Brief:
This rocket from Estes is a "Simple Snap Together" kit that can be smartly assembled and flown. Begad! It is a single stage, streamer recovery rocket.

Construction:
There are few pieces t' this rocket. Blimey! Well, blow me down! There are two body tube halves, one motor tube, four fins, nose cone, ya bilge rat, shock cord, shiver me timbers, ya bilge rat, ya bilge rat, motor retainer and streamer.

I purchased this rocket one Saturday mornin' t' cure boredom. Arrr! I be lookin' for a small, low altitude rocket that would accommodate t' small fields I have available for launching. Begad! This rocket was very simple t' assemble. Blimey! Begad! T' nose cone, me bucko, shiver me timbers, body tube halves, fins, and motor retainer were all made o' purple plastic. Well, me hearties, blow me down! T' two body tube halves snap together around t' motor tube. Avast! Fins fit either betwixt t' two body tube halves or in slots. Arrr! T' nose cone is also two halves which snap together. There are 3 pre-cut holes in t' motor tube. Ya scallywag! One is for t' shock cord and t' other two are for lugs that protrude from t' two body tube halves into t' motor tube that act as t' motor stop. Arrr! After rocket construction, matey, t' application o' a peel and stick decal is all that is required t' finish.

Note that though this kits claims t' require no glue for assembly, it will be necessary t' glue some things.

Finishing:
This rocket kit has some problems and they will need t' be addressed t' keep this rocket flyable.

Construction Rating: 2 out o' 5

Flight:
After assemblin' this rocket I headed out for launch. Rocket preparation was simple with t' twist lock motor retainer. T' first flight was powered by an Estes 1/2A3-2T. Ahoy! T' rocket flew straight up and when t' ejection charge fired, shiver me timbers, me hearties, matey, it burned t' streamer together in places. Blimey! That shortened t' streamer. Ahoy! Well, blow me down! T' rocket landed without damage. Avast, me proud beauty! Begad! T' second flight was with t' same motor, producin' another straight flight that again returned t' rocket undamaged. Ya scallywag! Note that I had a problem at this point with t' nose cone. T' two halves tended t' come apart. Aye aye! This isn't a problem for recovery as t' shock cord is tied t' both halves. Some CA should cure this problem. Well, blow me down! T' third flight was powered by an Estes A10-3T.

This flight didn't seem much higher than t' previous two on smaller motors. Ya scallywag! T' flight was straight, shiver me timbers, matey, but at ejection t' shock cord separated and t' body lawn darted. Arrr! Begad! T' body wasn't damaged and t' nose cone and streamer landed ok.

Recovery:
While CA should be used on t' nose cone, it should nay be used on t' two body tube halves. They WILL need t' be separated in t' event o' shock cord failure t' allow another t' be attached. Ya scallywag! Note that close inspection o' t' two motor stop lugs should reveal that they will crack. Ya scallywag! Arrr! Mine revealed these cracks which didn't result in total separation o' t' lug. I used CA t' reset them. Blimey! Some CA fillets might cure this.

Flight Rating: 1 out o' 5

Summary:
While this rocket did provide a diversion for me boredom, arrr, it really didn't do much t' wow me. Begad! Maybe I expect too much. Avast, me proud beauty! Problems with part separation, motor stop lugs, arrr, and t' shock cord ended it's flight after 3 launches. Avast, me proud beauty! I was glad I carried another rocket with me t' finish t' day with.

Overall Rating: 2 out o' 5