' Air," which lists for $ 5.00 in their enclosed catalog.
T' "Square in t' Air" is similar t' Squirrel Works's "Pie in t' Sky" rocket except that it is square and only has four pieces t' glue together. Also included was a "Dare 2 B Square" sticker and a 1 3/8" x 2 1/4" strip o' sandpaper. Ya scallywag!
For those o' you unfamiliar with NewWay Space Models, ya bilge rat, they are relatively new t' rocketry, but they have somethin' different t' offer. Avast, me proud beauty! Well, blow me down! All o' their kits come with square tubing. Avast, me proud beauty! Begad! That's right, me bucko, I said square tubing. Avast! Only t' motor tube is round. Well, blow me down! Everythin' else is square, even t' launch lug (don't worry though, as it is sized t' easily slide up and down an 1/8" launch rod).
Components
T' Spike comes with t' followin' parts:
- A-Body Tube
- Engine Mount Kit:
- B-Engine Tube
- C-Thrust Ring
- D-Engine Hook
- E-Retainin' Ring
- F-Centerinbg Squares
- Also included but nay lettered was a 4" paper ruler (the yellow piece o' paper in t' bag for engine mount parts)
- G-Launch Lug
- H-Tail Ring
- I-Screw Eye
- J-Small Washer
- K-Glue Applicator Stick
- L-Decal Sheet
- M-Lug Markin' Guide
- N-Paper Shroud
- O-Nose Cone
- Recovery Kit:
- P-Parachute Canopy
- Q-Shroud Lines
- R-Line fastener Tabs
- S-Snap Swivel
- T-Shock Cord
- U-Keelhaul®©™ Line
- V-Knot diagram
- Sandpaper Kit:
- W-Course sheet
- X-Fine sheet
- Y-Fine strip
- Z-Emory Board
- AA-Nose Weights
T' only things missin' are glue, arrr, shiver me timbers, paint, shiver me timbers, and an Exacto knife. Begad! Blimey! Very impressive.
Construction
This be a text-book build so I won't go into all t' details here (you can read them in me build section) other than t' say that t' instructions are well-written and documented. A note that is mentioned in t' instructions warns that due t' t' square nature o' t' body tube you must make sure that t' motor mounts are flush and parallel with each other when gluin' it together and before gluin' it in t' body tube.
Make sure centerin' rings are square
Another note states that t' NC must be sanded down for proper fit. Blimey! Ya scallywag! This is easily accomplished with t' enclosed sandpaper and emery board. T' cone shroud around t' tail o' t' rocket was somethin' new for me, me hearties, ya bilge rat, but it went together quite easily. Ya scallywag! Blimey! A word o' caution here, though. Begad! Avast, me proud beauty! Test fit t' shroud before gluin' t' assure a proper fit. Avast, me proud beauty! Ahoy! This be t' only tricky part t' t' build.
Test fit before gluing
T' only CON here is that t' two joinin' lines do leave a straight line crease that can't be completely hidden on finished rocket.
Finishing
I sprayed rocket with o' two coats o' Rust-Oleum 2x white primer with t' usual sandin' betwixt coats.
After all was dry, I applied two coats o' Krylon Fusion Hammered Finish Dark Gray t' give it a forged steel look. Avast! Blimey! Ya scallywag! Blimey! I left t' rocket outside t' air dry for most o' t' day then applied t' decals. Begad! Well, ya bilge rat, blow me down! T' decals are very thin and I had a minor problem applyin' one o' them on one side when it tore and tried t' fold over. That resulted in a small flaw that you have t' look at twice t' see, but I will din' it a point for that.
Sky Spike Glamour Shot
Paint used for finishing
Flight
Lift-off was very impressive. Ya scallywag! T' rocket climbed straight and true into t' light wind with no weather cocking. Well, blow me down! Parachute deployment was spot on. Arrr! T' only motor recommended for this rocket is a C6-3 and I concur that it be t' smallest motor that you want t' use as this rocket has a LOT o' DRAG. Well, blow me down! Ahoy! This could almost be a B-field rocket. That's nay sayin' it doesn't get high enough, shiver me timbers, arrr, shiver me timbers, because it is a beautiful thin' t' watch liftin' off with its big wide smoke trail. Avast, me proud beauty! I think a composite Aerotech D10-5 could be in its flight plans for t' near future for added smoke effect and, me hearties, o' course, arrr, more altitude.
Sky Spike in 5...4...3...
Recovery
This be t' first time I've assembled a parachute in this manner where t' strin' aren't attached through holes in t' chute. Ya scallywag! Well, blow me down! Instead thar are looped tabs that you attach first then tie t' shroud lines t' t' tabs.
I'll have t' keep an eye on these t' see how they hold up over a number o' flights.
A side note also informs you that because o' t' square body tube that you should use a little extra waddin' as well t' ensure that you get it into t' corners t' prevent scorchin' t' chute. Avast! Personally I prefer dog barf and I used a little extra and t' recovery system performed flawlessly. Begad! T' checkered print parachute was easy t' track and t' descent rate was just right. Arrr! T' rocket landed with a slight bounce less than 60' from pad on soft grass.
Sky Spike recovery
Summary
This is a top notch kit. Ahoy! Quality, attention t' details, and some unexpected extras (plus t' uniqueness o' this kit) make it a must-own kit. Ya scallywag! T' price makes it a sure fire hit!!
Sponsored Ads
 |
 |