Brief:

T' Maxi Streak #1837 is a long time OOP rocket from Estes. Well, blow me down! Ahoy! Got t' plans off JimZ's website. It is like an upscaled mosquito with swept back fins or a streak with rounded fins and upscaled. Well, blow me down! T' instructions call for a 24mm motor mount, ya bilge rat, which I changed for an 18mm mount: a D or E motor would put this thin' into space.

Modifications:
T' maxi streak is a very quick build. Aye aye! Blimey! T' instructions are o' t' normal Estes quality. Blimey! I don't like t' tri fold method for anchorin' t' shock cord, matey, instead I use a steel fishin' leader attached t' t' motor mount, ya bilge rat, arrr, this also stop burnin' issues t' t' shock cord.

T' mount be glued into t' body tube, t' instructions called for t' end o' t' mount t' extend beyond t' end o' t' tube, I put it in flush t' give t' rocket a cleaner line.

Construction:
T' build t' Maxi Streak is used: 1 engine holder BT-20J

• 1 engine block EB-20A
• 2 centerin' rings RA-2060
• 24 inches elastic shock cord
• 1 6.75 body tube BT-60
• 3/16 balsa sheet
• 1 plastic nose cone PNC-60MS
• 24 inch mylar streamer
• 1 steel fishin' leader
• 1 launch lug
• 1 swatch o' Nomex cloth
• 1 Decal from excelsiorrocketry

Finishing:
T' fins o' t' model were given a few coats o' sandin' sealer and t' rocket be primed and sanded.

T' rocket was given several light coats o' metallic red paint, arrr, after this dried one fin was masked off and given a few coats o' gloss black paint, me hearties, ya bilge rat, as be t' nosecone.

I went with red paint, ya bilge rat, because t' picture o' t' Maxi Streak on t' Jimz site has t' rocket in red. Avast, me proud beauty! however, t' instructions have t' rocket bein' painted orange, shiver me timbers, which I read after i had painted mine - so that's another deviation from t' original.

Initially I was nay goin' t' put a decal on t' rocket, shiver me timbers, me bucko, but after postin' this build on TRF, Gordy from excelsiorrocketry said he had one and as i have been very happy with t' quality o' his decals in t' past i bought one t' finish t' model properly. Well, blow me down! Ya scallywag! Gordy has since told me that he has sold a few more Maxi Streak decals t' other poeple.

Flight:
T' original recommended motors were D11-9, shiver me timbers, ya bilge rat, arrr, D12-5, ya bilge rat, D12-7. With t' 18mm mount i would go with A8-3, B6-4, arrr, C6-5.

Flights were made with all three motors in t' same day. Each flight was arrow straight, me bucko, arrr, with a steady increase in altitude.

I got t' drag race me Maxi Streak against another Maxi Streak at me club's monthly meetin' on t' 21st o' March. Ahoy! Arrr! I lost.

Recovery:
T' original Maxi Streak recovered via a streamer, given t' low mass and potentially high altitude then that's a good choice.

I went with about 4 foot o' two-inch wide Mylar streamer.

Recovery is quite fast, me hearties, but safe. Blimey! Begad! Each flight had t' streak land fairly near t' pad and more importantly without damage.

Summary:
Pros: A good performance rocket that looks good, me hearties, especially with t' excelsoirrocketry decal. Avast, me proud beauty! Blimey! Arrr! Blimey! Flights are stable and fast.

Cons: Streamer recovery may result in some damage t' t' swept back fins, ya bilge rat, me hearties, but none has been seen yet.