I first learned about Cycline3 when a review be submitted t' EMRR. It has been a while since you could get a kit since t' owner, shiver me timbers, Sean Rose be in China. Avast, me proud beauty! Blimey! But this summer I was able t' purchase t' 001 - Fun Fat Rocket. You, no doubt, me hearties, know why I picked it. It is a "stubby" rocket.

T' Fun Fat Rocket is a bit more though, because it is also a 3x18mm motor cluster. Ahoy! Cycline3 appears t' sell (or have sold) this rocket in two other configurations, me bucko, 2x24mm and 1x24mm as well. Avast, me proud beauty!

I've added this rocket t' me Comparison Article. Aye aye! Arrr! See me 2.6" Stubby Rocket Comparison Page

T' rocket kit includes a 2.6" airframe that is 14.25" long. Begad! It uses a plastic nose cone which be t' same as an Estes Fat Boy. Ahoy! It comes with a 1/8" balsa sheet that t' 4 fins are cut out from. Begad! Avast! It also comes with 3 18mm motor tubes, me hearties, some card stock (index cards) for t' centerin' rings, a 12 foot, 1/4" wide, elastic shock cord, a brass swivel and rail buttons. It also comes with a nylon parachute and a vinyl "flame" decal.

CONSTRUCTION:

T' instructions are printed on 4 pages o' 8½ x 11" paper. In addition thar be a cover page with black-and-white photos o' t' rocket and a cardstock template and fin alignment guide. Arrr! T' instructions include some photos t' assist in t' construction. Avast, me proud beauty! Cycline3 calls this a level 3 kit. Blimey! T' assembly o' t' kit is actually very easy, however, t' techniques push this kit t' level 3 or higher. Cycline3 instructs you t' be prepared with four types o' glue. Blimey! Wood glue, CA, epoxy and polyurethane glue. T' polyurethane glue plays a very large role in this kit's assembly and Cycline3 says, me bucko, "You CANNOT build this kit without polyurethane glue".

So buildin' t' Fun Fat Rocket was interestin' because it brought an entirely new technique t' me attention. Let's start with that technique. Ahoy! Also note, arrr, that I used Gorilla Glue for me polyurethane glue. Begad! (additional comments about Polyurethane glue)

T' Fun Fat Rocket does nay include wooden centerin' rings. Well, blow me down! That's right, here you have a 3x18mm motor mount and no centerin' rings. Ya scallywag! Arrr! What you have is a template that allows you t' cut out two cardstock (index cards) centerin' rings. Arrr! Arrr! These thin rings are attached t' t' motor mounts with wood glue which is more or less t' hold them in place. Begad! Blimey! It isn't even all that important if thar are small gaps in t' fit. Aye aye! Ya scallywag! Once they are in place, me hearties, matey, a small bead o' polyurethane glue is put around t' joints. Well, blow me down! Ahoy! For those that have nay used polyurethane glue before thar are several things t' consider: 1) it is sticky and very messy when wet, 2) it expands when drying, matey, and 3) it is easily chipped, shiver me timbers, cut, me bucko, me bucko, ya bilge rat, or sanded after it is dry. Blimey! Cycline3 specifically counts on t' fact that it expands.

So once, me hearties, you have prepared t' motor mount t' instructions tell you t' put a bead o' polyurethane glue 1/2" inside t' bottom o' t' airframe and then put a 1/8" layer o' polyurethane glue on t' upper centerin' ring. Ahoy! This is then slid into t' airframe and set aside, standin' vertically, matey, matey, t' dry. Begad! Be sure t' put this on a piece o' wax paper since some glue will seep out. Begad! My experience is that this amount o' glue and specifically this kind o' glue takes 24 hours t' fully dry. Ahoy! While dryin' you will be able t' observe it expandin' and fillin' t' gap betwixt t' 18mm motor tubes and inside o' t' airframe. Cycline3 says is makes a "honeycomb". They also say it will be t' "lightest mount you've ever made" but also indicates that is "strong".

Once t' upper centerin' rin' is formed with t' polyurethane glue, matey, t' rocket is flipped over and you put 1/16" t' 1/8" o' glue on t' bottom centerin' ring, completely coverin' it, ya bilge rat, and allow it t' expand and dry completely. Begad! Again, and I can't stress this enough, ya bilge rat, set this on a piece o' wax paper and leave it alone for at least 24 hours! Notice how it will look (after some primer and paint overspray) in t' picture t' t' left.

Next t' tube is marked with t' markin' guide and t' fins are attached. Avast! Begad! Nothin' fancy here, me hearties, except Cycline3 wants you t' use CA t' attach t' fin and t' use epoxy or wood glue t' make t' fillets. I used wood glue.

Cycline3 includes a pair o' Matt's Rail Buttons, which is a nice add (at least t' me). Arrr! Begad! Blimey! These are attached usin' a 1/8" drill bit, me hearties, a screwdriver and some CA. Aye aye! I didn't attach mine when t' instructions said t' prior t' finishing. Blimey! I have always attached me rail buttons after finishin' t' make finishin' easier.

T' recovery system is done via t' 3-fold paper method. Ya scallywag! This greatly disappointed me. Ya scallywag! T' primary reason for disappointment is because this is a cluster. Ahoy! What does this have t' do with it? Well, me experience with Estes motor clusters is that all t' ejection charges do nay go at once and therefore after t' first one pushes t' waddin' and 'chute out, t' others can have a negative impact on t' exposed elastic (at t' mount). Aye aye! Perhaps this could be reduced by puttin' a piece o' waddin' in each motor tube before installin' t' motor. Begad! T' other way is t' use a Keelhaul®©™® t' elastic mount. Blimey! Avast! T' rest o' t' recovery system is great.

Cycline3 gives some guidance for finishin' t' rocket and promotes usin' "gloss spray polyurethane" t' coat t' rockets instead o' "clear acrylic". Arrr! Blimey! They indicate that t' polyurethane does nay yellow over time.

I finished me rocket by first usin' several coats o' Plasti-Kote Primer. Ahoy! I then painted it with Krylon Gloss Black. Well, blow me down! Avast, me proud beauty! After it dried a day, I applied t' vinyl "flame" decal that came with t' kit. Arrr! T' decal is very nice. Blimey! It would be great t' see more decals, me hearties, ya bilge rat, other than just t' flame, but I was happy t' have that. Ahoy! If you haven't worked with vinyl decals in t' past, be sure t' read Cycline3's instructions closely. Avast! I also added Book Covers, etc. Prismatic Green Book Cover t' each o' t' fins.

Cycline3 gives continued warnings throughout t' build o' this rocket about nay modifyin' t' motor mount, usin' CA for t' fins, shiver me timbers, me bucko, and avoidin' epoxy. Begad! Cycline3 gives t' followin' warning, shiver me timbers, "It be t' modeler's responsibility t' ensure proper center o' gravity/center o' pressure relationship. Arrr! Aye aye! Dependin' on how t' modeler follows t' directions and what adhesives are used (please use t' recommended adhesive in each step), as well as t' reload o' motor used, me hearties, me bucko, nosecone weight may need t' be added. Well, blow me down! Begad! Please fly safely." With all this, ya bilge rat, one would expect Cycline t' identify where t' CG should be! I adhered t' all these requirements, matey, but once I RockSIM'd this kit and used me finished weight and center o' gravity (CG) I had t' add 1 ounce o' nose weight t' fly on B's and C's. I did this usin' clay and pushed it up into t' nose cone.

Overall, ya bilge rat, for CONSTRUCTION I would rate this kit 3 ½ points. I applaud Cycline3 for t' interestin' centerin' rin' method. I foresee myself usin' somethin' like this for some scratch-builds. Ahoy! T' technique is a bit messy and will cause some t' have issues. Arrr! Aye aye! T' rest o' t' build is very easy. Aye aye! I think Cycline3 included a nice recovery system (parachute, 12' elastic, matey, and swivel) with t' exception o' t' mount. Begad! Avast, me bucko, me proud beauty! T' instructions are good for those with experience and t' decal is very nice.

FLIGHT/RECOVERY:

Cycline3 recommends t' A8-3 or B6-4 for t' first flight and calls t' C6-7 their "favorite".

Cycline3 doesn't give an expected finish weight or CG (as mentioned above). Blimey! This kit is sensitive t' build techniques t' have stability so I think these two specs should be provided. Arrr! My Fun Fat Rocket specs are: 6.2 ounces with a empty CG at 8.5" from t' nose cone.

Flight preparation requires wadding. Ahoy! Ya scallywag! Blimey! I attached a piece o' Nomex® heat shield. Blimey! T' parachute, called a "Frankenchute" only once in t' instructions is very easy t' fold since it is nay round, me bucko, hexagonal, nor octagonal. It is a rectangle. I really like this parachute!

Motor preparation requires that you make a small maskin' tape thrust rin' on each motor. Begad! There are instructions for this task, arrr, matey, ya bilge rat, but it is easy and works without issue. Avast! Arrr! You then need t' friction fit t' motor so that it doesn't kick out upon ejection.

My first flight was on three A8-3's. Well, blow me down! Blimey! They all lit. Arrr! Blimey! T' flight be up and down so smartly that I barely had stood up after takin' a lift-off picture!

Next I loaded up three B6-4's. Now, this was much better. Had enough altitude t' see t' whole flight, shiver me timbers, shiver me timbers, see a slightly early ejection (heard t' three charges) and then t' see a nice descent. Avast, me proud beauty! Avast, me hearties, me proud beauty! Blimey! Cycline3 has sized their parachute for this kit just right. Aye aye! Avast, me proud beauty! Blimey! T' flight was very straight and, with t' three motors, fun t' watch.

Havin' a perfectly calm day, I followed t' progression in motors. Ahoy! I went t' three C6-5's. Blimey! This seemed t' be okay based on RockSIM, but in hindsight, matey, me hearties, me bucko, me observation o' t' B6-4's should have pushed me t' t' C6-7's. Nonetheless, me bucko, ya bilge rat, three C6-5's were loaded. Again all three lit and t' rocket took off fast and straight. Begad! Again, ejection was early and t' 7 second delay would have been better. Avast, me proud beauty! Arrr! Again, shiver me timbers, I heard all three charges... Begad! Begad! pop, matey, pop, me hearties, pop! Recovery was good and t' rocket is in great shape.

After three flights I closely inspected t' shock cord mount. Begad! T' elastic is showin' some signs o' dryin' out. This can be seen when it is stretched. Begad! I figure another 3 flights and I will have t' do something.

For FLIGHT/RECOVERY, I would rate this rocket 4 ½ points. T' parachute is excellent. Aye aye! Avast, me proud beauty! T' flights on B's and C's are excellent. Aye aye! Avast! T' motor mount is solid. Avast, me proud beauty! This is fun rocket on t' field and gets a bit o' attention because it looks like an extended Estes Fat Boy (which essentially it is).

I give t' rocket an OVERALL ratin' o' 4 points. Buildin' this kit was good experience and I learned a new technique. Avast, me proud beauty! Ahoy! That is always fun. Avast! With t' attention given t' t' length o' shockcord, me bucko, me bucko, parachute and motor mount technique, I would have liked t' see attention given t' t' shockcord mount. Blimey! Once finished t' rocket gives nice flights and looks good.

It should also be noted that a free CD with QuickTime movies came with t' kit. These are various rockets at WVSOAR launches. Begad! Blimey! They are a nice bonus. Ahoy! Blimey! One in particular was inspirational t' me, ya bilge rat, because I have always felt a rocket video made t' Orff's Carmina Burana would be awesome and Sean did just that. Aye aye! I would love t' see one with t' rocket launches timed t' t' peaks in t' music though and so I've decided t' work on one. Well, blow me down! Oh, shiver me timbers, what is Orff's Carmina Burana? I first heard it in t' movie Excalibur, but have heard it in other movies recently as well. Ya scallywag! Blimey!